Table of Contents
Advertisement
Quick Links
The Whole House Water Filter
Please read this manual in details before using the device and keep it properly in order to
consult in the future.
Note: The design and specifications are subject to the changes without prior notice. We reserve
the right of interpretation to the user manual.
J50
J60
J120
J150
J180
User Manual
0WRX.466.571
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Runxin J50 Series
Summary of Contents for Runxin J50 Series
- Page 1 The Whole House Water Filter J120 J150 J180 User Manual Please read this manual in details before using the device and keep it properly in order to consult in the future. Note: The design and specifications are subject to the changes without prior notice. We reserve the right of interpretation to the user manual.
- Page 2 Catalogue Preface ........................1.Product Profile ......................2.Working Principle ..................... 3. Assembly & Parts ....................4.Specification & Active Carbon Volume ..............5. Application Range ....................6. Technical Parameters ....................6.1 Parameter Table ....................6.2 Working Condition ....................7. Function and Characteristics ................... 8.Installation ........................
-
Page 3: Working Principle
Preface Thanks for choosing our products. The whole house water filter series products are featured by reduction of residual chlorine and other impurity things. It can meet the demand of daily laundry, bath, cleaning and provide drinking water with high quality for organization, school, group, etc. In order to correctly install, set, use and maintain products, please do read the manual in details and strictly follow the steps to install and use the products. -
Page 4: Assembly & Parts
3. Assembly & Parts Description Description Automatic Multi-port Valve Active Carbon FRP Tank Strainer Riser Pipe Quartz Sand 4.Specification and & Active Carbon Volume FRP Tank Size Active Carbon Quartz Sand Model FRP Tank Model (Φ*h)mm Volume L Volume L RL-J50 258*330 1013... -
Page 5: Technical Parameters
5.Applicaton Range Tap water or other water source which meet the requirement for whole house water filter. 6. Technical Parameters 6.1Parameter Table Rated Service Flow Rate of Products Approval Water Treatment Capacity Working Pressure Model Related to Drinking Water RL-J50 RL-J60 RL-J120 1200... - Page 6 generated by iron, manganese or plant. ●Dechloridation: Remove the stink which is caused by disinfector in drinking water (Residual chlorine). ●Remove TOC: Remove 10-60% of organic pesticide, insecticide, chlorinated hydrocarbon, etc. ●Remove heavy metal: Such as Hg, Cr, etc. ●Remove synthetic detergent and dyestuff. ●Remove virus.
- Page 7 ※Make sure a check valve is equipped between the device and water heater when a heating stove or water heater is connected behind the device, in case of hot water reflux and damage the inner system of the product. ※Separate sewer line for the device is required. 5 to 10cm clearance must be maintained between the drain pipe and floor drain, in case of siphon and cause valve damage by the waste water.(Installation refer to below picture) ※Before installing the pipeline, please clean the residual impurity and dust in the pipeline.
- Page 8 Illustration: Install two three-way ball valves to connect the control valve and inlet/outlet pipeline. The valve B is connected with the inlet of the control valve; the valve A is connected with the outlet of the control valve. When repair the tank, adjust the valve A and B to make the inlet connected with outlet directly, so the water do not pass through the valve;...
- Page 9 ※Control valve should be higher than sewer. The length of drain line should be similar to the height of tank. Insert the drain line to the floor drain, but not to the bottom. Leave about 5-10mm distance between the end port of drain line and sewer. ※Each pipeline should be supported with fixed holder independently, avoiding the control valve be damaged by bearing the gravity from the pipeline.
- Page 10 Button lock indicator ● Lights on, indicating the buttons are locked. At this moment, press any single button will not work (No operation in one minute, will light on and lock the buttons.) ●Solution: Press and hold both for 5 seconds until the lights off.
- Page 11 Process Display ①User Mode After power on, the following interface will show 3 seconds, and then enter into user mode. **************** Residential Valve Type **************** ②F67D process display 12:30:25 02:08:00 02:17:25 System in Service In Backwashing… In Fast Rinse… Motor Running… Remaining: 3 min.
- Page 12 value. and hear a sound “Di”, then 4．Lastly, press finish adjustment. and enter into the interface of ”Filter 1．Press Filter Para.” ,as the figure J1 shows. and select the item of “ Set Rinsing 2．Press Set Filter Para. Time”; Then press , the setting interface will show Set Time of Day as the figure J3;...
- Page 13 Set Fast Rinse 3Min. B. Parameter set in background Parameters could be set in background: Set Mode, Set Valve Model, Set Service Days, Set Backwash, Set Fast Rinse(For water filter setting) a) In the H1 interface, select the “Mode” and press , as the figure A1 shows.
- Page 14 RL-J60 RL-J120 RL-J150 RL-J180 ※Flow Chart 9. Usage Illustration After installing the device and setting the relevant parameters, please conduct the trial running as follows: Switch on power. Press and go in the Backwash status; adjust the bypass valve (Three-way valve A and B) to service position, slowly open the inlet valve.
-
Page 15: Troubles Shooting
10. Notice Before reading and understanding the manual instruction, please do not operate the device. 10.1 Forbid installing the device near heat source or take anti-heat protective measures when install near the heat source. It is also forbidden to connect the device with the hot-water pipeline or the pipeline with the possibility of hot-water returning. - Page 16 E. Adjust the rinsing time. A. Set the correct the regeneration 3. Regeneration too A. Regeneration cycle set cycle depending on the raw water often or less. incorrect. quality and usage of end-user. A. Air in water system. A. Assure that well system has flow rate Loss...
-
Page 17: Maintenance
A. Hall component on locating board is damaged. B. Wiring of locating A. Replace locating board. 10. E2 Flashes board with control board is B. Replace wiring. damaged. C. Replace control board. Control board damaged. Control board 11. E3 or E4 Flashes A. - Page 18 ※When guarantee period is expired, we will still provide after-sales service, such as maintenance, changing media, supplying parts, etc. The fee of materials and service will be charged according to our latest charging standards. ※It couldn’t be repaired free of charge under the below conditions: ①Media, seal, decoration shell, the coating of appearance, etc.
Need help?
Do you have a question about the J50 Series and is the answer not in the manual?
Questions and answers