Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LENCO CS-173 DAB
Summary of Contents for LENCO CS-173 DAB
- Page 1 OWNER'S MANUAL Mobile Audio System PLL Synthesizer Stereo Radio RDS (Radio Data System) operation DAB (Digital Audio Broadcast) Operation Digital Compact Disc Player Automatically Memory Storing Fold Down Full Detachable Panel Preset Equalization Electronic Shockproof (ESP) Function Remote Control...
-
Page 2: Table Of Contents
CONTENTS Installation Pausing playing Previewing all track Take out screw before installation Repeating the same tracks DIN Front-Mount (Method A) playing all track in random Installing the unit Ejecting a disc Removing the unit MP3 operation DIN Rear-Mount (Method B) Switch to CD (MP3) mode Using The detachable Front Panel Ejecting a disc... -
Page 3: Installation
INSTALLATION Notes: TAKE OUT SCREW BEFORE Choose the mounting location where INSTALLATION the unit will not interfere with the Before install the unit, please remove normal driving function of the driver. the two screws . Before finally installing the unit, Take out screw connect the wiring temporarily and before installation... -
Page 4: Removing The Unit
INSTALLATION middle left and right sides of the unit. Then use the supplied hardware Then slide the sleeve off the back of (Tapping Screw (5x25mm) and Plain the unit. Washer) to attach the other end of metal strap to a solid metal part of the Sleeve L Key vehicle under the dashboard. -
Page 5: Din Rear-Mount (Method B)
INSTALLATION 2. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm)on each side. Note: the outer trim ring, sleeve and the metal strap are not used for method B installation. DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. -
Page 6: Using The Detachable Front Panel
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Install the Front Panel 1. Press the OPEN button, the front panel 1.When the metal plate is folded down, will slide down. insert the front panel into the metal plate then push them into the main body. -
Page 7: Wiring Connection
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE IGNITION SWITCH (ACC+) FUSE MEMORY YELLOW BACK-UP (B+) BLACK GROUND (B-) (GREY) Rch RED REAR RCA CABLE POWER BLUE ANTENNA Lch WHITE WHITE GREY FRONT Lch FRONT Rch SPEAKER SPEAKER WHITE/BLACK GREY/BLACK GREEN VIOLET REAR Lch REAR Rch... -
Page 8: Operation
OPERATION LOCATION OF KEYS... -
Page 9: Switching On/Off The Unit And Illumiating
OPERATION When this mode is selected, any SWITCHING ON/OFF THE UNIT AND automatic retune mode is not ILLUMINATING activated. Only double beep sound Switch on the unit by pressing any button (ALARM) is output. (except OPEN button (7) and EJECT When newly tuned station does not button (4)). -
Page 10: Loudness
OPERATION all allowed double key is pressed to next same PI station. long (1 sec). When same PI station does not catch e.g. 1 cyclic search, the radio goes to last When preset button (14) is pressed. station and waits for several minutes When BND/LOU button (13) is until PI code is received. -
Page 11: Vacuum Fluorescent Display
OPERATION VACUUM FLUORESCENT DISPLAY SELECTING STATION Exhibit current frequency and activated Press MANU/SKIP button(16) functions on the display (23). or button MANU/SKIP (17) FLASHING LED shortly to activate automatic seek If the front panel does not install in the function. Press for several seconds main unit, the LED (12) will be flashing. -
Page 12: Rds (Radio Data System) Operation
OPERATION PTY switch is shared as follows: RDS (RADIO DATA SYSTEM) OPERATION PTY MUSIC group PTY SPEECH group PTY off - Setting RDS mode Press AF button (3) and release immediately to switch on or off RDS According to above 2 allotted group, mode. -
Page 13: Dab (Digital Audio Broadcast)
OPERATION Identification data showing traffic EON TA LOCAL/EON TA information is being transmitted DISTANCE mode. or not The purpose of this key is to reduce EON: Enhanced Other Networks unwanted EON TA switching, which Information EON TA information was received Broadcasting information on PI, from current station and the radio AF, TP, TA, etc, relating to... -
Page 14: Cd Operation
OPERATION 6 PRESET KEY fast reverse of fast forward, CD play LOAD FROM MEMORY AND starts from when you release the SAVE TO MEMORY PLAY button. MODE CHANGE (6) RADIO-> DAB-> S-CDP-> RADIO PAUSING PLAYING (1) RADIO Press PAU button (19) to pause CD 1) FM1 player, Press it again to resume play. -
Page 15: Ejecting A Disc
OPERATION EJECTING A DISC M1-M6, MOD (7), MANU/SKIP When the front panel is sliding down, DOWN(8), MANU/SKIP UP (9), press EJECT button (4) to stop CD DSP(0). playing and eject the disc from the If selected three digits, the unit disc slot (5). -
Page 16: Display Information
OPERATION desired directory/songs by using KEY Assigned IN Searching mode (Table 1) MANU/SKIP UP/ DOWN button and BND/LOU (ENTER) button to Mode Select confirm. If the selected title is a BND/LOU ENTER song, it starts to play. If the selected title is a directory A, B, C, 1 name, display will show (' '), then D, E, F, 2... -
Page 17: Disc Notes
OPERATION C. Notes on MP3 files (MP3 Version DISC NOTES Only): A. Notes on discs: 1. The disc must be in the ISO9660 level 1. Attempting to use non-standard 1or level 2 format, or Joliet or Romeo shape discs (e.g. square, start, heart) in the expansion format. -
Page 18: Specification
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 165 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) 10 dB - Treble (at 10 kHz) 10 dB Maximum Output Power : 4x40 watts Current Drain : 15 Ampere (max.) -
Page 19: Trouble Shooting
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on.