Braun CareStyle 5 (12850020) Manual

Braun CareStyle 5 (12850020) Manual

Also See for CareStyle 5:

Advertisement

Braun CareStyle 5 (12850020) Manual

Description

Description

1a On/Off button
1b Iron LED

  1. Mode button
  2. FastClean system icon
  3. Water reserve icon

5+6 Steam setting icons

  1. Heel rest
  2. Steam button
  3. Iron rest
  4. Lock system
  5. Removable water tank
  6. Double cord / storage
  7. Descaling valve
  8. Power cord / storage

Intended use
The appliance must be used only for ironing garments which are suitable for ironing according to the care label. In addition the appliance can be used for refreshing. Never iron or dampen garments while wearing them.

Before first use
When steam is ready for the first time we recommend to iron for a few minutes over a rag to avoid manufacturing residues can dirty your garments.

Filling the water tank

Make sure that the appliance is switched off and the system is unplugged.
 Filling the water tank

  • Remove the water tank (11).
  • Fill the water tank with tap water, taking care not to exceed the "max" level but at least up to the mark "min". If you have extremely hard water, we recommend that you use a mixture of 50% tap water and 50% distilled water.
  • Never use distilled water exclusively. Do not add any additives (e.g. starch). Do not use condensation water from a tumble dryer.
  • Insert the water tank.
  • Place the appliance on a stable, level surface.

information Note: If you use filtering devices or in-house permanent descaler, make absolutely sure the water obtained is neutral ph.

Water reserve function

Water reserve function
When the water level is becoming low, the water reserve icon (4) starts flashing. At this stage it is possible to continue steam ironing for about 10-15 minutes.

When the water reserve icon turns permanently on, it becomes necessary to refill the water tank. To continue steam ironing, refill the water tank at least up to the mark "min".

Start into operation

Start into operation
Before start ironing follow the garment care label instructions carefully. Fabrics with this symbol are not ironable.

Place the iron on the iron rest (9) or on its heel rest (7), unwind completely both cords, plug in the appliance and press the On/Off button (1a).

The iCare setting and the iron LED (1b) start flashing. The iron will start to heat up.

Once the temperature is reached, the iron LED and the related steam setting icon turn permanently on and you hear an acoustic signal indicating steam is ready.

Steam ironing

Press the steam button (8) to release steam.

Dry ironing

Iron without pressing the steam button (8). Please note that after 10 minutes of dry ironing, the iron switches to the stand-by mode. After additional 10 minutes the auto off mode is activated.

Steam shot function

Press the steam button (8) twice in quick succession. There will be a continuous steam emission for a few seconds. Press the steam button once again during steam emission to stop the function.

Settings

Settings
When the appliance is switched on, it will always be set to the iCare setting, independently on the last setting chosen. To switch from one setting to another, press the mode button (2).

Eco

It is suggested for most delicate garments like synthetics, silk and blended fabrics. This setting allows less power consumption.

iCare

It is suggested for garments like wool, polyester and cotton.

Turbo

It is suggested for garments that need more powerful steam, like thick cotton/ linen and jeans.

This setting can also be used to refresh and sanitize garments that were in the closet before dressing.

information Note: Do not use the sanitize function on people and pets.

Vertical steam

The iron can also be used for steaming hanging clothes. Hold the iron in a vertical position. Press the steam button (8) while moving the iron from top to the bottom.

burn hazard
steam is very hot. Never iron or dampen garment while wearing them.

Ergonomic certification


This unit, assessed and certified by an Ergonomics Certifying Institute has been ergonomically designed, for effortless ironing and excellent results fulfilling the ergonomic requirements belonging to Polytechnical, Biomedical, Psychosocial (usability) and Human Centered Design Process area.

Real users have been actively involved in all phases of product design and in testing process to get a more satisfying experience.

Follow the below recommendations, for an effortless and more comfortable ironing experience:

  • Before starting your ironing session, it is recommendable to self-adjust your ironing board in order to reduce shoulders bad postures. The ideal position should allow a 90° angle for your elbow so that your shoulders and back can freely move.
  • It is mandatory emptying the water tank before transporting the unit and making sure not to overly bend your back while lifting it.

Auto Off

Auto Off
This function is activated if after 10 minutes there has been no steam emission.

  • When the iron is in the auto-off mode, the iron LED (1b) and the icon related to the selected setting start flashing.
  • To continue ironing, press any button and wait until the related icon for the setting is permanently on.
  • After additional 10 minutes without steam emission, the iron and the steam station turn off.

Descaling

Descaling
Never open or touch the descaling valve (13) when the appliance is hot and/or plugged in.

Do not use any chemicals, additives or descaler to rinse the boiler.

When the system needs to be decalcified the FastClean system icon (3) starts flashing.

To perform the descaling take the following steps:

  • Switch off (1) and unplug the appliance. z Empty the water tank.
  • Wait until the appliance has cooled down (minimum 2.5 hours).
  • Place the appliance on the edge of the sink and turn the descaling valve (13) anticlockwise to open it. Let the water flow into the sink.
  • Clean the descaling valve under running water to remove the scale formations.
  • When no more water comes out of the appliance screw the descaling valve clockwise to close the boiler.
  • Plug in and switch on.

information Note: If you use an installed in-house permanent descaler, it is recommended to descale the system after every 4 complete tank refills or at least once per month. Please note that in this case the FastClean icon will not automatically turn on.

After ironing

Care & Cleaning

Care & Cleaning
After every ironing session remove and empty the water tank.

  • Before cleaning, always make sure that the appliance is switched off, unplugged and has cooled down completely.
  • To clean the soleplate and the soft material on the handle it is suggested to use a damp cloth.
  • Never use chemicals, vinegar or scouring pads (eg. sponges with coarse nylon fabrics etc).

Lock system

Lock system
The appliance is equipped with a lock system for convenient transportation and easy storage. It is possible to lift and carry the appliance on the handle of the locked iron.

information Note: Before transportation make sure the iron is properly locked and the water tank is empty.

  • Place the soleplate into the recess on the iron mat.
  • To lock the iron push the slider (10) (easy lock) toward the iron until you hear a "click".
  • To unlock the iron push down the button on the slider (easy lock). The iron will be released.

Storage

Storage
Unplug, empty the water tank and let the appliance cool down before winding the cords for storage. For a convenient storage of the power cord also refer to „Ergonomic Certification".


Warranty and Service

For detailed information see separate warranty and service leaflet or visit www.braunhousehold.com.

Troubleshooting Guide

Problem Solution
Steam comes out under the base unit. Turn the appliance off immediately and contact an authorized Braun Customer Service.
Brown coloured fluid leaks from the soleplate. Never pour products into the water tank. Clean the soleplate with a damp cloth and rinse the boiler.
The first time the appliance is turned on, you notice smoke or smell. This is normal and will stop when you have used the iron a few times.
The appliance emits an intermittent noise associated with vibrations. This is normal and no action is needed.
The descaling valve is difficult to unscrew.

Turn the cap forcefully. To avoid the problem, descale the system frequently.

Never open the descaling valve if the boiler is still under pressure or hot. Wait at least 2.5 hours before opening the descaling valve.

After refilling the water tank, the icon does not reset. Empty the water tank, rinse out and refill. Position the water tank correctly.
After performing the boiler cleaning, the icon does not reset. Manually reset the icon:
  • Switch on the appliance
  • Keep pressed the On/Off button for 5 seconds.
Steam setting icon is permanently on, but there is no steam emission from the soleplate.

Turn off and unplug the appliance. Remove and empty the water tank, rinse out and refill. Insert the water tank. Wait until the appliance has cooled down (min 2.5 hours) then try again.

If the problem is still present, contact an authorized Braun Customer Service.

The double cord gets hot during use.

This is normal. It is caused due to the steam passing through the cord during ironing.

Place the double cord on the opposite side so that you cannot touch the cord during ironing.

In case it is damaged, contact an authorized Braun Customer Service.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Braun CareStyle 5 (12850020) Manual

Advertisement

Need help?

Need help?

Do you have a question about the CareStyle 5 and is the answer not in the manual?

Questions and answers

Table of Contents