SMC Networks TigerStack II SMC8848M Installation Manual
  1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Switch
  5. TigerStack II SMC8848M
  6. Installation manual

SMC Networks TigerStack II SMC8848M Installation Manual

Gigabit ethernet switch
Hide thumbs Also See for TigerStack II SMC8848M:
Table of Contents

Advertisement

Quick Links

TigerStack II
10/100/1000
Gigabit Ethernet Switch
24/48 auto-MDI/MDI-X 10/100/1000BASE-T ports
4 RJ-45 ports shared with 4 SFP transceiver slots
2 10GBASE extender module slots
Non-blocking switching architecture
Support for a redundant power unit
Spanning Tree Protocol, RSTP, and MSTP
Up to 32 LACP or static 8-port trunks
Layer 2/3/4 CoS support through eight priority queues
Layer 3/4 traffic priority with IP Precedence and IP DSCP
Full support for VLANs with GVRP
IGMP multicast filtering and snooping
Manageable via console, Web, SNMP/RMON
Security features: ACL, RADIUS, 802.1x
Supports IPv4/IPv6, dual protocol stack

Installation Guide

SMC8824M
SMC8848M

Advertisement

Table of Contents
loading

Related Manuals for SMC Networks TigerStack II SMC8848M

Summary of Contents for SMC Networks TigerStack II SMC8848M

  • Page 1: Installation Guide

    Layer 3/4 traffic priority with IP Precedence and IP DSCP Full support for VLANs with GVRP IGMP multicast filtering and snooping Manageable via console, Web, SNMP/RMON Security features: ACL, RADIUS, 802.1x Supports IPv4/IPv6, dual protocol stack Installation Guide SMC8824M SMC8848M...
  • Page 3 TigerStack II 10/100/1000 Installation Guide From SMC’s Tiger line of feature-rich workgroup LAN solutions 38 Tesla Irvine, CA 92618 February 2006 Phone: (949) 679-8000 Pub. # 150200054300A...
  • Page 4 Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC.
  • Page 5 All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
  • Page 6 RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS. * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.

  • Page 7: Japan Vcci Class A

    OMPLIANCES FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 8 OMPLIANCES CE Mark Declaration of Conformance for EMI and Safety (EEC) SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2 08970 - Sant Joan Despí, Barcelona, Spain. This information technology equipment complies with the requirements of the Council...
  • Page 9 OMPLIANCES Australia AS/NZS 3548 (1995) - Class A N11846 SMC contact for products in Australia is: SMC Communications Pty. Ltd. Suite 18, 12 Tryon Road, Lindfield NSW2070, Phone: 61-2-94160437 Fax: 61-2-94160474 Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic port, never look at the transmit laser while CLASS I it is powered on.
  • Page 10 OMPLIANCES • This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions. France and Peru only This unit cannot be powered from IT †...
  • Page 11 OMPLIANCES Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch: AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié. • Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à...
  • Page 12 OMPLIANCES Cordon électrique - Il doit être agréé dans le pays d’utilisation Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011. Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”) LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type HO3VVF3GO.75 (minimum).

  • Page 13: Warnings And Cautionary Messages

    OMPLIANCES Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

  • Page 14: End Of Product Life Span

    The following publication gives specific information on how to operate and use the management functions of the switches: SMC8824M, SMC8848M Management Guide Also, as part of both switches firmware, there is an online web-based help that describes all management related features.

  • Page 15: Table Of Contents

    ABLE OF ONTENTS About the TigerStack II 10/100/1000 ... . . 1-1 Overview ..........1-1 Switch Architecture .
  • Page 16 ABLE OF ONTENTS Mounting ..........3-4 Rack Mounting .
  • Page 17 ABLE OF ONTENTS PPENDICES Troubleshooting ......A-1 Diagnosing Switch Indicators ....... . . A-1 Diagnosing Power Problems with the LEDs .
  • Page 18 ABLE OF ONTENTS Glossary Index...
  • Page 19 ABLES Table 1-1 Port Status LEDs ........1-5 Table 1-2 System Status LEDs .
  • Page 20 IGURES Figure 1-1 Front Panels ........1-2 Figure 1-2 Rear Panel .

  • Page 21: About The Tigerstack Ii 10/100/1000

    II 10/100/1000 IGER TACK Overview SMC’s TigerStack II 10/100/1000 SMC8824M and SMC8848M are intelligent multilayer switches (Layer 2, 3) with 24/48 10/100/ 1000BASE-T ports, four of which are combination ports that are shared with four SFP transceiver slots (see Figure 1-1, Ports 21-24/45-48). The rear panel provides two slots for single-port 10 Gigabit Ethernet hot-swappable expansion modules, and two stacking ports.

  • Page 22: Switch Architecture

    IP traffic to release valuable resources for non-IP routing or WAN access. With wire-speed performance, these switches can significantly improve the throughput between IP segments or VLANs. Stack ID Console Port Port Status LEDs SMC8848M Stack Master TigerStack II 10/100/1000 Module Diag...

  • Page 23: Network Management Options

    ESCRIPTION OF ARDWARE These switches include built-in stacking ports that enable up to eight units to be connected together through a 48 Gbps stack backplane. The switch stack can be managed from a master unit using a single IP address. These switches also include two slots on the rear panel for slide-in single-port 10GBASE modules with XFP transceivers.

  • Page 24: Sfp Slots

    The Small Form Factor Pluggable (SFP) transceiver slots are shared with four of the RJ-45 ports (ports 21-24 for the SMC8824M and ports 45-48 for the SMC8848M). In its default configuration, if an SFP transceiver (purchased separately) is installed in a slot and has a valid link on its port, the associated RJ-45 port is disabled and cannot be used.

  • Page 25: Port And System Status Leds

    ESCRIPTION OF ARDWARE Port and System Status LEDs switches include a display panel for key system and port indications These that simplify installation and network troubleshooting. The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following tables.

  • Page 26: Table 1-2 System Status Leds

    II 10/100/1000 BOUT THE IGER TACK System Status LEDs Stack Master TigerStack II 10/100/1000 8848M Module Diag Master Stack ID Console Select Stack Link Figure 1-4 System LEDs Table 1-2 System Status LEDs Condition Status Power Green Internal power is operating normally. Amber Internal power supply fault.
  • Page 27 ESCRIPTION OF ARDWARE Table 1-2 System Status LEDs (Continued) Condition Status Stack Green Switch is the Master unit of the stack. State Master may include topology discovery, IP assignment, or normal operations. Flashing Green Switch is the Master unit of the stack, system is initializing.

  • Page 28: Optional Redundant Power Supply

    IGER TACK Optional Redundant Power Supply SMC supports an optional Redundant Power Supply (RPS), that can supply power to the switch in the event the internal power supply fails. Power Supply Sockets There are two power sockets on the rear panel of each switch. The standard power socket is for the AC power cord.

  • Page 29: Features And Benefits

    EATURES AND ENEFITS Extender Module LEDs The optional 10GBASE slide-in module includes its own integrated LED indicators on the module’s front panel. The following table describes the LEDs. Table 1-3 Module LEDs Condition Status Link/ On/Flashing Port has a valid link at 10 Gbps. Flashing indicates Activity Green activity.

  • Page 30: Expandability

    Transparent bridging. • Aggregate duplex bandwidth of up to 128 Gbps for the SMC8824M or 176 Gbps for the SMC8848M. • Switching table with a total of 8K MAC address entries and 2K IPv4 address entries or 1K IPv6 address entries.

  • Page 31: Network Planning

    HAPTER ETWORK LANNING Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. These switches have, therefore, been recognized as one of the most important building blocks for today’s networking technology.

  • Page 32: Application Examples

    ETWORK LANNING Application Examples The TigerStack II 10/100/1000 is not only designed to segment your network, but also to provide a wide range of options in setting up network connections and linking VLANs or IP subnets. Some typical applications are described below. Collapsed Backbone The TigerStack II 10/100/1000 is an excellent choice for mixed Ethernet, Fast Ethernet, and Gigabit Ethernet installations where significant growth...

  • Page 33: Network Aggregation Plan

    PPLICATION XAMPLES Network Aggregation Plan With 24 or 48 parallel bridging ports (i.e., 24 or 48 distinct collision domains), a Gigabit switch stack can collapse a complex network down into a single efficient bridged node, increasing overall bandwidth and throughput. In the figure below, the 10/100/1000BASE-T ports in a stack of 48-port Gigabit Ethernet switches are providing 1000 Mbps connectivity through stackable switches.

  • Page 34: Remote Connections With Fiber Cable

    ETWORK LANNING Remote Connections with Fiber Cable Fiber optic technology allows for longer cabling than any other media type. A 1000BASE-SX (MMF) link can connect to a site up to 550 meters away, a 1000BASE-LX (SMF) link up to 5 km, and a 1000BASE-ZX link up to 100 km.

  • Page 35: Making Vlan Connections

    PPLICATION XAMPLES Making VLAN Connections These switches support VLANs which can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secure and cleaner network environment.

  • Page 36: Application Notes

    ETWORK LANNING Application Notes 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2.

  • Page 37: Installing The Switch

    HAPTER NSTALLING THE WITCH Selecting a Site TigerStack II 10/100/1000 units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. • The site should: - be at the center of all the devices you want to link and near a power outlet.

  • Page 38: Ethernet Cabling

    NSTALLING THE WITCH Ethernet Cabling To ensure proper operation when installing the switches into a network, make sure that the current cables are suitable for 10BASE-T, 100BASE-TX or 1000BASE-T operation. Check the following criteria against the current installation of your network: •...

  • Page 39: Equipment Checklist

    • Console cable (RJ-45 to RS-232) • This Installation Guide • Installation and Management Guide CD • SMC Warranty Registration Card—be sure to complete and return to Optional Rack-Mounting Equipment If you plan to rack-mount the switches, be sure to have the following equipment available: •...

  • Page 40: Mounting

    NSTALLING THE WITCH Mounting A TigerStack II 10/100/1000 unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Rack Mounting Before rack mounting the switch, pay particular attention to the following factors: •...

  • Page 41: Figure 3-2 Attaching The Brackets

    OUNTING To rack-mount devices: 1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit. S ta c k M a s te r P w r M a s te r S e le R P S S ta c k ID...

  • Page 42: Desktop Or Shelf Mounting

    NSTALLING THE WITCH 3. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, mount them in the rack, one below the other, in any order. 5.

  • Page 43: Installing An Optional Module Into The Switch

    NSTALLING AN PTIONAL ODULE INTO THE WITCH Installing an Optional Module into the Switch Figure 3-5 Installing an Optional Module Note: The slide-in modules are hot-swappable, you do not need to power off the switch before installing or removing a module. To install an optional module into the switch, do the following: 1.

  • Page 44: Installing An Optional Sfp Or Xfp Transceiver Into The Switch

    NSTALLING THE WITCH 6. The Module LED on the switch’s front panel should turn green to confirm that the module is correctly installed and ready to use. Installing an Optional SFP or XFP Transceiver into the Switch S ta c k M a s te r P w r...

  • Page 45: Connecting Switches In A Stack

    ONNECTING WITCHES IN A TACK 3. Slide the transceiver into the slot until it clicks into place. Note: SFP and XFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

  • Page 46: Figure 3-7 Making Stacking Connections

    NSTALLING THE WITCH 4. (Optional) To form a wrap-around topology, plug one end of a stack cable into the Down port on the bottom unit and the other end into the Up port on the top unit. Figure 3-7 Making Stacking Connections 5.

  • Page 47: Stacking Topologies

    ONNECTING WITCHES IN A TACK Stacking Topologies All units in the stack must be connected via stacking cable. You can connect units in a simple cascade configuration, connecting Down ports to Up ports, from the top unit to the bottom unit. Using this “line” topology, if any link or unit in the stack fails, the stack is split and two separate segments are formed.

  • Page 48: Connecting To A Power Source

    NSTALLING THE WITCH Connecting to a Power Source To connect a device to a power source: 1. Insert the power cable plug directly into the socket located at the back of the device. Figure 3-8 Power Socket 2. Plug the other end of the cable into a grounded, 3-pin, AC power source.

  • Page 49: Connecting To The Console Port

    ONNECTING TO THE ONSOLE Connecting to the Console Port The RJ-45 serial port on the switch’s front panel is used to connect to the switch for out-of-band console configuration. The on-board configuration program can be accessed from a terminal or a PC running a terminal emulation program.
  • Page 50 NSTALLING THE WITCH 3-14...

  • Page 51: Making Network Connections

    HAPTER AKING ETWORK ONNECTIONS Connecting Network Devices The TigerStack II 10/100/1000 units are designed to interconnect multiple segments (or collision domains). It can be connected to network cards in PCs and servers, as well as to hubs, switches or routers. It may also be connected to devices using optional XFP or SFP transceivers.

  • Page 52: Connecting To Pcs, Servers, Hubs And Switches

    AKING ETWORK ONNECTIONS Connecting to PCs, Servers, Hubs and Switches 1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector. Figure 4-1 Making Twisted-Pair Connections 2. If the device is a PC card and the switch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet.

  • Page 53: Network Wiring Connections

    WISTED EVICES Network Wiring Connections Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follows.

  • Page 54: Fiber Optic Sfp Devices

    AKING ETWORK ONNECTIONS Fiber Optic SFP Devices An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-ZX) can be used for a backbone connection between switches, or for connecting to a high-speed server. Each single-mode fiber port requires 9/125 micron single-mode fiber optic cable with an LC connector at both ends.

  • Page 55: 10 Gbps Fiber Optic Connections

    10 G IBER PTIC ONNECTIONS 3. Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC connectors are keyed, the cable can be attached in only one orientation. S t a c k M a s t e r...
  • Page 56 AKING ETWORK ONNECTIONS Warning: These switches use lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

  • Page 57: Figure 4-4 Connecting To An Xfp Transceiver

    10 G IBER PTIC ONNECTIONS Figure 4-4 Connecting to an XFP Transceiver 4. As a connection is made, check the Link LED on the module to be sure that the connection is valid. The 10G fiber optic ports operate at 10 Gbps full duplex. The maximum length for fiber optic cable operating at 10 Gbps will depend on the fiber type as listed under “10 Gbps Ethernet Collision Domain”...

  • Page 58: Connectivity Rules

    AKING ETWORK ONNECTIONS Connectivity Rules When adding hubs (repeaters) to your network, please follow the connectivity rules listed in the manuals for these products. However, note that because switches break up the path for connected devices into separate collision domains, you should not include the switch or connected cabling in your calculations for cascade length involving other devices.

  • Page 59: 1000 Mbps Gigabit Ethernet Collision Domain

    ONNECTIVITY ULES Table 4-2 Maximum 10GBASE-LR 10 Gigabit Ethernet Cable Length Fiber Size Fiber Maximum Cable Connector Bandwidth Length 9/125 micron 10 km (6.2 miles) single-mode fiber Table 4-3 Maximum 10GBASE-ER 10 Gigabit Ethernet Cable Length Fiber Size Fiber Maximum Cable Connector Bandwidth Length...

  • Page 60: 100 Mbps Fast Ethernet Collision Domain

    AKING ETWORK ONNECTIONS Table 4-7 Maximum 1000BASE-ZX Fiber Optic Cable Length Fiber Diameter Fiber Cable Length Connector Bandwidth Range 9/125 micron 70* - 100 km single-mode fiber (43.5 - 62.1 miles) * For link spans exceeding 70 km, you may need to use premium single mode fiber or dispersion shifted single mode fiber 100 Mbps Fast Ethernet Collision Domain Table 4-8 Maximum Fast Ethernet Cable Length...

  • Page 61: Cable Labeling And Connection Records

    ABLE ABELING AND ONNECTION ECORDS Cable Labeling and Connection Records When planning a network installation, it is essential to label the opposing ends of cables and to record where each cable is connected. Doing so will enable you to easily locate inter-connected devices, isolate faults and change your topology without need for unnecessary time consumption.
  • Page 62 AKING ETWORK ONNECTIONS 4-12...

  • Page 63: Troubleshooting

    Check connections between the switch, the power cord, and the wall outlet. • Contact your dealer for assistance. • Contact SMC Technical Support. Power LED is Amber • Internal power supply has failed. Contact your local dealer for assistance. Diag LED is Amber •...

  • Page 64: Diagnosing Power Problems With The Leds

    ROUBLESHOOTING Table A-1 Troubleshooting Chart (Continued) Symptom Action Stack Link LED is • The uplink/downlink has failed. Flashing Green/Amber • For the indicated stack link, check that the stacking cables are properly connected. Replace the stacking cable if necessary. • Power cycle the switch to try and clear the condition.

  • Page 65: Power And Cooling Problems

    OWER AND OOLING ROBLEMS Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fans on the unit are unobstructed and running prior to shutdown.

  • Page 66: Stack Troubleshooting

    ROUBLESHOOTING Stack Troubleshooting If a stack fails to initialize or function, first check the following items: • Check that all stacking cables are properly connected. • Check if any stacking cables appear damaged. • Check that only one Stack Master button is pressed in. •...

  • Page 67: Cables

    PPENDIX ABLES Twisted-Pair Cable and Pin Assignments For 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes.

  • Page 68: Table B-1 10/100Base-Tx Mdi And Mdi-X Port Pinouts

    ABLES 10BASE-T/100BASE-TX Pin Assignments Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3 or better cable for 10 Mbps connections, or 100-ohm Category 5 or better cable for 100 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

  • Page 69: Twisted-Pair Cable And Pin Assignments

    WISTED ABLE AND SSIGNMENTS Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. (When auto-negotiation is enabled for any RJ-45 port on these switches, you can use either straight-through or crossover cable to connect to any device type.) You must connect all four wire pairs as shown in the following diagram to...

  • Page 70: Crossover Wiring

    ABLES Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (indicating MDI-X) or neither port is labeled with an “X” (which indicates MDI), a crossover must be implemented in the wiring.

  • Page 71: 1000Base-T Pin Assignments

    WISTED ABLE AND SSIGNMENTS 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. The table below shows the 1000BASE-T MDI and MDI-X port pinouts. These ports require that all four pairs of wires be connected.

  • Page 72: Adjusting Existing Category 5 Cabling To Run 1000Base-T

    ABLES Note that when testing your cable installation, be sure to include all patch cables between switches and end devices. Adjusting Existing Category 5 Cabling to Run 1000BASE-T If your existing Category 5 installation does not meet one of the test parameters for 1000BASE-T, there are basically three measures that can be applied to try and correct the problem: 1.

  • Page 73: Specifications

    1000BASE-T: RJ-45 (100-ohm, UTP or STP cable; Category 5, 5e, or 6) *Maximum Cable Length - 100 m (328 ft) Buffer Architecture SMC8824M: 0.75 Mbytes SMC8848M: 1.5 Mbytes (two switch ASICs – 0.75 Mbytes each) Aggregate Bandwidth SMC8824M: 128 Gbps SMC8848M: 176 Gbps...
  • Page 74 RPS (Redundant Power Supply) Port: Status (link, speed, activity) Weight SMC8824M: 3.72 kg (8.44 lbs) SMC8848M: 4.34 kg (9.59 lbs) Size 44.0 x 41.5 x 4.4 cm (17.3 x 16.3 x 1.7 in.) Temperature Operating: 0 to 50 °C (32 to 122 °F) Storage: -40 to 70 °C (-40 to 158 °F)

  • Page 75: Switch Features

    0.72 A @ 110 VAC (with two expansion modules) 0.36 A @ 240 VAC (without expansion modules) 0.37 A @ 240 VAC (with two expansion modules) SMC8848M: 0.97 A @ 110 VAC (without expansion modules) 1.16 A @ 110 VAC (with two expansion modules) 0.47 A @ 240 VAC (without expansion modules)

  • Page 76: Standards

    PECIFICATIONS Standards IEEE 802.3-2002 Ethernet, Fast Ethernet, Gigabit Ethernet IEEE 802.3ae 10 Gigabit Ethernet IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE D802.1Q Virtual LAN ISO/IEC 8802-3 Compliances CE Mark Emissions FCC Class A Industry Canada Class A...

  • Page 77: Extender Modules

    XTENDER ODULES Extender Modules 10G Extender Module (XFP) Ports 1 slot for 10GBASE XFP transceiver Communication Speed 10 Gbps Communication Mode Full duplex Network Interface XFP slot Standards IEEE 802.3ae 10 Gigabit Ethernet Warranty Limited Lifetime...
  • Page 78 PECIFICATIONS...

  • Page 79: German Instructions

    PPENDIX ERMAN NSTRUCTIONS Eine Site Auswählen (Selecting a Site - German) Die Schalter können in ein Standard-19-Zoll-Ausrüstungsgestell oder auf eine flache Ebene montiert werden. Zum Auswählen eines Standortes beachten Sie bitte die nachstehenden Richtlinien. • Die Site sollte: Sich in der Mitte aller anzuschließenden Geräte sowie in der Nähe einer Netzsteckdose befinden;...

  • Page 80: Montage (Rack Mounting Instructions - German

    ONTAGE OUNTING NSTRUCTIONS ERMAN moglichen elektrischen Storungen verlegt wird, wie z. B. von Radios und Transmittern. • Sicherstellen, dass das Gerat an eine separate Stromquelle mit Erdanschlus mit einer Netzspannung von 100 bis 240 V AC (Wechselstromspannung), 50 bis 60 Hz, und innerhalb in einem Abstand von 2,44 m (8 Fus) zu jedem Gerat installiert wird und on einem separaten Trennschalter bzw.
  • Page 81 ERMAN NSTRUCTIONS So montieren Sie Geräte an ein Rack: 1. Befestigen Sie die Metallwinkel mit den im Metallwinkel-Montageset erhältlichen Schrauben an dem Gerät. 2. Befestigen Sie das Gerät mit vier Rackmontageschrauben (nicht beigelegt) an dem Rack. 3. Wenn Sie nur einen Switch installieren, dann springen Sie bitte über zu "Verbinden mit einer Stromquelle"...
  • Page 82 ONTAGE OUNTING NSTRUCTIONS ERMAN...

  • Page 83: Table E-1 Tigerstack Ii 10/100/1000 Products And Accessories

    1 stacking cable for inter-switch connection (30 cm) SMC8700S-130 1 stacking cable for inter-switch connection (1.3 m) Redundant power unit with cables, supports one SMCRPU14 device * Also available in models for Continental Europe and the UK. Note: For 10GBASE-ER, SMC recommends Finisar transceiver, part number FTRX-1611-3.

  • Page 84: Ordering Information

    RDERING NFORMATION...
  • Page 85 LOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. 1000BASE-LX IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125, 62.5/125 or 9/125 micron core fiber cable.
  • Page 86 LOSSARY 10GBASE-LR IEEE 802.3ae specification for 10 Gigabit Ethernet over two strands of 9/125 micron core single-mode fiber cable. 10GBASE-SR IEEE 802.3ae specification for 10 Gigabit Ethernet over two strands of 50/125 micron core multimode fiber cable. 10 Gigabit Ethernet A 10 Gbps network communication system based on Ethernet.

  • Page 87: Full Duplex

    LOSSARY End Station A workstation, server, or other device that does not forward traffic. Ethernet A network communication system developed and standardized by DEC, Intel, and Xerox, using baseband transmission, CSMA/CD access, logical bus topology, and coaxial cable. The successor IEEE 802.3 standard provides for integration into the OSI model and extends the physical layer and media with repeaters and implementations that operate on fiber, thin coax and twisted-pair cable.
  • Page 88 LOSSARY IEEE 802.3ae Defines the physical layer specifications for 10 Gigabit Ethernet. IEEE 802.3u Defines CSMA/CD access method and physical layer specifications for 100BASE-TX Fast Ethernet. (Now incorporated in IEEE 802.3-2002.) IEEE 802.3x Defines Ethernet frame start and stop requests and timers used for flow control on full-duplex links.

  • Page 89: Network Diameter

    LOSSARY Management Information Base (MIB) An acronym for Management Information Base. It is a set of database objects that contains information about the device. Media Access Control (MAC) A portion of the networking protocol that governs access to the transmission medium, facilitating the exchange of data between network nodes.
  • Page 90 LOSSARY Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol. Unshielded twisted-pair cable. Virtual LAN (VLAN) A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network.
  • Page 91 NDEX Numerics 10 Gbps connectivity rules 4-8 cable 10 Mbps connectivity rules 4-10 Ethernet cable compatibility 3-2 100 Mbps connectivity rules 4-10 labeling and connection records 4-11 1000 Mbps connectivity rules 4-9 lengths 4-10 1000BASE-LX fiber cable lengths 4-9 cleaning fiber terminators 4-4 1000BASE-SX fiber cable lengths 4-9 compliances 1000BASE-T...
  • Page 92 NDEX grounding for racks 3-4 management agent 1-3 features 1-10 out-of-band 1-3 SNMP 1-3 IEEE 802.3 Ethernet 1-9 web-based 1-3 IEEE 802.3ae 10 Gigabit Ethernet 1-9 modules, 10G 1-8 IEEE 802.3u Fast Ethernet 1-9 modules, 10GBASE-LR C-5 IEEE 802.3z Gigabit Ethernet 1-9 mounting the switch indicators, LED 1-5 in a rack 3-4...
  • Page 93 NDEX standards compliance C-4 rack mounting 3-4 IEEE C-4 redundant power unit 1-8 status LEDs 1-5 RJ-45 port 1-3 surge suppressor, using 3-1 connections 4-1 switch architecture 1-2 pinouts B-5 switching, introduction to 2-1 connecting 3-12 installing in a rack 3-6 installing on a desktop 3-6 temperature within a rack 3-4 RPU, optional redundant power unit 1-8...
  • Page 94 NDEX Index-4...
  • Page 96 81-45-224-2332; Fax 81-45-224-2331 Australia: 61-2-8875-7887; Fax 61-2-8875-7777 India: 91-22-8204437; Fax 91-22-8204443 If you are looking for further contact information, please visit www.smc.com, www.smc-europe.com, or www.smc-asia.com. 38 Tesla Model Numbers: SMC8824M, SMC8848M Irvine, CA 92618 Pub. Number: 150200054300A E022006-R01 Phone: (949) 679-8000...

This manual is also suitable for:

Tigerstack ii smc8824m8824m8848m

Table of Contents