Vacmaster VK809PWR 0201 Manual

Introduction

Feel confident that with Vacmaster ® you are obtaining a high-quality product engineered for optimal performance. This vacuum is capable of picking up liquids and dry materials.

GALLONS
"Tank Size"refers to the actual tank volume and does not reflect capacity available during operation.

PEAK HP
"Peak Horsepower" is a term used in the wet-dry vac industry for consumer comparison purposes. It does not denote the operational horsepower output of a wet-dry vac, but rather the horsepower output of a motor, including the motor's inertial contribution, achieved in laboratory testing. In actual use, motors do not operate at the peak horsepower shown.
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.

UNPACKING & CHECKING CARTON CONTENTS

Remove all contents from the box. Remove the powerhead and take out any contents inside the collection tank. Check each item against the carton contents list.

Carton Contents List:

Key	Description	Qty
A	Vacuum Assembly	1
B	Handle	1
C	Washable Cartridge Filter	1
D	Filter Retainer	1
E	Foam Wet Filter	1
F	Dust Collection Bag	1
G	Multi-Surface Floor Nozzle	1
H	Floor Brush/Squeegee Nozzle	1
I	Carpet Shampoo Nozzle	1
J	Handheld Shampoo Nozzle	1
K	Crevice Tool	1
L	Round Dust Brush	1
M	Extension Wand	1
N	Hose and Remote-Control Handle (with delivery tube attached)	2
O	Hub Cap	1
P	Washer	2
Q	'R' Lock Pin	4
R	Wheel Axle	2
S	Rear Wheel	1
T	Front Caster	2
U	Exhaust Filter	2
V	Hose Storage Rack	1
W	2 Screws (Bag)	2
X	Battery and Battery Cover	1
Y	Carpet Cleaning Solution	1
Z	Operator's Manual	1

NOTE: The hose and accessories for this vacuum are 35 mm diameter.

ACCESSORIES
A choice of accessories and attachments are supplied with this product. Refer to below descriptions for their functions.

Illustration	Description	Function
	Handheld Shampoo Nozzle	For cleaning sofas, chairs, stairs, and car interiors.
	Carpet Shampoo Nozzle	Used without brush holder for cleaning carpets.
	Crevice Tool	For cleaning edges, gaps, and tight spaces.
	Extension Wand	Used to connect accessories to the remote control handle and extend the cleaning reach.
	Multi-Surface Floor Nozzle	For cleaning hard surfaces and carpets. Use the tab on the top of the nozzle to release or retract the brush. For use on hard surfaces use the brush setting. For use on carpet, keep the brush retracted. NOTE: For dry vacuuming only.
	Floor Brush/Squeegee Nozzle	For cleaning dry and liquid messes on hard surfaces and low-pile carpets.
	Round Dust Brush	For cleaning fragile or easily scratched items, such as certain furniture or drapes.

GENERAL ASSEMBLY INSTRUCTIONS

A Phillips head screwdriver is required.

DO NOT PLUG THE POWER CORD INTO A POWER OUTLET. MAKE SURE THE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY SHAMPOO VACUUM. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO RAIN.

UNPACKING YOUR WET/DRY SHAMPOO VACUUM & GENERAL ASSEMBLY

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Undo the latches (Fig. 2).
   
3. Lift the powerhead off the collection tank (Fig. 3).
   
4. Remove the contents from inside the collection tank; make sure you have all contents as listed.

5. Turn the collection tank upside down and insert the two caster feet into the slots and apply pressure until they click into place (Fig. 4).
   
6. Insert the wheel axle into the rear wheel housing on the base. Insert a washer onto the axle followed by the rear wheel and another washer. Insert the 'R' lock pin into the hole on the end of the axle to lock into place. Snap the hub cap onto the wheel. Repeat the same steps on the other end of the axle (Fig. 5).
   
7. Insert the handle into the slots located on the top of the powerhead and secure it with the screws provided. Do not over-tighten the screws (Fig. 6).
   
8. Your vacuum comes ready for dry vacuum cleaning. If the cartridge filter is not installed, refer to 9 for installation instructions (Fig. 7 & 8).
   
9. Optional: For improved dust filtration, fit the dust collection bag flange onto the inlet port, taking care not to damage the bag (Fig. 9).
   NOTE: The dust collection bag is for dry pick-up only.
   
10. For wet vacuum cleaning, remove the cartridge filter, and install the supplied foam wet filter.
    See the foam wet filter installation instructions (Fig. 10).
    
11. Position the hose storage rack as illustrated. Squeeze the open sides of the hose storage rack inward. Insert the hose storage rack into the channel on the front side of the powerhead just above the top edge of the tank. Verify that the rack is secured in place as shown in (Fig. 11 & 12). Then squeeze in the other hose storage rack and insert it into the corresponding channel making sure it is secured.
    
12. Place the powerhead back on the collection tank aligning the top section with the latches, and snap into place (Fig. 13).
    
13. Ensure the end of the cleaning solution tube is securely fitted into the cleaning solution tank (Fig. 14).
    
14. A cleaning solution delivery tube runs along the hose with a threaded connector at the end. Insert the locking end of the hose into the vacuum port of the collection tank and turn clockwise to lock it into place. Connect the threaded connector on the end of the delivery tube onto the cleaning solution outlet coupling on the front of the powerhead (Fig. 15).
    
15. Lift the remote-control handle at the other end of the hose and insert the battery with the terminals in the direction as shown (Fig. 16).
    
16. Position the battery cover at the angle of inclination as shown. Then insert it into the slot on the battery compartment and press down the battery cover to click into place (Fig. 17 & 18).
    
17. Choose the desired accessory and/or the extension wand and connect it onto the remote-control handle (Fig. 19). The air flow regulation ( ) on the remote-control handle allows you to manually change the amount of vacuum suction (Fig. 20).
    

NOTE: If the suction power is too high when cleaning, adjust the air flow regulation to decrease the suction power (Fig. 20).

POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Double insulation eliminates the need for the three-wire grounded power cord and grounded power supply system.

PROGRAMMING THE REMOTE-CONTROL HANDLE
NOTE: The programming of the remote-control handle has been preset and is ready to be used in both vacuum and detergent mode. Reset the remote-control handle using the steps below if unable to operate in vacuum mode.

1. Ensure the vacuum is plugged into the power outlet.
2. Switch the on/off switch to the "I" ON position.
3. Locate the detergent mode button on the powerhead indicated by the following symbol
4. Press and hold the detergent mode button until the indicator light illuminates continuously (Fig. 21).
   

5. While the light is on, press and hold the detergent mode button on the remote-control handle until the indicator light on the powerhead starts to flash. The remote-control handle is now programmed to vacuum, and you should be able to operate in both detergent and vacuum modes (Fig. 22).
   
6. If the indicator light does not flash, repeat steps 1 to 5.

DRY VACUUM OPERATION

DRY VACUUMING

BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION ENTITLED "IMPORTANT SAFETY INSTRUCTIONS". DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUST IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO: LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASED PAINTS, GASOLINE, ALCOHOL, OR AEROSOL SPRAYS. EXPLOSIVE DUST INCLUDE BUT ARE NOT LIMITED TO: COAL, MAGNESIUM, GRAIN, OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.

DO NOT PLUG THE POWER CORD INTO A POWER OUTLET. MAKE SURE THE PLUG IS DISCONNECTED BEFORE CHANGING THE FILTERS.

DO NOT VACUUM DRYWALL DUST, FIREPLACE SOOT, OR ASH WITH STANDARD WET/DRY FILTER. THIS IS A VERY FINE DUST WHICH WILL NOT BE CAPTURED BY THE FILTER AND MAY CAUSE DAMAGE TO THE MOTOR. WHEN VACUUMING FINE DUST USE A FINE DUST FILTER (SOLD SEPARATELY).

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Your wet/dry shampoo vacuum comes with the cartridge filter pre-installed. In order to prepare your vacuum for dry vacuuming, make sure the cartridge filter completely covers the filter cage against the powerhead. For installation instructions, See (Fig. 2 & 3).
   
3. Place the filter retainer on the top of the cartridge filterand: tighten down by turning the retainer handle clockwise (Fig. 4).
   
4. Optional: For improved dust filtration, fit the dust collection bag flange onto the inlet port, taking care not to damage the bag (Fig. 5).
   
5. Place the powerhead back on the collection tank and secure it in place using the latches (Fig. 6).
   

OPERATING INSTRUCTIONS: DRY VACUUMING

6. Insert the locking end of the hose into the vacuum port on the collection tank and turn clockwise to lock into place (Fig. 7).
   
7. Choose the desired accessory and connect onto the remote-control handle or the extension wand (Fig. 8). The air flow regulation on the remote-control handle allows you to manually change the amount of vacuum suction.
   
8. Verify that the switch is in the 'O' OFF position before plugging the power cord into the power outlet. Plug the power cord into the outlet (Fig. 9 & 10).
   
9. Turn the motor on by flipping the switch to the 'I' ON position and the machine is ready for use. Press the vacuum mode button, indicated by the following symbol , on either the remote-control handle or the powerhead and operate the vacuum (Fig. 11).
   
10. Once you have completed vacuuming, switch off the vacuum by pressing the vacuum mode button on either the remote-control handle or the powerhead. Switch to the "O" OFF position and unplug the power cord from the power outlet.

O = OFF
I = ON
= VACUUM MODE
DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING. DO NOT USE THE DUST BAG FOR LIQUID VACUUMING.

LIQUID VACUUM OPERATION

1. Verify that the power cord is disconnected from the outlet. Make sure that the collection tank is clean and free of dust and dirt (Fig. 1).
   
2. Remove the cartridge filter, then carefully install the foam wet filter over the filter cage and place the power powerhead on the collection tank. For foam wet filter installation instructions, see (Fig. 2).
   

OPERATING INSTRUCTIONS: WET VACUUMING

3. Insert the locking end of the hose into the vacuum port on the collection tank and lock into place (Fig. 3).
   
4. Choose the desired accessory and connect onto the remote-control handle or the extension wand (Fig. 4). The air flow regulation on the remote-control handle allows you to manually change the amount of vacuum suction.
   
5. Verify that the switch is in the 'O' OFF position before plugging the power cord into the power outlet. Plug the power cord into the outlet (Fig. 5 & 6).
   
   
6. Turn the motor on by flipping the switch to the 'I' ON position and the machine is ready for use. Press the vacuum mode button, indicated by the following symbol , on either the remote-control handle or the powerhead and operate the vacuum (Fig. 7).
   
   DO NOT SUBMERGE THE REMOTE-CONTROL IN LIQUIDS.
   
7. Once you have completed vacuuming, switch off the vacuum by pressing the vacuum mode button on either the remote-control handle or the powerhead. Switch to the "O" OFF position and unplug the power cord from the power outlet.
8. After use, empty the collection tank by unscrewing the drain cap. Drain liquids into a suitable receptacle or drain (Fig. 8). Once the collection tank is cleaned and dried, refit the drain cap to the collection tank.
   

When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve that stops the suction action when the collection tank reaches its maximum capacity. You will notice an increase in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the liquid. To continue vacuuming, replace the drain cap. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the collection tank, clean, and dry the inside and outside before storage.
REMEMBER! The foam wet filter must be removed after wet vacuuming and the cartridge filter must be installed before dry vacuuming again.

CARPET/UPHOLSTERY CLEANING OPERATION

DO NOT RUN THE VACUUM IN DETERGENT MODE WITHOUT SOLUTION IN THE CLEANING SOLUTION TANK.

USE ONLY MANUFACTURER RECOMMENDED CLEANING SOLUTION WITH THIS VACUUM CLEANER.

DO NOT PLACE FURNITURE UNTIL THE CARPET IS COMPLETELY DRY!

BEFORE YOU USE THIS PRODUCT TO SHAMPOO CLEAN AN AREA, TEST YOUR WET/DRY SHAMPOO VACUUM AND THE CLEANING SOLUTION ON A SMALL HIDDEN AREA FOR COLORFASTNESS. IF THE COLOR IS AFFECTED, DO NOT USE.

THE CLEANING SOLUTION CONTAINS A CHEMICAL SOLUTION. AVOID PROLONGED CONTACT AS SOME INDIVIDUALS MAY EXPERIENCE SKIN AND EYE IRRITATION. FOR SKIN AND EYE IRRITATION, WASH AFFECTED AREA WITH WATER FOR 5-10 MINUTES. IF IRRITATION PERSISTS, SEEK MEDICAL ATTENTION IMMEDIATELY. INDIVIDUALS WITH SENSITIVE SKIN SHOULD WEAR RUBBER GLOVES. WASH HANDS THOROUGHLY AFTER USE. DO NOT INGEST. KEEP OUT OF REACH OF CHILDREN. USER ASSUMES ALL RISK.
NOTE: ALWAYS DRY VACUUM THE AREA BEING CLEANED BEFORE USING THE SHAMPOO MODE.

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. To prepare your vacuum cleaner for carpet/upholstery cleaning, remove the cartridge filter.
3. Carefully install the supplied foam wet filter over the filter cage, making sure the filter cage is completely covered. For foam wet filter installation instructions, see (Fig. 2).
   
4. Remove the cleaning solution tank from the vacuum base. Open the cap of cleaning solution tank and pour the cleaning solution mixture into the tank. To make the cleaning solution mixture, mix 1.5 oz. of cleaning solution per 0.5 gallon of water (Fig. 3).
   NOTE: A 17 oz. (500ml) bottle of cleaning solution is provided with this vacuum cleaner. Ensure the cleaning solution and water are mixed at the correct ratio. Water must be at room temperature.
   NOTE: Once depleted, the cleaning solution can be replaced by a high-quality liquid carpet cleaning solution that can be purchased from a local retailer. Always use the cleaning solution as directed by the manufacturer.
   

5. Snap the cap of cleaning solution tank back into place. Then insert the cleaning solution tank back into the vacuum base. Insert the end of the cleaning solution tube into the cleaning solution tank (Fig. 4).
   
6. Insert the locking end of the hose into the vacuum port on the collection tank and turn clockwise to lock into place. Connect the threaded connector on the end of the cleaning solution delivery tube onto the cleaning solution outlet coupling (Fig. 5).
   
7. Insert the remote-control handle and its cleaning solution outlet coupling () into the larger end of the extension wand and its cleaning solution inlet connector ( ) ensuring a "click" is heard. The air flow regulation on the remote-control handle allows you to manually change the amount of vacuum suction (Fig. 6 & 7).
   
8. Attach the carpet shampoo nozzle to the extension wand and make sure it clicks into place (Fig. 8 & 9).
   

For best performance, it is recommended to remove the brush holder during carpet cleaning.
Follow steps in Fig. 10. to remove the brush holder.

To re-install the brush holder, make sure to first align the arrows on the brush holder and the nozzle as shown. Then move the brush holder to the left as indicated by the arrow until you hear a "click" (Fig. 11).


NEVER PRY OR ROTATE THE SPRAY OUTLETS OF THE CARPET SHAMPOO NOZZLE AND HANDHELD SHAMPOO NOZZLE WITH A SCREWDRIVER OR ANY OTHER TOOL (FIG. 12 & 13).

MAINTENANCE

EMPTYING THE COLLECTION TANK

ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING THE POWERHEAD FROM COLLECTION TANK.

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Press down the yellow latch on the cleaning solution delivery tube and unplug the delivery tube from the vacuum. Then disconnect the hose from the vacuum (Fig. 2).
   
3. Disconnect the cleaning solution tube from the cleaning solution tank (Fig. 3).
   
4. Undo the latches and remove the powerhead from the collection tank (Fig. 4). Place the powerhead on a soft, clean surface upside down.
   
5. Clear all dirt or debris from the collection tank and hose into a proper waste container (Fig. 5).
   
6. Clean or replace the filters.
7. Check the hose, attachments, and power cord to ensure that they have not been damaged.
8. Place the powerhead back onto the collection tank and secure latches.

Clean or change the filter regularly for best performance. ALWAYS USE THE CARTRIDGE FILTER FOR DRY VACUUMING. If the machine is used without the cartridge filter, the motor will burn out and the warranty will be voided. Always keep spare filters on hand.

NOTICE! The filters included are made of high-quality materials designed to stop small dust particles. The cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary to pick up dust. If the cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle
the filter carefully when removing it for cleaning and replacing it. Check the filters for tears or small holes. A small hole can let dust pass through and out of the filter. Do not use a filter with holes or tears; replace it immediately.

STORAGE
Before storing your vacuum, the collection tank should be emptied and cleaned. The accessories should be cleaned and stored so they can be readily available when needed. Store the wet/dry vacuum indoors.

REPAIRS
Repairs for this wet/dry shampoo vacuum should be performed only by qualified service personnel using only identical replacement parts.

INSTALLING & CLEANING CARTRIDGE FILTER

INSTALLING CARTRIDGE FILTER

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Remove the powerhead and place in an upside-down position.
3. Install the cartridge filter over the filter cage making sure the cage is completely covered (Fig. 2 & 3).
   
4. Place the filter retainer on the top of the cartridge filter over the raised lip and tighten down by turning the retainer clockwise; do not over-tighten (Fig. 4 & 5).
   
5. Place the powerhead back onto the collection tank.

REMOVING & CLEANING CARTRIDGE FILTER

1. Unlock and remove the filter retainer by turning the retainer handle counter-clockwise (Fig. 6).
   
2. With the removed powerhead in an upside-down position, carefully remove the cartridge filter from the filter cage (Fig. 7).
   
3. Clean the cartridge filter by gently brushing or rinsing off the debris (Fig. 8). Cleaning should not be done indoors in living areas. For optimal performance a new filter is recommended.
   
4. Install cleaned or new filter as described in steps 2-4 of Installing Cartridge Filter.

INSTALLING & CLEANING FOAM WET FILTER

INSTALLING FOAM WET FILTER

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Remove the powerhead and place in an upside-down position. Follow instructions to remove the cartridge filter.
3. Carefully slide the foam wet filter down over the filter cage making sure the cage is completely covered (Fig. 2 & 3).
   
4. Place the powerhead onto the collection tank.

CLEANING FOAM WET FILTER

1. With the removed powerhead in an upside-down position, carefully remove the foam wet filter (Fig. 4).
   
2. Use a mild soap and water solution to wash the foam wet filter and rinse with clean water (Fig. 5).
   
3. Allow the wet filter to air dry completely before storing or installing onto the filter cage.

CLEANING & REPLACING EXHAUST FILTER

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Unlock the exhaust filter door by lifting the locking tab upwards to the release. Pull the door out (Fig. 2).
   
3. Remove the exhaust filter from the vacuum and clean by gently tapping or brushing off dirt. For optimal performance it is recommended to replace the old filter with a new filter regularly (Fig. 3).
   
4. Install the cleaned or new filter. Then insert the filter door tabs into the upper slots and lock the filter door into place (Fig. 4).
   

CHANGING THE BATTERY

NOTE: Only replace the battery with a 27A 12V Alkaline battery.

1. Verify that the power cord is disconnected from the outlet (Fig. 1).
   
2. Pry off the battery cover and remove it from the battery compartment (Fig. 2).
   
3. Remove the battery from the battery compartment. Insert the new battery with the terminals in the direction as shown (Fig. 3).
   
4. Position the battery cover at the angle of inclination as shown. Then insert it into the slot on the battery compartment and press down the battery cover to click into place (Fig. 4 & 5).
   

TROUBLESHOOTING

TO REDUCE THE RISK OF ELECTRIC SHOCK, UNPLUG BEFORE TROUBLESHOOTING.

EXPLODED VIEW

DOUBLE INSULATION INSTRUCTIONS

This Wet/Dry Shampoo Vacuum is double insulated, eliminating the need for a separate grounding system. Use only identical replacements parts. Read the instructions for Servicing Double- Insulated Wet/Dry Shampoo Vacuums before servicing. Use this vacuum as described in this manual. Observe the following warnings that appear on the motor housing of your vacuum.
DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.

TO REDUCE THE RISK OF ELECTRIC SHOCK - DO NOT EXPOSE TO RAIN. STORE INDOORS.

FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE OPERATOR'S MANUAL. DO NOT RUN UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE, OR OTHER HAZARDOUS MATERIALS. DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.

DO NOT VACUUM DRYWALL DUST, FIREPLACE SOOT, OR ASH WITH STANDARD WET/DRY FILTER. THIS TYPE OF DUST IS VERY FINE WHICH MAY NOT BE CAPTURED BY THE FILTER AND CAUSE DAMAGE TO MOTOR. WHEN VACUUMING FINE DUST USE A FINE DUST FILTER (SOLD SEPARATELY).

SERVICING OF DOUBLE-INSULATED WET/DRY SHAMPOO VACUUMS WITH A DOUBLE-INSULATED WET/DRY SHAMPOO VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE INSULATED WET/DRY SHAMPOO VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM, AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR A DOUBLE-INSULATED WET/DRY SHAMPOO VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE. YOUR DOUBLE-INSULATED WET/DRY SHAMPOO VAC IS MARKED WITH THE WORDS 'DOUBLE INSULATED' AND THE SYMBOL (SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE APPLIANCE.

EXTENSION CORDS

When using an extension cord with your Wet/Dry Shampoo Vacuum refer to the following table to determine the required A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good working condition. Make repairs or replacements before using the vacuum cleaner. Only use extension cords that are rated for outdoor use.

		Length of Extension Cord
120V		25ft (7.62m)	50ft (15.24m)	100ft (30.48m)	150ft (45.72m)
Ampere rating		A.W.G. Wire Size
More than	Not more than
0	6	18	16	16	14
6	10	18	16	14	12
10	12	16	16	14	12
12	16	14	12	Not recommended

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL	SIGNAL	MEANING
	DANGER	Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
	WARNING	Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
	CAUTION	Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
	NOTICE	(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Vacmaster VK809PWR 0201 Manual