Honeywell Genesis XP 7680g User Manual

Honeywell Genesis XP 7680g User Manual

Presentation area imager
Table of Contents

Advertisement

Quick Links

Genesis™ XP 7680g
Presentation Area Imager
User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Genesis XP 7680g and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Honeywell Genesis XP 7680g

  • Page 1 Genesis™ XP 7680g Presentation Area Imager User Guide...
  • Page 2: Licenses Of Third-Party Software

    Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in this publication.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS Customer Support ........................xiii Technical Assistance ......................xiii Product Service and Repair ....................xiii Limited Warranty ........................xiii Chapter 1 - Get Started ..................1 About This Manual......................... 1 Unpack Your Device........................1 Scanner Features ........................... 2 Connect the Device........................
  • Page 4 CTS/RTS Emulation ......................13 ACK/NAK Mode........................13 ® Verifone Ruby Terminal......................13 ® Gilbarco Terminal........................14 Honeywell Bioptic Aux Port .....................14 ® Datalogic™ Magellan Aux Port....................14 Wincor Nixdorf Terminal ......................15 Wincor Nixdorf Beetle™ Terminal ..................15 Wincor Nixdorf RS232 Mode A....................16 Keyboard Country Layout......................16 Keyboard Wedge Modifiers......................23 ALT Mode ..........................23...
  • Page 5 Scanner-Bioptic Packet Mode..................32 Scanner-Bioptic ACK/NAK Mode..................33 Scanner-Bioptic ACK/NAK Timeout ................33 Chapter 3 - Input/Output Settings .............35 Power Up Beeper ..........................35 Beep on BEL Character ......................35 Trigger Click............................36 Good Read and Error Indicators.....................36 Beeper – Good Read ......................36 Beeper Volume – Good Read ....................36 Beeper Pitch –...
  • Page 6 Hands Free Time-Out.........................47 Reread Delay..........................47 User-Specified Reread Delay....................48 2D Reread Delay ........................48 Character Activation ........................48 Activation Character ......................49 End Character Activation After Good Read..............49 Character Activation Timeout ..................50 Character Deactivation......................50 Deactivation Character .......................50 Illumination Lights........................51 Aimer Delay ............................51 User-Specified Aimer Delay ....................52 Aimer Mode ............................52 Presentation Aimer Mode......................53 Enhanced Object Detection ....................53...
  • Page 7 Video Reverse..........................69 Working Orientation........................70 Optimized Scanning for Tobacco Products...............71 Chapter 4 - Data Edit ..................73 Prefix/Suffix Overview .......................73 Points to Keep In Mind ......................73 Add a Prefix or Suffix: ......................74 Example: Add a Tab Suffix to All Symbologies ............74 Clear One or All Prefixes or Suffixes................74 Add a Carriage Return Suffix to All Symbologies............75 Prefix Selections ...........................75 Suffix Selections...........................75...
  • Page 8 Primary/Alternate Data Formats ...................97 Single Scan Data Format Change ..................97 Chapter 6 - Symbologies................99 All Symbologies ......................... 100 Message Length Description....................100 Codabar ............................100 Code 39............................103 Interleaved 2 of 5 ........................106 NEC 2 of 5............................ 108 Code 93............................
  • Page 9 Codablock A..........................139 Codablock F..........................140 Label Code ...........................141 PDF417 ............................141 MacroPDF417 ..........................142 MicroPDF417 ..........................142 GS1 Composite Codes ......................143 GS1 Emulation ...........................144 TCIF Linked Code 39 (TLC39)....................145 QR Code ............................146 DotCode ............................148 Digimarc Barcode™ ........................149 Data Matrix ..........................151 MaxiCode............................152 Aztec Code ...........................153 Chinese Sensible (Han Xin) Code..................154 Postal Codes - 2D........................155 Planet Code Check Digit....................159...
  • Page 10 Intelligent Signature Capture - IMGBOX ................ 176 Signature Capture Optimize ..................176 IMGBOX Modifiers......................177 Chapter 8 - Utilities..................183 To Add a Test Code I.D. Prefix to All Symbologies ............183 Show Software Revision ......................183 Test Menu ............................ 183 TotalFreedom..........................
  • Page 11 Chapter 11 - Maintenance and Troubleshooting ........223 Repairs............................223 Maintenance ..........................223 Clean the Scanner ......................223 About Disinfectant-ready Models................224 Inspect Cords and Connectors..................224 Replace Cable..........................224 Replace an Interface Cable.....................224 Troubleshoot ..........................225 Chapter A - Reference Charts ..............227 Symbology Charts........................227 Linear Symbologies ......................227 2D Symbologies ........................228 Postal Symbologies ......................229 ASCII Conversion Chart (Code Page 1252) ..............230...
  • Page 12 Genesis XP User Guide...
  • Page 13: Customer Support

    Support to search our knowledge base for a solution or to log into the Technical Support portal. Product Service and Repair Honeywell International Inc. provides service for all of its products through service centers throughout the world. Go to sps.honeywell.com...
  • Page 14 Genesis XP User Guide...
  • Page 15: Chapter 1 - Get Started

    About This Manual This User Guide provides installation and programming instructions for the Genesis XP 7680g hands-free area imaging scanner. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell barcode scanners are factory programmed for the most common terminal and communications settings.
  • Page 16: Scanner Features

    Scanner Features Scan Trigger Illumination LEDs Illumination LEDs IR Wakeup Scanner Sensor Status LED Ring Accessory Expansion Port Cable Port Genesis 7680g User Guide...
  • Page 17: Connect The Device

    Connect the Device Note: It is important to insert the black O-ring onto the end of the communication cable as shown, and make sure that the O-ring cannot be seen after the cable is inserted into the scanner. This ensures proper assembly and IP52 compliance function. IP52 Connect with USB A scanner can be connected to the USB port of a computer.
  • Page 18: Connect With Keyboard Wedge

    Connect with Keyboard Wedge A scanner can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection: 1.
  • Page 19: Connect With Rs232 Serial Port

    Connect with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer. Genesis XP 7680 Scanner RS232 Serial Port Connection: Note: The power supply must be ordered separately, if needed.
  • Page 20: Connect With Rs485

    Connect with RS485 A Xenon scanner can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. Genesis XP 7680 Scanner RS485 Connection: Note: The power supply must be ordered separately, if needed. 2.
  • Page 21: Troubleshooting

    Error Menu Barcode Security Settings Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest...
  • Page 22: Reset The Custom Defaults

    then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults barcode. Set Custom Defaults Save Custom Defaults You may have a series of custom settings and want to correct a single setting.
  • Page 23: Chapter 2 - Program The Interface

    CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play barcodes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
  • Page 24: Laptop Direct Connect

    Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect barcode allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect barcode also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 25).
  • Page 25: Usb Ibm Surepos

    IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each barcode above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
  • Page 26: Usb Pc Or Macintosh Keyboard

    No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
  • Page 27: Cts/Rts Emulation

    CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off ® Verifone Ruby Terminal Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This barcode sets the baud rate to 1200 bps and the data format to 8 data bits, mark parity bit, 1 stop bit.
  • Page 28: Gilbarco ® Terminal

    Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This barcode sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
  • Page 29: Wincor Nixdorf Terminal

    Wincor Nixdorf Terminal Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Wincor Nixdorf Beetle™...
  • Page 30: Wincor Nixdorf Rs232 Mode A

    Wincor Nixdorf RS232 Mode A Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology: Symbology Prefix...
  • Page 31 Keyboard Countries (Continued) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Genesis XP User Guide...
  • Page 32 Keyboard Countries (Continued) Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Genesis XP User Guide...
  • Page 33 Keyboard Countries (Continued) Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Genesis XP User Guide...
  • Page 34 Keyboard Countries (Continued) Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Genesis XP User Guide...
  • Page 35 Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Genesis XP User Guide...
  • Page 36 Keyboard Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Genesis XP User Guide...
  • Page 37: Keyboard Wedge Modifiers

    Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United States (Dvorak right) United States (International) Uzbek (Cyrillic) Keyboard Wedge Modifiers ALT Mode If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode.
  • Page 38: Keyboard Style

    If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off. * Off 3 Characters 4 Characters Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock.
  • Page 39: Keyboard Conversion

    Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off. This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
  • Page 40: Control Character Output

    Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D.
  • Page 41 Default = Control + X Mode Off. Windows Mode Control + X Mode On * Control + X Mode Off DOS Mode Control + X Mode On Windows Mode Prefix/Suffix DOS Mode Control + X Mode On with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode Turbo Mode: The scanner sends characters to a terminal faster.
  • Page 42: Rs232 Modifiers

    Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off. Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate.
  • Page 43: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    19200 38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
  • Page 44: Rs232 Receiver Time-Out

    7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out.
  • Page 45: Rs232 Timeout

    Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 31) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume.
  • Page 46: Ack/Nak

    * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
  • Page 47: Scanner-Bioptic Ack/Nak Mode

    Scanner-Bioptic ACK/NAK Mode Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default = Bioptic ACK/NAK Off.
  • Page 48 Genesis XP User Guide...
  • Page 49: Chapter 3 - Input/Output Settings

    CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off barcode(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off - Scanner * Power Up Beeper On - Scanner...
  • Page 50: Trigger Click

    Trigger Click To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On barcode below. Scan the Trigger Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger Click Off.
  • Page 51: Beeper Pitch - Good Read

    * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2700 Hz) High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error.
  • Page 52: Beeper Duration - Good Read

    Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
  • Page 53: Good Read Delay

    to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 241, then Save. Default = 1. Number of Error Beeps/LED Flashes Good Read Delay This sets the minimum amount of time before the scanner can read another barcode.
  • Page 54: Object Detection Mode

    Object Detection Mode Object Detection Mode uses an infrared (IR) beam to detect when an object is in the scanner’s field of view. When an object is detected, the scanner attempts to scan the barcode. Scan Object Detection Mode then the Short Range code for a target that’s approximately 6 inches (15cm) away.
  • Page 55: Trigger Timing

    scanner’s action will be. For example, you could double-press the trigger to go into imaging mode, then the next trigger press takes the image. The scanner then reverts to scanning mode. Use the following codes to configure what action you would like the scanner to take when in Trigger Toggle mode.
  • Page 56: Serial Trigger

    Trigger Toggle Timeout This sets the length of time the scanner stays in trigger toggle mode before reverting to scan mode. After scanning the Trigger Toggle Timeout barcode, set the time-out duration (from 0 to 65 seconds) by scanning digits from the Programming Chart, beginning on page 241, then Save.
  • Page 57: Triggered Presentation Mode

    Scan the following barcode to program your scanner for Presentation Mode. Presentation Mode Triggered Presentation Mode This mode uses light to detect the presence of an object. Default = Ambient and Scanner Light. Ambient Light Only *Ambient and Scanner Light Presentation LED Behavior after Decode When a scanner is in presentation mode, the LED aimer dims 30 seconds after a barcode is decoded.
  • Page 58 window you specify using the Top of Presentation Centering Window, Bottom of Presentation Centering Window, Left, and Right of Presentation Centering Window barcodes. In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read.
  • Page 59: Poor Quality Codes

    Top of Presentation Centering Window Bottom of Presentation Centering Window Left of Presentation Centering Window Right of Presentation Centering Window Poor Quality Codes Poor Quality 1D Codes This setting improves the scanner’s ability to read damaged or badly printed linear barcodes.
  • Page 60: Poor Quality Pdf Codes

    Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a complete barcode cannot be seen in one image. This setting does not affect 1D barcode reading.
  • Page 61: Hands Free Time-Out

    CodeGate On Out-of-Stand Hands Free Time-Out Presentation Mode is referred to as a “hands free” mode. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out.
  • Page 62: User-Specified Reread Delay

    User-Specified Reread Delay If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 241, then Save. User-Specified Reread Delay 2D Reread Delay Sometimes 2D barcodes can take longer to read than other barcodes.
  • Page 63: Activation Character

    barcode is transmitted. Scan the On barcode to use character activation, then use Activation Character (page 49) to select the character you will send from the host to start scanning. Default = Off. * Off Activation Character This sets the character used to trigger scanning when using Character Activation Mode.
  • Page 64: Character Activation Timeout

    Character Activation Timeout You can set a timeout for the length of time the illumination remains on and attempting to decode barcodes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 241, then Save.
  • Page 65: Illumination Lights

    Illumination Lights If you want the illumination lights on while reading a barcode, scan the Lights On barcode, below. However, if you want to turn just the lights off, scan the Lights Off barcode. Default = Lights On. Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 52).
  • Page 66: User-Specified Aimer Delay

    User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 241, then Save. Delay Duration Aimer Mode This feature allows you to turn the aimer on and off.
  • Page 67: Presentation Aimer Mode

    Presentation Aimer Mode This feature allows you to turn the aimer on and off while the scanner is in Presentation Mode, Presentation - Mobile Phone, Streaming Presentation Mode, or Streaming Presentation - Mobile Phone. When the Interlaced bar code is scanned, the aimer is interlaced with the illumination LEDs.
  • Page 68: Centering

    Centering Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read.
  • Page 69 Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.
  • Page 70: Preferred Symbology

    Bottom of Centering Window Left of Centering Window Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both barcode symbologies appear on the same label, but the lower priority symbology cannot be disabled. For example, you may be using the scanner in a retail setting to read U.P.C.
  • Page 71: High Priority Symbology

    High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology barcode below. On the Symbology Charts on page 227, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 241, then Save.
  • Page 72: Output Sequence Overview

    Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the barcodes are scanned. You can define up to 15 barcodes in an output sequence.
  • Page 73: Output Sequence Editor Commands

    5. End Output Sequence Editor Use FF to terminate this string or to begin another output sequence. If you are using barcodes, scan F F. Scan Save to save your entries. Other Programming Selections If you are creating an output sequence using barcodes, scan Discard (page 242) to exit without saving any output sequence changes.
  • Page 74 Output Sequence Example 1 - Three Symbologies In this example, you are scanning PDF417, Code 128, and Code 39 barcodes, but you want the scanner to output Code 39 first, Code 128 second, and PDF417 third. Set up the sequence editor with the following command line: SEQBLK sequence editor start command code identifier for Code 39...
  • Page 75 The data is output as: CODE39SMPLTSTMSGCODE128MSGPDF417 Output Sequence Example 2 - Three Symbologies with <> Separators In this example, you are scanning the same three barcodes, but you want <> brackets and a carriage return and line feed to separate your output. The sequence editor would use the same command line as shown in Output Sequence Example 1 - Three Symbologies...
  • Page 76: Enter Output Sequence

    And add the carriage return and line feed as a suffix: SEQSUF99 separator for suffixes, 99 = all symbologies carriage return line feed The whole command line would look like this: SEQBLK62999943FF6A999954FF7299994DFF;SEQSEP993C3E;SEQSUF990D SEQDFT;SEQ_EN1;SEQBLK62999943FF6A999954FF7299994DFF;SEQSEP993C3E;SEQSUF990D0A. The data is output as: CODE39SMPL<>TSTMSGCODE128<>MSGPDF417 [CR] [LF] Enter Output Sequence If you are using barcodes to create your output sequence, scan Enter Output Sequence to begin scanning your string.
  • Page 77 You would use the same command line as shown in Output Sequence Example 2 - Three Symbologies with <> Separators (page 61): SEQBLK sequence editor start command code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 43h = "C"...
  • Page 78 SEQTTS1 transmit partial sequence SEQIPR99 add partial sequence prefix, 99 = all symbologies right bracket (>) left bracket (<) The whole command line would look like this: SEQBLK62999943FF6A999954FF7299994DFF;SEQISE993C3E;SEQISU990D0 A;SEQTTS1;SEQIPR993E5041525449414C3C. SEQDFT;SEQ_EN1;SEQBLK62999943FF6A999954FF7299994DFF;SEQISE993C3E;SEQISU990D0A; SEQTTS1;SEQIPR993E5041525449414C3C. The data is output as: >PARTIAL<TSTMSGCODE128<>MSGPDF417 [CR] [LF] Discard Partial Output Sequence If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence.
  • Page 79 To specify the timeout, use the SEQTIM command followed by a list of timeouts in milliseconds. Each timeout is specified as a 4-decimal digit terminated by FF. The timeout value 9999 is special and indicates that the timeout for that code is “infinite”.
  • Page 80 The command SEQSAT01FF23FF will satisfy the sequence if either Position 1 is scanned or Position 2 and 3 are scanned, it will send out the position 1 barcode or Position 2 and 3 barcode right away. SEQDFT;SEQ_EN1;SEQBLK62999943FF6A999954FF7299994DFF;SEQSEP993D3E;SEQSUF990D0A; SEQSAT01FF23FF;SEQTIM5000FF6000FF7000FF8000FF. Verify the below combination output sequence: 1.
  • Page 81: Require Output Sequence

    Default Output Sequence Default Sequence programs the scanner to all universal values. Be certain you want to delete or clear all formats before you read the Default Sequence symbol. Default Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device.
  • Page 82: Multiple Symbols

    * Good Read Click - Each Code in Sequence Good Read Beep - Partial Sequence Output * Error Tone - Partial Sequence Output Multiple Symbols When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger. If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping and or vibrating (if turned on) for each read.
  • Page 83: Video Reverse

    If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data Format beginning on page 79). The hex code for the No Read symbol is 9C. Video Reverse Video Reverse is used to allow the scanner to read barcodes that are inverted. The Video Reverse Off barcode below is an example of this type of barcode.
  • Page 84: Working Orientation

    Working Orientation Some barcodes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright. Upright: Vertical, Top to Bottom: (Rotate CW 90°)
  • Page 85: Optimized Scanning For Tobacco Products

    Optimized Scanning for Tobacco Products Tobacco codes are specialized Dot Code barcodes used on tobacco products in most of Europe and Data Matrix codes used on tobacco products in Russia. The following plug and play commands improve the scanning of these tobacco barcodes.
  • Page 86 Genesis XP User Guide...
  • Page 87: Chapter 4 - Data Edit

    CHAPTER DATA EDIT Prefix/Suffix Overview When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
  • Page 88: Add A Prefix Or Suffix

    • Enter prefixes and suffixes in the order in which you want them to appear on the output. • When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. •...
  • Page 89: Add A Carriage Return Suffix To All Symbologies

    Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in Symbology Charts, beginning on page 227) for the symbology from which you want to clear the prefix or suffix. Step 3.
  • Page 90: Function Code Transmit

    Clear All Suffixes Function Code Transmit By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 230). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted.
  • Page 91: User Specified Intercharacter Delay

    To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 241. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
  • Page 92: Intermessage Delay

    To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 241. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
  • Page 93: Chapter 5 - Data Format

    CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in barcode data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
  • Page 94: Show Data Format

    If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Show Data Format Scan the barcode below to show current data format settings. Data Format Settings Add a Data Format Step 1.
  • Page 95: Other Programming Selections

    Chart, beginning on page 241. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 82). Scan the symbols that represent the command you want to enter. Step 7.
  • Page 96: Terminal Id Table

    Save Discard Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your...
  • Page 97 Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code.
  • Page 98 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
  • Page 99 42 is the hex value for B The data is output as: 1234567890 Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
  • Page 100 1234567890**ABCDEFGHIJ <CR> Insert symbology name B3 Insert the name of the barcode’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 227). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 230 for decimal, hex and character codes.
  • Page 101 B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert barcode length” command F4 is the “Insert a character multiple times”...
  • Page 102: Move Commands

    If there are three keystrokes, the syntax would change from B5xxssnn for one keystroke to B5xxssnnssnnssnn. An example that would insert "abc" is as follows: B503001F00320030F833. Note: Key modifiers can be added together when needed. The sum is converted to hexadecimals.
  • Page 103: Search Commands

    FE and F7 Example: Manipulate barcodes that begin with a 1 Search for barcodes that begin with a 1. If a barcode matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return.
  • Page 104 F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: DEFGHIJ <CR> Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx”...
  • Page 105 Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”...
  • Page 106: Miscellaneous Commands

    Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
  • Page 107 If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns. Command string: E402300DF10D E4 is the “Replace characters”...
  • Page 108 EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters”...
  • Page 109: Data Formatter

    Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Discard Data B8 Discards types of data.
  • Page 110: Data Format Non-Match Error Tone

    requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. • Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format.
  • Page 111: Primary/Alternate Data Formats

    Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the barcodes below.
  • Page 112 Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 Genesis XP User Guide...
  • Page 113: Chapter 6 - Symbologies

    CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
  • Page 114: All Symbologies

    All Symbologies For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the symbologies you need by scanning the On barcode for each symbology. All Symbologies Off Message Length Description You are able to set the valid reading length of some of the barcode symbologies.
  • Page 115: Codabar Start/Stop Characters

    Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar barcodes with Modulo 16 check characters.
  • Page 116: Codabar Concatenation

    Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. A 1 2 3 4 D D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D”...
  • Page 117: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 139), you should disable Code Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode.
  • Page 118: Code 39 Message Length

    When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length...
  • Page 119: Code 32 Pharmaceutical (Paraf)

    Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Note: Trioptic Code (page 139) must be turned off while scanning Code 32 Pharmaceutical codes.
  • Page 120: Code 39 Code Page

    * Full ASCII Off Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting.
  • Page 121: Interleaved 2 Of 5 Message Length

    When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
  • Page 122: Nec 2 Of 5

    NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data.
  • Page 123: Nec 2 Of 5 Message Length

    NEC 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 <...
  • Page 124: Code 93 Append

    Code 93 Append This function allows the scanner to append the data from several Code 93 barcodes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 barcodes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data.
  • Page 125: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information.
  • Page 126: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA barcodes, you may want to adjust the redundancy count.
  • Page 127: Matrix 2 Of 5

    Maximum Message Length Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information.
  • Page 128: Code 11

    Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 barcodes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the barcodes below to change the message length.
  • Page 129: Code 128

    Code 128 <Default All Code 128 Settings> Code 128 On/Off * On If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 140), you should disable Code 128.
  • Page 130: Code 128 Message Length

    the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Code 128 Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 241.
  • Page 131: Gs1-128 Message Length

    Character Replacements on page 234), and scan the value and the Save barcode from the Programming Chart, beginning on page 241. The data characters should then appear properly. Code 128 Code Page GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the barcodes below to change the message length.
  • Page 132: Telepen

    Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).
  • Page 133: Upc-A

    Maximum Message Length UPC-A <Default All UPC-A Settings> UPC-A On/Off * On Note: To convert UPC-A barcodes to EAN-13, see Convert UPC-A to EAN-13 on page 126. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
  • Page 134: Upc-A Number System

    UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but can be programmed so it is not transmitted (Off). Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda.
  • Page 135: Upc-A Addenda Separator

    * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required.
  • Page 136: Coupon Gs1 Databar Output

    If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
  • Page 137: Upc-E0

    UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. barcodes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 125).
  • Page 138: Upc-E0 Addenda Separator

    Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
  • Page 139: Upc-E1

    UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
  • Page 140: Ean/Jan-13

    * UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A barcodes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
  • Page 141: Ean/Jan-13 Check Digit

    EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
  • Page 142: Beginning With 290 Addenda Required

    EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “290.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “290” must have a 5 digit addendum.
  • Page 143 Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “414”...
  • Page 144: Beginning With 977 Addenda Required

    Require 2 or 5 Digit Addenda EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “434”...
  • Page 145: Beginning With 978 Addenda Required

    Don’t Require 2 Digit Addenda: If you have selected Require 2 Digit Addenda, and you want to disable this feature, scan Don’t Require 2 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
  • Page 146: Ean/Jan-13 Addenda Separator

    Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
  • Page 147: Isbn Translate

    ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off. * Off EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether or not the check digit should be transmitted at the end of the scanned data.
  • Page 148: Ean/Jan-8 Addenda Required

    EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 barcodes that...
  • Page 149: Ean/Jan-8 Addenda Separator

    setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 241 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the barcode and the data from the addenda.
  • Page 150: Msi Check Character

    MSI Check Character Different types of check characters are used with MSI barcodes. You can program the scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI barcodes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
  • Page 151: Msi Message Length

    MSI Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional <...
  • Page 152: Gs1 Databar Limited

    GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information.
  • Page 153: Trioptic Code

    Maximum Message Length Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 105), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off If you are reading Code 39 barcodes, Codablock A should remain disabled.
  • Page 154: Codablock A Message Length

    Codablock A Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length Codablock F <Default All Codablock F Settings>...
  • Page 155: Label Code

    Maximum Message Length Label Code The standard Label Code is used in libraries. Default = Off. *Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Genesis XP User Guide...
  • Page 156: Pdf417 Message Length

    PDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 barcodes.
  • Page 157: Gs1 Composite Codes

    * Off MicroPDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new...
  • Page 158: Gs1 Emulation

    UPC/EAN Version Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off. UPC/EAN Version On * UPC/EAN Version Off Note: If you scan coupons that have both UPC and GS1 Databar codes, you may wish to...
  • Page 159: Tcif Linked Code 39 (Tlc39)

    If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC- E expansion is controlled by the UPC-E0 Expand (page 123) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts page 227).
  • Page 160: Qr Code

    QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On QR Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information.
  • Page 161: Qr Code Page

    Swipe: Pull and hold down the trigger and scan all appended QR Codes while keeping the trigger pressed. The scanner emits short beeps for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete.
  • Page 162: Dotcode

    Prohibit QR Code with Web Link Use this function to disable or enable the scanning of QR codes that contain “http” or “https”. (Prohibit QR codes with web links) (Allow QR codes with web links) DotCode < Default All DotCode Settings > DotCode On/Off * Off Poor Quality DotCodes...
  • Page 163: Digimarc Barcode

    * Poor Quality DotCodes Off DotCode Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-2400. Minimum Default = 1, Maximum Default = 2400. Minimum Message Length Maximum Message Length Digimarc Barcode™...
  • Page 164 When Digimarc Barcode is set to Uses ID Decoder then Alternates Decoders, the ID decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will alternate between ID and Digimarc decoders. When Digimarc Barcode is set to Uses Digimarc Decoder then Alternates Decoders, the Digimarc decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will alternate between ID and Digimarc decoders.
  • Page 165: Data Matrix

    Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Direct Part Marking Decoding If you are having trouble reading Direct Part Marking (DPM) barcodes, scan Dotpeen DPM Decoding for Dotpeen codes or scan Reflective (Etched) DPM Decoding for reflective (etched) codes Default = Disable DPM Decoding.
  • Page 166: Data Matrix Message Length

    Data Matrix Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length Data Matrix Code Page Data Matrix Code pages define the mapping of character codes to characters.
  • Page 167: Maxicode Message Length

    MaxiCode Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150. Minimum Message Length Maximum Message Length Aztec Code <...
  • Page 168: Aztec Append

    Aztec Append This function allows the scanner to append the data from several Aztec barcodes together before transmitting them to the host computer. When the scanner encounters an Aztec barcode with the append trigger character(s), it buffers the number of Aztec barcodes determined by information encoded in those barcodes. Once the proper number of codes is reached, the data is output in the order specified in the barcodes.
  • Page 169: Single 2D Postal Codes

    * Off Han Xin Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D...
  • Page 170: Combination 2D Postal Codes

    Intelligent Mail Barcode On Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 159. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 159. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British...
  • Page 171 Intelligent Mail Barcode and Postnet with B and B’ Fields On Postnet and Postal-4i On Postnet and Intelligent Mail Barcode On Postal-4i and Intelligent Mail Barcode On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’...
  • Page 172 Planet Code, Postnet, and Intelligent Mail Barcode On Planet Code, Postal-4i, and Intelligent Mail Barcode On Postnet, Postal-4i, and Intelligent Mail Barcode On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Barcode, and Postnet with B and B’...
  • Page 173: Planet Code Check Digit

    Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.
  • Page 174: Postal Codes - Linear

    Numeric N Table Alphanumeric C Table Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selections can be active at a time. China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings>...
  • Page 175: Korea Post

    Maximum Message Length Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 100) for additional information. Minimum and Maximum lengths = 2-80.
  • Page 176 * Don’t Transmit Check Digit Genesis XP User Guide...
  • Page 177: Chapter 7 - Imaging Commands

    CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and transfers images. The following commands allow you to alter the way the scanner performs these functions. Single-Use Basis Imaging Commands with their modifiers send instructions to the scanner on a single-use basis, and take effect for a single image capture.
  • Page 178: Step 1 - Take A Picture Using Imgsnp

    The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
  • Page 179 T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P). Takes image immediately (default) Waits for a trigger press, then takes the image L - LED State Determines if the LEDs should be on or off, and when.
  • Page 180: D - Delta For Acceptance

    G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
  • Page 181: Image Ship - Imgshp

    U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
  • Page 182: Imgshp Modifiers

    IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 164). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) Infinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
  • Page 183 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
  • Page 184: H - Histogram Stretch

    H - Histogram Stretch Increases the contrast of the transmitted image. Not available with some image formats. No stretch (default) Histogram stretch Example: Histogram Stretch at 0H: Histogram Stretch at 1H: I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example:...
  • Page 185: If- Noise Reduction

    IF- Noise Reduction Used to reduce the salt and pepper noise in an image. No salt and pepper noise reduction (default) Salt and pepper noise reduction Example: Noise Reduction Off (0if): Noise Reduction On (1if): IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left...
  • Page 186: K - Gamma Correction

    J - JPEG Image Quality Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50) Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)
  • Page 187 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
  • Page 188: U - Document Image Filter

    The smaller number of pixels shipped, the smaller the image, however, after a certain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Example: Pixel Ship set to 1S:...
  • Page 189: W - Histogram Ship

    V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
  • Page 190: Intelligent Signature Capture - Imgbox

    * Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a barcode. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the signature box location is in a known location relative to a barcode.
  • Page 191: Imgbox Modifiers

    To see this example, align the aimer with the signature area (not with the barcode), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
  • Page 192: B - Output Image Height

    B - Output Image Height This option is used to size the image vertically. If using this option, set the resolution (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
  • Page 193: H - Height Of Signature Capture Area

    H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
  • Page 194: W - Width Of Signature Capture Area

    decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 178). Example: Resolution set to 0R: Resolution set to 1000R:...
  • Page 195: Y - Vertical Barcode Offset

    Y - Vertical Barcode Offset The vertical barcode offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the barcode, and positive numbers indicate that the area is below the barcode. Measurements are in multiples of the minimum bar width.
  • Page 196 Genesis XP User Guide...
  • Page 197: Chapter 8 - Utilities

    CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 227 for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.
  • Page 198: Totalfreedom

    Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFreedom, go to our website at sps.honeywell.com. Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following barcodes.
  • Page 199: Ezconfig For Scanning Introduction

    Configure with EZConfig for Scanning Use the EZConfig for Scanning tool to configure your scanner online: 1. Access the Honeywell Technical Support Downloads Portal at https:// hsmftp.honeywell.com. 2. Go to Software > Barcode Scanners > Software > Tools and Utilities >...
  • Page 200: Reset The Factory Defaults

    Reset the Factory Defaults Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults barcode, then scan Activate Defaults.
  • Page 201: Chapter 9 - Serial Programming Commands

    CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming barcodes. Both the serial commands and the programming barcodes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming barcode in this manual. The device must be set to an RS232 interface (see page 10).
  • Page 202: Query Commands

    SubTag A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the SubTag for the RS232 baud rate is BAD. Data The new value for a menu setting, identified by the Tag and SubTag. Storage A single character that specifies the storage table to which the com- mand is applied.
  • Page 203: Concatenation Of Multiple Commands

    Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are issued.
  • Page 204: Trigger Commands

    Response: CBRENA1[ACK] This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on. Example: What are the device’s settings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK]. This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on;...
  • Page 205: Reset The Custom Defaults

    Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings.
  • Page 206: Menu Commands

    ACK/NAK Mode On USBACK1 *ACK/NAK Mode Off USBACK0 Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle PAPBTL Wincor Nixdorf RS232 Mode A...
  • Page 207 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Program Keyboard *U.S.A. KBDCTY0 Country Albania KBDCTY35 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium KBDCTY1 Bosnia KBDCTY33 Brazil KBDCTY16 Brazil (MS) KBDCTY59 Bulgaria (Cyrillic) KBDCTY52 Bulgaria (Latin) KBDCTY53 Canada (French legacy)
  • Page 208 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Hungary KBDCTY19 Iceland KBDCTY75 Irish KBDCTY73 Italian (142) KBDCTY56 Italy KBDCTY5 Japan ASCII KBDCTY28 Kazakh KBDCTY78 Kyrgyz (Cyrillic) KBDCTY79 Latin America KBDCTY14 Latvia KBDCTY42 Latvia (QWERTY) KBDCTY43 Lithuania KBDCTY44 Lithuania (IBM)
  • Page 209 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Tatar KBDCTY85 Turkey F KBDCTY27 Turkey Q KBDCTY24 Ukrainian KBDCTY76 United Kingdom KBDCTY7 United Stated (Dvorak right) KBDCTY89 United States (Dvorak left) KBDCTY88 United States (Dvorak) KBDCTY87 United States (International) KBDCTY30 Uzbek (Cyrillic)
  • Page 210 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 DOS Mode Control + X Mode On KBDCAS4 with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode...
  • Page 211 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout (1-5100 232DEL#### milliseconds) *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off...
  • Page 212 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry LED - Good Read BEPLED0 BEPLED1 Number of Beeps - Good Read (Range 1 - 9) *1 BEPRPT# Number of Beeps - Error (Range 1 - 9) *1 BEPERR# Good Read Delay *No Delay...
  • Page 213 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Presentation Centering Presentation Centering On PDCWIN1 *Presentation Centering Off PDCWIN0 Left of Presentation Centering PDCLFT### Window (*40%) Right of Presentation Centering PDCRGT### Window (*60%) Top of Presentation Centering PDCTOP### Window (*40%) Bottom of Presentation Centering...
  • Page 214 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Character Deactivation Mode *Off HSTDEN0 HSTDEN1 Deactivation Character (Range 0- HSTDCH### 255) *14 [DC4] Illumination Lights *Lights On SCNLED1 Lights Off SCNLED0 Aimer Delay 1 millisecond SCNDLY1 250 milliseconds SCNDLY250 500 milliseconds...
  • Page 215 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Terminate String Partial Sequence Transmit Partial Output Sequence SEQTTS1 Add Prefix to Partial Output SEQIPR Sequences Add Suffix to Partial Output SEQISU Sequences Add Separators to Partial Output SEQISE Sequences Terminate String...
  • Page 216 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Prefix/Suffix Selections Add CR Suffix to All Symbologies VSUFCR Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2...
  • Page 217 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Primary/Alternate Data Formats Primary Data Format ALTFNM0 Data Format 1 ALTFNM1 Data Format 2 ALTFNM2 Data Format 3 ALTFNM3 Single Scan Data Format Change Single Scan-Primary VSAF_0 Data Format Single Scan-Data Format 1 VSAF_1...
  • Page 218 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings...
  • Page 219 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Straight 2 of 5 Industrial Default All Straight 2 of 5 R25DFT Industrial Settings *Off R25ENA0 R25ENA1 Straight 2 of 5 Industrial Message Minimum (1 - 48) *4 R25MIN## Length Maximum (1 - 48) *48...
  • Page 220 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1-128 Default All GS1-128 Settings GS1DFT GS1ENA1 GS1ENA0 GS1-128 Message Length Minimum (1 - 80) *1 GS1MIN## Maximum (0 - 80) *80 GS1MAX## Telepen Default All Telepen TELDFT Settings *Off...
  • Page 221 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-E0 Default All UPC-E UPEDFT Settings UPEEN00 UPEEN01 UPC-E0 Expand *Off UPEEXP0 UPEEXP1 UPC-E0 Addenda Required Required UPEARQ1 *Not Required UPEARQ0 Addenda Timeout Range (0 - 500) *120 DLYADD##### UPC-E0 Addenda Separator UPEADS1...
  • Page 222 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN-13 Beginning with 378/379 *Don’t Require Addenda ARQ3780 Addenda Required Require 2 Digit Addenda ARQ3781 Require 5 Digit Addenda ARQ3782 Require 2 or 5 Digit Addenda ARQ3783 EAN-13 Beginning with 414/419 *Don’t Require Addenda ARQ4140...
  • Page 223 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Default All MSI Settings MSIDFT *Off MSIENA0 MSIENA1 MSI Check Character *Validate Type 10, but Don’t MSICHK0 Transmit Validate Type 10 and MSICHK1 Transmit Validate 2 Type 10 Chars, but MSICHK2 Don’t Transmit Validate 2 Type 10 Chars and...
  • Page 224 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Codablock F Default All Codablock F Settings CBFDFT *Off CBFENA0 CBFENA1 Codablock F Msg. Length Minimum (1 - 2048) *1 CBFMIN#### Maximum (1 - 2048) *2048 CBFMAX#### Label Code LBLENA1 *Off...
  • Page 225 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry QR Code Append *One Scan QRCAPP1 Swipe QRCAPP2 Point & Shoot QRCAPP3 QRCAPP0 QR Code Page QR Code Page (*3) QRCDCP## Prohibit QR Code with Web Link QRCWEB1 QRCWEB0 DotCode...
  • Page 226 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry MaxiCode Msg. Length Minimum (1-150) *1 MAXMIN### Maximum (1-150) *150 MAXMAX### Aztec Code Default All Aztec Code Settings AZTDFT AZTENA1 AZTENA0 Aztec Code Msg. Length Minimum (1-3832) *1 AZTMIN#### Maximum (1-3832) *3832 AZTMAX####...
  • Page 227 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Planet and Postnet with B and B’ POSTAL18 Fields On Planet and Postal-4i On POSTAL13 Planet and Intelligent Mail POSTAL15 Barcode On Planet, Postnet, and Postal-4i On POSTAL21 Planet, Postnet, and Intelligent POSTAL22...
  • Page 228 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Korea Post Default All Korea Post Settings KPCDFT *Off KPCENA0 KPCENA1 Korea Post Msg. Length Minimum (2 - 80) *4 KPCMIN## Maximum (2 - 80) *48 KPCMAX## Korea Post Check Digit Transmit Check Digit KPCCHK1...
  • Page 229 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry *File Format - JPEG IMGFMT6 File Format - KIM IMGFMT0 File Format - TIFF binary IMGFMT1 File Format - TIFF binary group 4, IMGFMT2 compressed File Format - TIFF grayscale IMGFMT3 File Format - Uncompressed IMGFMT4...
  • Page 230 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Document Image Filter On (0-255) IMGUSH### *Don’t Ship Histogram IMGHST0 Ship Histogram IMGHST1 Image Size Compatibility Force VGA Resolution IMGVGA1 *Native Resolution IMGVGA0 Intelligent Signature Capture Optimize On DECBND1 *Optimize Off DECBND0...
  • Page 231: Chapter 10 - Product Specifications

    CHAPTER PRODUCT SPECIFICATIONS Genesis XP 7680GSR Scanner Product Specifications Parameter Specification Mechanical Height 4.1 inches (105mm) / 5.7 inches (145mm) with stand Length 3.2 inches (80mm) Width 1.6 inches (40mm) Weight 12 ounces (340g) with stand 7.1 ounces (200g) without stand Electrical Voltage Requirements 5.0 VDC ±0.25V...
  • Page 232: Depth Of Field Charts

    Parameter (Continued) Specification Sealant Rating IP52 Image Image Size 1280 x 800 pixels Scan Performance Skew Angle 65° Pitch Angle 65° Motion Tolerance Up to 400 cm/s (158 in/s) for 13 mil UPC at optimal focus Symbol Contrast Depth of Field Charts 7680g Typical Performance Focus Standard Range...
  • Page 233: 7680G Guaranteed Performance

    20 mil QR Code Standard Connector Pinouts Note: The following pin assignments are not compatible with some Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
  • Page 234: Serial Output

    Serial Output 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power RS485 Output 10 Pin RJ41 Modular Plug - connects to the base Note: RS485 signal conversion is performed in the cable.
  • Page 235: Usb

    10 Pin Modular Plug - connects to the base Cable shield Cable select Supply ground +5V power Data + 10 Data - Required Safety Labels Illumination output Part Compliance Number, Serial Label Number and location Revision Information location Genesis XP User Guide...
  • Page 236 Genesis XP User Guide...
  • Page 237: Chapter 11 - Maintenance And Troubleshooting

    CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xiii). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following sections describe periodic checks to ensure dependable operation.
  • Page 238: About Disinfectant-Ready Models

    When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
  • Page 239: Troubleshoot

    Troubleshoot The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem. Is the power on? Is the aimer on? If the aimer isn’t illuminated, check that: •...
  • Page 240 Genesis XP User Guide...
  • Page 241: Chapter A - Reference Charts

    Refer to Data Edit beginning on page 73 and Data Format beginning on page 79 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Linear Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
  • Page 242: 2D Symbologies

    0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity 2D Symbologies...
  • Page 243: Postal Symbologies

    Honeywell Possible modifiers 2D Symbology Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix Dot Code GS1 Composite GS1 DataBar Omnidirectional...
  • Page 244: Ascii Conversion Chart (Code

    ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
  • Page 245: Lower Ascii Reference Table

    Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character <SPACE> " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
  • Page 246 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
  • Page 247 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code ┬ Â ├ Ã ─ Ä Å í ╞ Æ ╟ Ç ╚ È ╔ É ╩ Ê ╦ Ë ╠ Ì ═ Í ╬ Î ╧ Ï ╨...
  • Page 248: Iso 2022/Iso 646 Character Replacements

    (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
  • Page 249 Honeywell Code Page Selection Method/ Keyboard Code Standard Country Country Page Option Spain ISO/IEC 646-17 Spain ISO/IEC 646-85 Genesis XP User Guide...
  • Page 250 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ‾ ¥ ‾ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
  • Page 251: Keyboard Key References

    Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 252 Genesis XP User Guide...
  • Page 253: Sample Symbols

    SAMPLE SYMBOLS UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
  • Page 254 SAMPLE SYMBOLS (CONTINUED) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message DotCode 12345 Genesis XP User Guide...
  • Page 255: Programming Chart

    PROGRAMMING CHART Genesis XP User Guide...
  • Page 256 PROGRAMMING CHART (CONTINUED) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Genesis XP User Guide...
  • Page 258 Honeywell 855 S. Mint Street Charlotte, NC 28202 sps.honeywell.com ™ 7680-EN-UG-01 Rev C 11/22...

Table of Contents

Save PDF