Page 1
Monitor Service Manual Model: MB16AWP Version no.: 0 Release date: 2024/4/8...
Page 2
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
1. Safety Precautions FOR PRODUCTS CONTAINING LASER: DANGER- Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. CAUTION- Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION- The use of optical instruments with this product will increase eye hazard. TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL...
3. Disassembly and Assembly Procedures 3.1 Disassembly SOP Preparation before disassemble 1. Clean the room for disassemble 2. Identify the area for monitor 3. Check the position that the monitors be placed and the quantity of the monitor; prepare the area for material flow; according to the actual condition plan the disassemble layout 4.
Page 7
Remove the Bezel. 1. Remove ABSORBING PAD. 2. Remove AL-foil tape and disassemble MAIN BOARD eDP cable from Main Board. 3. Remove all tapes then remove wire from Main Board. 4. Remove tape then remove Speaker wire ANTENNA_01/02 MAIN BOARD Board wires from Main Board.
Page 8
1. Disassemble screw *1 to remove Key Board1 and remove tape from Battery then remove Key Board1. Screw P/N: 8F.5A422.2R4 (#SCRW TP-B FPH M2*2.4L ZN ) Torque: Screw 1.2±0.5K driver g-cm 2. Disassemble screw *1 to remove Key Board2. Screw P/N: 8F.5A422.2R4 (#SCRW TP-B FPH M2*2.4L ZN )
Page 9
1. Disassemble Power Board by screw *5pcs then remove Power Board & Battery from Rear Case. POWER BOARD Screw P/N: 8F.8A352.2R0 (#SCRW M FPH M2*2L( 6/.4)BZN NY ) Torque: 3.0±0.5K MAIN BOARD g-cm 2. Pull the tape then remove the adhesive Battery then can remove POWER BOARD...
Page 10
1. Tear off 2 tapes from WIFI ANTENNA_01 /02 BD then remove WIFI ANTENNA_01 /02 BD. 1. Dissemble Speaker on the top side of BKT-Main Rear Case by screw *4. Screw P/N: Torque: 8F.8A352.2R0 Screw 3.0±0.5K (#SCRW M FPH M2*2L( driver g-cm 6/.4)BZN NY )
3.2 Assembly SOP Preparation before assemble 1. Clean the room for work 2. Identify the area for material 3. Prepare the implement, equipment and materials as bellow: 1) Working table 2) Screw-driver 3) Glove 4) Cleaning cloth 5) ESD protection After unplugging the power cord, the power Board still have power energe.
Page 12
4. Stick WIFI ANTENNA_01 BD and put into the ribs of top side of rear cover. 5. Brone-Foil needs to be sticked on the BKT-main 2. Assemble Speaker on the top side of BKT-Main Rear Case by screw *4. Torque: Screw P/N: Screw 8F.8A352.2R0...
Page 13
1. Insert wire of battery into POWER connector of Power BOARD BD then paste yellow tape*1 on the connector. POWER 2. Paste the acetate BOARD tape *1. POWER BOARD 3. Insert FFC Cable into connector of Power BD. 1. Release the adhesive of mylar.
Page 14
3. Align the edges of Power BD, stick mylar*1 on the POWER BOARD Power BD. 1. Put PWR BTN BD on the bottom-left of Rear Case and fix it by screw*1. Screw P/N: 8F.5A422.2R4 (#SCRW TP-B FPH M2*2.4L ZN ) 2.
Page 15
1. Insert e-DP to panel connector and fix by yellow tape*1. 2. Align the edge of right and left side of panel and stick the sponge*2 3. After sticking sponge, the distance between sponge and the edge of bottom side of panel must be 74~...
Page 16
1. Release the adhesive of bezel. 2. Assembling the bezel to the set.
Need help?
Do you have a question about the MB16AWP and is the answer not in the manual?
Questions and answers