Nokia 108, 108 DS Manual
Also See for 108:

Advertisement

Nokia 108, 108 DS Manual

Exploded view

Exploded view

Disassembly steps

  1. For disassembling you need the Nokia Standard toolkit version 2.
    Note that the device used in this disassembly procedure is the dual SIM variant, RM-944. All the disassembly steps are the same for both single and dual SIM variants.
    Disassembly steps - Step 1
  1. Protect the A-COVER window with protective film.
    Disassembly steps - Step 2
  1. To detach the B-COVER press the CAMERA BEZEL and then pull the B-COVER with fingers. Remove the B-COVER.
    Disassembly steps - Step 3
  2. If there is a BATTTERY remove it also.
    Disassembly steps - Step 4
  1. Unscrew the four Torx+ size 4 screws in the order shown.
    Disassembly steps - Step 5
  2. To rseparate the D-COVER and the A-COVER, first release the shown clips on the right side with the SRT-6.
    Disassembly steps - Step 6
  1. Use the SRT-6 to release the clips on the bottom side.
    Disassembly steps - Step 7
  2. Then release the clips from the left side of the device.
    Disassembly steps - Step 8
  1. Lift the bottom end of the A-COVER and release the clips on the top side.
    Disassembly steps - Step 9
  2. The D-COVER and the A-COVER can now be separated.
    Disassembly steps - Step 10
  1. Protect the DISPLAY with protective film.
    Disassembly steps - Step 11
  2. Protect the other side of the A-COVER window with protective film.
    Disassembly steps - Step 12
  1. Push out the KEYMAT from the A-COVER.
    Disassembly steps - Step 13
  2. To detach the ENGINE BOARD, first release this clip located near the guiding hole with the SS-93.
    Disassembly steps - Step 14
  1. Then release the shown clip with the SS-93.
    Disassembly steps - Step 15
  2. Continue by releasing the clip near the guiding hole from the left side of the device.
    Disassembly steps - Step 16
  1. Then release the shown clip.
    Disassembly steps - Step 17
  2. To separate the ENGINE BOARD including the UI SHIELDING lift the bottom end first and then remove it.
    Disassembly steps - Step 18
  1. Lift up the HEADSET JACK with fingers.
    Disassembly steps - Step 19
  2. Lift up the DC JACK with fingers.
    Disassembly steps - Step 20
  1. Use the sharp end of the SS-93 to release the SPEAKER. Use tweezers to remove the SPEAKER. Do not use it again. Discard it.
    Disassembly steps - Step 21
  2. Use the sharp end of the SS-93 to remove the SPEAKER GASKET. Do not use it again. Discard it.
    Disassembly steps - Step 22
  1. Release the clips holding the UI SHIELDING on the ENGINE BOARD.
    Disassembly steps - Step 23
  2. Remove the UI SHIELDING.
    Disassembly steps - Step 24
  1. Use the dental tool to release the EARPIECE.
    Be careful not to injure yourself with the sharp end of the dental tool.
    Disassembly steps - Step 25
  2. Remove the EARPIECE and the EARPIECE ADHESIVE with tweezers. Do not use them again. Discard them.
    Disassembly steps - Step 26
  1. Open the CAMERA connector with the SS-93.
    Be careful not to damage the connector or any components nearby.
    Disassembly steps - Step 27
  2. Use the SS-93 to carefully loosen the adhesive holding the CAMERA.
    Disassembly steps - Step 28
  1. Remove the CAMERA with tweezers.
    Disassembly steps - Step 29
  2. Use the SS-93 to release one corner of the DOMESHEET. Peel off the DOMESHEET with fingers. Do not use it again. Discard it.
    Disassembly steps - Step 30
  1. The Nokia 108, Nokia 108 Dual SIM disassembly procedure is complete.
    Disassembly steps - Step 31

Assembly hints

  1. Align the CAMERA with tweezers. Use the shown clips as references. Close the CAMERA connector with the SS-93. Be careful not to damage the connector or any components nearby.
    Assembly hints - Step 1
  2. First place the top end of the ENGINE BOARD including the UI SHIELDING into the D-COVER. Then lower down the bottom end.
    Assembly hints - Step 2
  1. While attaching the ENGINE BOARD including the UI SHIELDING make sure you do not press the DISPLAY.
    Assembly hints - Step 3
  2. Attach the top end of the A-COVER first. Then put down the bottom end and make sure all the clips are secured.
    Assembly hints - Step 4
  1. Fasten the four Torx+ size 4 screws in the order shown to the torque of 13 Ncm.
    Assembly hints - Step 5

Solder components

TOP
Solder components - TOP

BOTTOM
Solder components - BOTTOM

Service devices

CA-101 Service cable

AC-11 Travel charger

SF-320 Flash adapter

Nokia Standard Toolkit (v2)
Supplier or manufacturer contacts for tool re-order can be found in "Recommended service equipment" document on Nokia Online.

Product controls and interfaces

Product controls and interfaces

  1. Charger connector
  2. Flashlight
  3. 3.5 mm AHJ connector
  4. Earpiece
  5. Display
  6. Left selection key
  7. Call key
  8. Scroll key
  9. Right selection key
  10. End/Power key
  11. Keypad
  12. Microphone
  13. Camera
  14. Antenna area

Service concept

Flashing concept
Flashing concept

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Nokia 108, 108 DS Manual

Advertisement

Need help?

Need help?

Do you have a question about the 108 and is the answer not in the manual?

Questions and answers

Table of Contents