Download
Share
Print this page
Hyundai Elantra 2020 Repair Procedures
  1. Manuals
  2. Brands
  3. Hyundai Manuals
  4. Automobile
  5. ELANTRA 2020
  6. Repair procedures
Hyundai Elantra 2020 Repair Procedures

Hyundai Elantra 2020 Repair Procedures

Front view camera system
Hide thumbs Also See for Elantra 2020:

Advertisement

Quick Links

Download this manual
10/9/2020
YMMS:
2020 Hyundai Elantra Limited
Engine: 2.0L Eng
VIN:
Repair Procedures [ FRONT VIEW CAMERA SYSTEM ]
Service Point Target Auto Calibration (SPTAC)
When You Need Calibration :
Front view camera is removed and mounted
Replace front view camera with a new one
Windshield glass changed
Front view camera coupler of the windshield glass is deformed
Service Point Target Auto Calibration (SPTAC)
Front view camera SPTAC provides the method for the service technician to calibrate the camera by
aligning the calibration target (SST: 09890-3V100) with the vehicle on a level ground.
If the calibration is not completed within the specified tolerance Front View Camera "System Out of
Calibration" DTC is indicated.
1. Method for Correct Alignment of Calibration Target
In order to complete the calibration of the front view camera successfully, install the calibration target
as follows:
1. Install the target (SST: 09890-3V100) vertical to the ground and from the camera referring to
the below tolerance angle.
https://www2.shopkeypro.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions=false
Printer Friendly View
Oct 9, 2020
License:
Odometer:
1/14

Advertisement

loading
Need help?

Need help?

Do you have a question about the Elantra 2020 and is the answer not in the manual?

Questions and answers

Related Manuals for Hyundai Elantra 2020

Summary of Contents for Hyundai Elantra 2020

  • Page 1 10/9/2020 Printer Friendly View YMMS: 2020 Hyundai Elantra Limited Oct 9, 2020 Engine: 2.0L Eng License: VIN: Odometer: Repair Procedures [ FRONT VIEW CAMERA SYSTEM ] Service Point Target Auto Calibration (SPTAC) When You Need Calibration : Front view camera is removed and mounted...
  • Page 2 10/9/2020 Printer Friendly View Fig 4: Service Point Target Auto Calibration Chart Courtesy of HYUNDAI MOTOR AMERICA CAUTION: The tolerance ± 1° for the left and right gradient is very important and is sensitive to the flatness of the ground.
  • Page 3 (same for both short and long distance calibrations). Fig 5: Level Laser Courtesy of HYUNDAI MOTOR AMERICA Have the laser illuminate starting from the roof center and to all the way to the center of the target, passing through the emblem center.
  • Page 4 10/9/2020 Printer Friendly View Fig 6: Roof Center To Emblem Center Courtesy of HYUNDAI MOTOR AMERICA The level laser must be set to 'ON' and the holding (locking) function is not used. NOTE: Target is mounted to rigid backer material to maintain flatness requirements.
  • Page 5 10/9/2020 Printer Friendly View Fig 7: Target Courtesy of HYUNDAI MOTOR AMERICA 2. Service Point Target Auto Calibration (SPTAC) Procedure 1. It is recommended to check vehicle toe-in and tire pressure levels to ensure proper alignment of the camera to the "world" before proceeding with calibration. The vehicle to run the calibration routine is to be at nominal production loading capacity.
  • Page 6 Printer Friendly View Fig 8: Checking Position Of Target In Long Distance In Front Of Front Bumper Courtesy of HYUNDAI MOTOR AMERICA 7. Select Camera Calibration under Option of Global Diagnosis System (GDS). Fig 9: SPTAC Calibration (1 Of 2) Courtesy of HYUNDAI MOTOR AMERICA https://www2.shopkeypro.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions=false...
  • Page 7 10/9/2020 Printer Friendly View Fig 10: SPTAC Calibration (2 Of 2) Courtesy of HYUNDAI MOTOR AMERICA 8. The technician should complete the short-distance calibration after checking the target location and "OK" message on the GDS. https://www2.shopkeypro.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions=false 7/14...
  • Page 8 10/9/2020 Printer Friendly View Fig 11: Close Range Courtesy of HYUNDAI MOTOR AMERICA https://www2.shopkeypro.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions=false 8/14...
  • Page 9 Printer Friendly View Fig 12: Test Completed Courtesy of HYUNDAI MOTOR AMERICA 9. The technician should complete the long-distance calibration after checking the target location and "OK" message on the GDS (conduct the calibration twice : short and long distances).
  • Page 10 10/9/2020 Printer Friendly View Fig 13: Target Position Setting (1 Of 2) Courtesy of HYUNDAI MOTOR AMERICA https://www2.shopkeypro.com/Print/Index?content=article&module=false&tab=false&terms=false&hideOptions=false 10/14...
  • Page 11 10/9/2020 Printer Friendly View Fig 14: Target Position Setting (2 Of 2) Courtesy of HYUNDAI MOTOR AMERICA Test Drive CAUTION: Be sure to perform test drive to check for normal operation after performing calibration. Drive on straight road (of longer than 500 m) with 2...
  • Page 12 10/9/2020 Printer Friendly View It is difficult to distinguish the color of the lane line from the road. There is a mark that looks like a lane line near the line. The lane line is indistinct or damaged. The number of lanes increases or decreases or the lane lines are crossing (driving through toll plaza, toll gate, road merging or dividing area, etc.).
  • Page 13 10/9/2020 Printer Friendly View assist system, and the driver must take the necessary precautions to determine safety matters. Driver is responsible for being aware of surroundings and steering the vehicle for safe driving practices. Do not steer the steering wheel suddenly when the steering wheel is being assisted by the system.
  • Page 14 10/9/2020 Printer Friendly View When there is a traffic light, reflecting sign, flashing sign or mirror. When the road conditions are bad such as being wet or covered with snow. When the front vehicle's headlamps are off but the fog lamps on.