Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Samsung HW-S50B/ZA
Summary of Contents for Samsung HW-S50B/ZA
- Page 1 Repair Guide HW-S50B/ZA Ver.1.0...
- Page 2 Contents 1. Precautions 1-1. Safety Precautions ......................... 1-1 1-2. Servicing Precautions ......................1-3 1-3. Precautions for Electrostatically Sensitive Devices (ESDs) ........... 1-4 1-4. Installation Precautions ......................1-5 2. Disassembly and Assembly 2-1. Disassembly .......................... 2-1 2-1-1. Separate REAR Cover and BOTTOM Cover..............2-1 2-1-2.
- Page 3 Samsung certified service provider will not be covered by the warranty.
- Page 4 Samsung reserves the right, at its sole discretion, to change, modify, add or remove portions of any part of this manual at any time. It is your responsibility to check the manual periodically for changes. Your use of the manual...
- Page 5 Precautions 1. Precautions • Follow these safety instructions while servicing the ESD to prevent damage and to protect against potential hazards such as electrical shock and X-rays. • For continued safety, do not attempt to modify the circuit board. • Disconnect the AC power and DC power jack before servicing. Warning 1-1.
- Page 6 Precautions 5. Insulation Resistance Cold Check: Antenna (1) With the unit’s AC plug disconnected from the AC source, Terminal connect an electrical jumper across the two AC prongs. (2) Set the power switch to ON. Exposed (3) Measure the resistance between the shorted AC plug and Metal Part any exposed metallic parts.
- Page 7 Precautions 1-2. Servicing Precautions • An electrolytic capacitor installed with the wrong polarity might explode. Warning • Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Caution • If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
- Page 8 Precautions 1-3. Precautions for Electrostatically Sensitive Devices (ESDs) • Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs). Examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.
- Page 9 5. Installing the product in a special place like below rather than normal environment may cause serious quality concerns due to its special conditions. If this is the case, make sure to contact a local Samsung service center before installing the product.
- Page 10 Disassembly and Assembly 2. Disassembly and Assembly • As this product has parts that are sensitive to static electricity, be careful when handling them. Warning 2-1. Disassembly • Disconnect the product from the power source before disassembly. • Follow these directions carefully; never use metal instruments to pry apart the cabinet. Caution •...
- Page 11 Disassembly and Assembly 2-1-2. Separate MAIN ASSY KIT • Remove 3 screws and 2 cables. -P/N:AH81-14034A Remark • Separate MAIN ASSY KIT from P-Body. Remark...
- Page 12 Disassembly and Reassembly 2-1-3. Separate MAIN PCB • Remove 2 screws and 2 cables. Separate MAIN PCB from PCB Bracket. Remark -P/N:AH81-14035A...
- Page 13 Disassembly and Assembly 2-1-4. Separate BT Module and Wireless Module • Separate Wireless Module. − Separate Wireless Module. Remark − Remove 1 screw and separate the Wireless Module from the Bracket. − Remove 1 screw and unlock the FFC cable and separate the BT Module from the Bracket.
- Page 14 Disassembly and Assembly 2-1-5. Separate KEY PCB • Remove 8 screws and 2 FFC Cables. Remark -P/N: AH81-09756A Unlock Lock • Separate KEY PCB from P-Body. Remark...
- Page 15 Disassembly and Assembly 2-1-6. Separate LED_IR PCB. • Remove the 12 screws Remark -P/N: AH81-14034A • Pull out the FRONT Cover. Remark • Remove 3 screws and 1 cable. -P/N: AH81-09756A...
- Page 16 Disassembly and Assembly 2-2. Assembly • Assembly procedures are in the reverse order of disassembly procedures. • The exterior may differ depending on the product. Note Description Picture Description Please assemble in reverse order of disassembly steps. ※ Cautions 1. Attach the Wireless module and the cable properly. If the cable is attached reversely, it could burn or damage the module 2.
Need help?
Do you have a question about the HW-S50B/ZA and is the answer not in the manual?
Questions and answers