Robic SC-800EL Operating Manual

USING THE ALARM AND/OR HOURLY CHIME
The alarm can be armed (set to go off) to sound once per day. The alarm symbol (((•)))
will appear when the alarm is armed.
The hourly chime In your watch can be armed (set to go off) to sound one (1) beep
every hour on the hour. The chime Indicator £, will appear when the hourly chime is
armed.
ARMED AND DISARMING THE ALARM AND HOURLY CHIME
The alarm wl 11 automatically be armed (set to go off) after you set the a'arm tlme^The
symbol (((•))) will be visible above the "P" indicator on the lower row of the display, or,
With your watch In normal time (no digits appear flashing);
(1) Press (C) and the chime symbol & appears armed to sound t'0^-
(2) Press (C) again, and the chime symbol disappears, and the alarm symbol ((( )))
?3^s*W
a'arm symbols disappear. Both are
disarmed.
III.
SPEED CHRONOMETER • HOW TO OPERATE
To enter the speed mode from normal time, press (B) once. If the speed timer Is
running, stop timing by pressing (E) once. Reset the display to all zeros by pressing
(F) once or twice.
The display appears as follows:
gazoo anon
goa
05
s c-
00^00 00 ao
- SET DISTANCE
IN MILES
- TRACK DISTANCE IS
SET At 1/4 MILE (0.250)
_ FLAGS SHOW SPEED
MODE IS STOPPED _ .
Thank you for buying the Robic SC-800EL. Your purchase brings you a world class
timer with a wide range of professional features and functions that are applicable to
numerous timing activities for sport, science & technology.
To ensure maximum enjoyment from your timer, please take a few minutes to
carefully review this operating guide.
Once you are familiar with Its operation, you will be ready to enjoy Its manyfine
features, which include the following modes of operation; normal time, speed
chronometer, chronograph and countdown timer.
NORMAL
NORMAL TIME
• Hours, Minutes, Seconds
• Day, Month, Date
• Alarm Time
• Alarm, Chime, AM/PM Indicators
• Normal 12 Hour or Military
• 24 Hour time Option
• Mode Switching
• EL Backlight
SPEED CHRONOMETER
• 25 Hour Timing with 1/100
Second Resolution
• Set Distance 0.1 to 999.999 mi/ki
• Speed from 1.0 to 999.999 mph/kph
• Fifty (50) Lap. On-demand Memory
• Average Speed of Multiple Laps
• Lap Count (0) to (999)
• Time-Out
• Mode Switching
• EL Backlight
CHRONOGRAPH
• Twenty-five (25) Hour with 1/100
Second Resolution
• Simultaneous Display of Lap, Split
and Accumulated Times
• Lap Count to 999
• Fifty (50) Lap, On-Demand Memory
On-Demand, Average LapTrme
• Mode Switching
« EL Backlight
i; How to Determine and Enter the Track Distance
The first step Is to enter the track distance correctly. The speed timer
will not
work
unless a distance Is entered.
Distance Is entered as the decimal equivalent of a ml1® °„r^l"n;f*8r<,,^Tl *°
999.999. For example, enter 2 1/4 miles/kilometers as 002.250,1/3 as 000.333,1/8 as
000.125 etc.
You may convert feet to the decimal equivalent of a mile, l.e. 187 feet Is entered as
000.035 (187 divided by 5280 = 0.035).
Convert meters to kilometers as follows; 230 meters is entered as 000.230 (230
divided by 1000 = 0.230).
2. Enter Track Distance
To enter the track distance when the timer Is stopped and reset to zeros, proceed as
follows:
A. Press and hold (A) until "mile" or "km" appears flashing In the upper right hand
corner of the display. Press (C) until the desired unit of measurement (Mile or KM)
appears.
B Press (B) and the first digit of the distance scale (Row 2) 000.000 appears flashing.
Advance the digit (0-9) by pressing (C) until the desired digit aPPaars'1"*■ "l™6
to the second digit by pressing (B) once. Change the second digit by pressing (C).
Continue to set each digit on the distance scale until you have entered the correct
distance. Press (A) to end the distance setting process. The distance set will appear
and no digits will be flashing.
COUNTDOWN TIMER
• Normal Time Display
• Countdown, Auto-Repeat Timer
• Working Range Ten (10) Hours
• Timer Reset During Countdown Operation
• Mode Switching
• EL Backlight
PRESS (B) _
ROW 1
ROW 2
ROW 3
00Z00 0.0 00
OOZ
55 00
00:00'00'00
- DISTANCE SET AT
2 1/2 MILES (2.500)
-FLAGS SHOW SPEED
TIMER STOPPED
NOTES:
1. Should you need to set any particular digit on the distance scale, press (A) until
"mile" or "km" appears flashing. Then press (B) until the correct digit appears
flashing. Change the dlglt(s) by pressing (C). To end the setting procedure, press (A)^
2. The maximum setting distance Is 999.999 miles or kilometers.
3. The speed timer
will not
work unless a distance has been entered.
C. OPERATING THE SPEED CHRONOMETER.
After entering the track distance, you are now ready to operate the speed
chronometer. For this section, assume a track distance of 2.500 (2 1/2 miles).
A ONE LAP EVENT (START / STOP / ACCUMULATED TIME / RESET).
START: Press (E) to start the timer. Run Indicator appears.
STOP: Press (E) again to stop the timer. The Stop indicator appears and 0:00'44"12
seconds has elapsed. The display appears as:
I. EL BACKLIGHT OPERATION
LAP COUNT
IS (001)
Pressing UD" at any time during any operation will activate the Electro-Luminescent (EL)
Backlight function for viewing at night and in low light or no light situations.
Once pressed, the EL Backlight will illuminate the display for three (3) second with a light
blue, back lighting.
IMPORTANT: j ^ t u „
Please use the EL backlight as required, but note it will reduce the product s battery life.
ROW 1
ROW 2
ROW 3
gozoo o.o oo
gO
|?0 }9 89
:--~
pdhof
nn-nnuu'i;
UU'UU
11 Ic
-MILE INDICATOR
_ LAP TIME OF
44.12 SECONDS
ACCUMULATED TIME: Press (F) and the accumulated time will appear in row (3) of
the display.
RESET (all zeros): To return the timer to the start position (all zeros), press (F) again.
The display appears as follows:
II.
NORMAL TIME - OPERATING INSTRUCTIONS
The starting point for operating your watch is normal time. If normal time is not
displayed, press (B) until it appears.
To set the alarm, normal time and calendar, press (B) mode/select until the display
appears as follows:
MONTH 1-12 , ,-
ROW 1
ROW 2
ROW 3
5
0
Z
00 0.0 00
go z
05 50
nn.nnnn'nn
u u-uu UU UU
SPEED CHROHO STOP _.
- ALARM TIME
- SET DISTANCE
IN MILES
- TRACK DISTANCE IS
SET At 1/4 MILE (0.250)
FLAGS SHOW SPEED
MODE IS STOPPED
DAY-
HOURS
RL
-TH
\ 1; 3 f] R-"A" F0R AM
\ j'jU n
"P" FOR PM
j P
-
P
—DATE 1-31
• « _ — — A i-l— ALARM SYMBOL
1^09 36 jP-™™
_ J
"P" FOR PM
- CHIME SYMBOL
MINUTES' SECONDS
To begin the setting process, press and hold (A) until alarm hours begin to flash In
the upper row of the display.
ALARM HOURS; Press (C) to advance alarm hours. The "A/AM" or "P/PM" indicator
adjusts automatically.
ALARM MINUTES: Press (B) and alarm tens of minutes appear flashing.
Press (C) to advance.
NORMAL TIIME SECONDS: Press (B) and normal time seconds appear flashing. Press
(C) to reset to all zeros.
NORMAL TIME HOURS: Press (B) and normal time hours appear flashing. Press (C)
to advance.
NORMAL TIME TENS OF MINUTES: Press (B) and normal time tens of minutes
appear flashing. Press (C) to advance.
MONTH SETTING: Press (B) and the month (1-12) digits appear flashing. Press (C) to
advance.
DATE SETTING: Press (B) and date (1-31) appears flashing. Press (C) to advance.
DAY SETTING: Press (B) and the day appears flashing. Press (C) to advance the day
of the week. MO (Monday), TU (Tuesday), WE (Wednesday), TH (Thursday), FA
(Friday), SA (Saturday) and SU (Sunday.)
12/24 HOUR OPTION; The time may be set to operate normally (hours 1 -12) or on a 24
hour basis (hours 1-24). To set the (12) or (24) hours, Press (B) after setting the Day
and either 12 or 24 will appear on the display. To select 12 or 24, simply press (C) until
the 12 or 24 time indicator appears.
After setting, press (A) to exit the setting mode. All digits (except seconds) will
appear frozen.
(1) You may complete the setting process at any point by pressing (A).
(2) If you wish to set any particular function (alarm, time, calendar) press and hold
A) for three (3) seconds. Then press (B) until that digit(s) appears flashing. Press (C)
to advance that function, then press (A) to complete the setting process.
(3) While setting, press and hold (C) for fast advance. ___
B. MULTI-LAP EVENT TIMING
When timing multMap events, the operating sequence is START/LAP/
STOP / ACCUMULATED-TIME / RESET.
START: Press (E) to start. Run indicator appears and the time counter (Row 3) is
counting.
LAP: To take a lap reading, press (F) the instance the lap is completed. The lap
number and speed appear in Row 2, the time in Row 3. After 15 seconds, the time will
revert to current lap running time. You may select current lap running time instantly
by pressing (B). Continue to press (F) for each lap reading.
LAP COUNT
IS (001)
ILLUSTRATION (A)
ILLUSTRATION (B)
ROW 1
ROW 2
ROW 3
ROW 1
ROW 2
ROW 3
5
0
Z
00 0.000
go i
<?0 3,9 89
CD.'
0
DH
4
"l?
5FEEO CHRONO
gozooogao
501?0 3.9 89
00:00?H'iEi
-MILE INDICATOR
LAP SPEED OF
203.989 MPH
_LAP TIME OF
44.12 SECONDS
- SPEED LAP (001)
_ LAP (002) RUNNING
TIME
Illustration (a) above indicates the display after you have taken a lap reading. It notes
the speed and time of LAP 001. The time will revert to current lap running time after
15 seconds or instantly when you press (B).
Illustration (B) above shows the lap speed of Lap 001 (Row 2) and the running time of
Lap 002 (Row 3). Running time disappears automatically after fifteen (15) seconds.
The speed and time of Lap 002 will appear only after you press (F) the instant Lap 002
is completed.
Visit us on the web at:
www.stopwatches.com
www.robictimers.com