Chamberlain LiftMaster Professional 422LM Owner's Manual

WARNING
SPECIFICATIONS
CAUTION
Output Rating.................................5 Amps 28VAC or DC Max.
Power .........................................................18V to 35V, @ 30ma
RF Frequency ................................................................390MHz
If the power is other than shown in specifications,
Accessory Transformer Model 95 is required. Model 86
Coaxial Cable Kit is also available.
Accessory Transmitters — Series 50, 60 and 80.
Universal receiver Model 422LM can be used to operate two
AVERTISSEMENT
residential garage door openers or entryways with Model
Series 60 code switch remote controls having red indicator
lights, and up to four Model Series 80 "Smart" remote
controls with green indicator lights.
ATTENTION
In general, code switch remote controls are used when
several persons are operating the same device. The code
switches must be set to matching positions in all remote
controls used to operate the same receiver. (Refer to the
instructions included with Series 60 and 80 remote controls).
Both the receiver and the antenna use TV Type F coaxial
connectors. The antenna can be plugged directly onto the
receiver or mounted to a bracket and connected to the receiver
with Model 86 Coaxial Cable Kit, if you need more range.
Select a location for the receiver which allows access to the
terminals and space for the antenna (as far from metal structures
as possible and preferably with the antenna in an upright
position). Fasten the receiver securely with screws through the
two holes provided in the cover flanges.
Garage door opener #1 (without transformer)
Refer to Figure 1 for wiring connections:
Connect 2-conductor bell wire (not provided) to receiver terminal
screws 3 and 4, and to the opener terminal screws used for the
wall push button.
Also, connect bell wire to receiver terminal 2 and opener terminal
screw 3; use a jumper wire to connect receiver terminals 1 and 3.
Garage door opener #1 (with transformer 95)
Refer to Figure 2 for wiring connections:
Connect bell wire to receiver terminal screws 1 and 2, and to
transformer terminals. Also, connect bell wire (not provided) to
receiver terminal screws 3 and 4, and to opener terminal screws
used for wall push button.
Garage door opener #2: Connect white and white/red bell wire
from the receiver to the opener terminal screws used for the wall
button.
Use a screwdriver to pry open the receiver cover, Figure 3.
Re-connect power to the opener and the accessory
transformer, if used.
• Follow code switch remote control instructions, if applicable.
• Select a remote push button to operate opener #1.
• Press and hold the selected remote button. Then press and
release the "smart" button labeled "A" on the receiver. The
adjacent indicator light will FLASH.
•. Release the remote push button. Opener #1 will now operate
when the selected remote control push button is pressed.
Repeat the procedure, using "smart" button "B", with the other
remote push button to program the second opener
Note: If a remote control push button is not pressed within
30 seconds, indicator light adjacent to selected "smart"
button will turn OFF. In that case, repeat the programming.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-2806
114A1790E
LiftMaster 2-Channel Universal Receiver
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is not connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Figure 1
Figure 2
RED
Indicator
Light
GREEN
Indicator
Light
© 2006, The Chamberlain Group, Inc.
All Rights Reserved
WARNING
OWNER'S MANUAL
WARNING
AVERTISSEMENT
AVERTISSEMENT
Receiver
Wall
(Bottom)
Button
1
1
Common
2
2
3
3
4
Transformer 95
Receiver
Wall
(Bottom)
Button
1
1
Common
2
2
3
3
4
RECEIVER
Select a
Push Button
Push
Button
Model 422LM
Operator
Trans
Primary
Relay
24 v
Operator
Trans
Primary
Relay
24 v
Figure 3
Smart
Button
"B"
Smart
Button
"A"