Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Embention Veronte R12S
Summary of Contents for Embention Veronte R12S
- Page 1 R12S Hardware Manual Release 3.0 Embention 2024-12-05...
-
Page 3: Table Of Contents
CONTENTS 1 Introduction 2 Quick Start Warnings ..........3 Technical Mechanical Specifications . - Page 5 R12S Hardware Manual, Release 3.0 Veronte R12S is an OEM miniaturized DC-DC converter with redundancy available. Warning: Select your version before reading any user manual. The following image shows where to select a version from any Embention user manual. CONTENTS...
- Page 6 R12S Hardware Manual, Release 3.0 CONTENTS...
-
Page 7: Introduction
CHAPTER INTRODUCTION Fig. 1: R12S Veronte R12S is a redundant DC-DC converter with different output voltage options that user can choose with a switch: 3.3, 5, 6, 7.4, 9 or 12 V. - Page 8 R12S Hardware Manual, Release 3.0 Chapter 1. Introduction...
-
Page 9: Quick Start
CHAPTER QUICK START This user manual covers the assembly of Veronte R12S. To use it, weld input and output wires mechanical electric according to the section, then fix it to the assembly frame with two M3 screws. Pinout Fig. 1: Input and output diagram 2.1 Warnings... - Page 10 R12S Hardware Manual, Release 3.0 Chapter 2. Quick Start...
-
Page 11: Technical
CHAPTER THREE TECHNICAL 3.1 Mechanical Specifications • Temperature range: -40 to 85 °C. • Weight: 19 g. 3.1.1 Dimensions 3.2 Electrical Specifications Property Value Input voltage range 5.5 to 36 V Output continuous current Output peak current Enclosure protection IP 66 Output voltages Choose between: 3.3, 5, 6, 7.4, 9 or 12 V... - Page 12 R12S Hardware Manual, Release 3.0 Chapter 3. Technical...
-
Page 13: Hardware Installation
CHAPTER FOUR HARDWARE INSTALLATION 4.1 Mechanical assembly M3 screws are recommended for mounting. In saline environments such as coastal and oceanic, the screw material must be stainless steel. Fig. 1: R12S assembly... -
Page 14: Electrical
The output voltage can be chosen between 3.3, 5, 6, 7.4, 9 or 12 V. Nonetheless, the input must be higher than the desired voltage (but not higher than 36 V or lower than 5.5 V), since Veronte R12S cannot obtain more voltage than supplied. -
Page 15: Redundancy
R12S Hardware Manual, Release 3.0 This pad allows users to enable or disable the voltage output of the Veronte R12S, allowing connected subsystems to be turned ON or OFF from the Veronte Autopilot 1x GPIO outputs. • Setting the GPIO connected to “E” to LOW Enables the output voltage (Vout) •... - Page 16 R12S Hardware Manual, Release 3.0 Chapter 4. Hardware Installation...
-
Page 17: Maintenance
CHAPTER FIVE MAINTENANCE Apart from cleaning, no extra maintenance is required to guarantee the correct operation of Veronte R12S. In order to clean R12S properly follow the next recommendations. • Turn off the device before cleaning. • Use a clean, soft, damp cloth to clean the unit. - Page 18 R12S Hardware Manual, Release 3.0 Chapter 5. Maintenance...
-
Page 19: Acronyms And Definitions
CHAPTER ACRONYMS AND DEFINITIONS DC-DC Direct Current to Direct Current... - Page 20 R12S Hardware Manual, Release 3.0 Chapter 6. Acronyms and Definitions...
-
Page 21: Contact Data
This platform facilitates communication and ensures traceability of all support requests, helping us to address your needs efficiently. For other questions or general inquiries, you can reach us via email at sales@embention.com or by phone at (+34) 965 115 421...
Need help?
Do you have a question about the Veronte R12S and is the answer not in the manual?
Questions and answers