Advertisement
Quick Links
High-Efficiency Automatic Backwash Disk Prefilter
1. Main Application
Used for filtering municipal water treatment. It belongs to coarse filtration. Can filter PM larger than
0.05mm, for protecting the back water equipment.
2. Product Characteristics
3. Technical Parameters
Model
Nominal Size
RL-Q02
Operating Conditions:
Working Pressure: 0.1~0.6MPa
Environment Temperature: 4~40℃
Power Adapter: Input AC100~240V/50~60Hz, output DC12V.
4. Check the Spare Parts
When unpacking the product, please check below spare parts.
No.
Description & Specification
1
2
User Manual
Rated Water Flow Rate
DN25
Prefilter
Fixed Seat
0WRX.466.740
Rev.A.2008
Filtration Precision
2.5 m
3
/h
Working Water Temperature: 5~30℃
Relative Humidity: ≤95% (25℃)
Quantity
1
1
Remark
50μm
Appearance B
Remark
Advertisement
Related Manuals for Runxin RL-Q02
Summary of Contents for Runxin RL-Q02
- Page 1 0.05mm, for protecting the back water equipment. 2. Product Characteristics 3. Technical Parameters Model Nominal Size Rated Water Flow Rate Filtration Precision Remark RL-Q02 DN25 2.5 m 50μm Appearance B Operating Conditions: Working Pressure: 0.1~0.6MPa Working Water Temperature: 5~30℃ Environment Temperature: 4~40℃...
- Page 2 Expand Screw Seal Ring Soft Pipeline Clamp Connector Transformer Leakage Sensor (optional) 5. Product Appearance and Installation Dimensions...
-
Page 3: Installation Notes
6. Installation Notes 1. Installation conditions should conform to the requirements of the product work environment. 2. It should be installed behind water meter, but in front of other equipment. 3. It should stay away from hydrops, no exposure to rain or sunlight. 4. - Page 4 3. Parameter Setting The prefilter parameter settings of this model are divided into: 1). Parameter setting. 2). Protection parameter settings. Among them, the water leakage protection parameter setting can be set according to the actual situation of the user, and the function can be turned off if not necessary.
- Page 5 b. Set Rinsing Time Press the button under the unlocked figure B1 and then press to select "Set Rinsing Time" as figure B2. Then press to enter into rinse time setting interface as figure B3. When hour value flashes in figure B3, press to set the hour value.
- Page 6 c. Set Residual Water Setting residual water means that when the treated water reaches a certain amount, when the current time is the same as the rinsing time, the system enters the rinsing status. The setting of this parameter depends on the local water quality. Press the button under the unlocked figure C1 and then press to select "Set...
- Page 7 machine automatically closes the water inlet and displays it on the display board. Leakage Protection of Continuous Water Supplying Setting method: Press the button under the unlocked figure D1 and then press to select "Set Cont. Water Time" as figure D2. Then press to enter into continuous water time setting interface as figure D3 or D4.
- Page 8 e. Peak F.R. for Close When the machine detects that the instantaneous flow of the water outlet reaches the set value, the machine automatically closes the water inlet and displays it on the display board. Leakage Protection of Instantaneous Flow Setting method: Press the button under the unlocked figure E1 and then press to select...
- Page 9 f. Query Menu In order to facilitate user settings, the machine provides two historical water consumption query parameters. After use water for a period of time, the user can query the maximum water consumption time and the maximum water flow rate, which is more convenient for the user to set the water leakage protection function.
- Page 10 8.2 Manual Close When it is necessary to maintain the filter element or other water appliances, the water source can be cut off by the manual close function. In the unlocked status, press and hold for 5 seconds to automatically switch to the closed status. To return to service status, press and hold for 5 seconds.
-
Page 11: Troubleshooting
lift the close status, press and hold for 5 seconds to automatically switch to the service status (The close status caused by the leakage sensor needs to solve the water leakage first). 8.5 LED Lamp Touch any button, the LED lamp will light for 5 minutes. Without any operation in 5 minutes, the light will be off. - Page 12 1. Inlet water pressure is low. 1. Install booster pump or Ineffective 2. Fixed seat of filter cartridge gets increase flow. backwash stuck. 2. Disassemble and clean the filter cartridge. Continuous water supplying is too Reset closing time for long. continuous water supplying according to water usage.
Need help?
Do you have a question about the RL-Q02 and is the answer not in the manual?
Questions and answers
Здравствуйте. У меня RL Q02, работает более месяца, все нормально, но последние несколько дней перестал показывать расход воды из за этого не срабатывает промывка фильтра. В чем дело?
The issue with the Runxin RL-Q02 not displaying water consumption and not triggering the filter backwash could be due to one or more of the following:
1. Wire of water meter is disconnected or damaged – Reconnect or replace the wire of the water meter.
2. Turbine is stuck – Clean or replace the turbine.
3. Display board is damaged – Replace the display board.
4. Controller wire is loose – Reconnect the controller wire to the locating board.
5. Locating board is damaged – Replace the locating board.
These problems can prevent the system from detecting water flow and initiating backwash.
This answer is automatically generated