Panasonic ER160 Manual
![]()
Before using the product
This clipper is designed for professional use to trim hair and beards. Charge for 8 hours before using the clipper for the first time in order to activate the built-in rechargeable batteries. The clipper can be operated on either an AC power source or a rechargeable batteries. Read all instructions carefully before use.
Parts identification
![Panasonic - ER160 - Parts identification Parts identification]()
(see fig. 1)
- On/Off switch
- Recharge lamp
- Charging status lamp
- Blade
- Dial (Height adjustment control)
Turn the dial clockwise or counterclockwise to adjust the moving blade back and forth to get the desired height. Adjustable in 5 stages from 1/32" (0.8 mm) to 5/64" (2.0 mm) in 1/64" (0.3 mm) steps without attachment (see fig. 4).
![Panasonic - ER160 - Using the Height adjustment control Dial Using the Height adjustment control Dial]()
- Trimming position mark
- DC input jack
- Short comb attachment
(1/8" - 5/32") - Medium comb attachment
(1/4" - 3/8") - Long comb attachment
(1/2" - 19/32")
Use these comb attachments to control the trimming height (see fig. 5).
![Panasonic - ER160 - Using the Long comb attachment Using the Long comb attachment]()
- Stationary blade
- Moving blade
- Cleaning hook
- Hook
- Power cord unit (RE5-92)
- Charging stand
- Charging stand input jack
- Comb attachment shelves
- Contact plug
- Cleaning brush
- Oil
READ ALL INSTRUCTIONS BEFORE USE.
Operation
How to charge and use as rechargeable unit
![Panasonic - ER160 - Charging the unit Charging the unit]()
Firmly insert the plug of the power cord unit
into the Charging stand input jack ![]()
Connect the power cord unit
to a power source.
Turn the On/Off switch
of the main unit to "Off" and place it on the contact plug
of the charging stand
to begin recharging. Confirm that the charging status lamp
is illuminated. (see fig. 2)
The charging status lamp
will blink in approximately one hour to signify the batteries have completely recharged. Once this is confirmed, remove the main unit from the charging stand
and turn the On/Off switch
to "ON" for use. The batteries will last approximately 50 minutes. The recharge lamp
indicates the power remaining in the batteries.
Recharge the batteries when it starts to blink. The unit can be used for approximately five minutes after the lamp begins to blink.
Using as a cord unit
![]()
Firmly insert the plug of the power cord unit
into the DC input jack
of the main unit.
Connect the power cord unit
to a power source (see fig. 3).
Turn the On/Off switch
of the main unit to "ON" for use.
In cases when the unit is having trouble to activate or the power is weak, turn the On/Off switch
to "Off" and recharge for approximately one minute before use.
How to use the comb attachments
To use the comb attachments always set the dial
to "1/32" (0.8 mm)".
Determine a desired trimming height and attach the relevant comb attachment.
Apply your thumb and remove each side of the comb attachment to disconnect (see fig. 5).
Blade care
![Panasonic - ER160 - Blade care instructions Blade care instructions]()
Hold the handle of the hair clipper firmly with the "Panasonic" name facing upward and push the upper part of the blade away from the housing (see fig. 6).
![]()
Using the brush, clean the blade block and depress the cleaning hook to open the blade in order to remove hair which may be caught between the blades (see fig. 7). Lubricate the space between the stationary and moving blades with 2 or 3 drops of oil after every few uses.
![]()
To reassemble, first, set the dial
to "5/64" (2.0 mm)", and reverse the above procedure, pushing the blade block until it clicks firmly into position (see fig. 8).
Special attention when charging
- Even though the clipper may not be used for an extended period, charge every six months to preserve battery life.
- Avoid charging the batteries at temperatures below 5°C (41°F) or above 35°C (95°F).
- Avoid charging the batteries in direct sunlight or near a radiating heat source.
How to remove the built-in rechargeable batteries
![Panasonic - ER160 - Removing the built-in rechargeable batteries Removing the built-in rechargeable batteries]()
- Remove the blade (a), peel off the finger grip (b) and take out one screw (c).
- Remove blade holder (d) and take out two screws (e).
- Remove the two rubber screw covers (f) and take out five screws (g).
- Remove each part, open the housing (h) and take out the two batteries (see fig. 9).
![burn hazard]()
![]()
![burn hazard]()
Do not attempt to replace the batteries for the purpose of reusing the clipper. This could result in the risk of fire or electric shock.
Specifications
Power source: 120 V AC, 60 Hz
Motor voltage: 2.4 V DC
Charging time: 1 hour
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this appliance.
![]()
To reduce the risk of electric shock:
- Do not reach for an appliance that has fallen into water. Unplug immediately.
- Do not use while bathing or in a shower.
- Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
- Always charge the clipper in a cool, dry place.
- Except when charging, always unplug this appliance from the electrical outlet immediately after using.
- Unplug this appliance before cleaning.
![burn hazard]()
![]()
![burn hazard]()
To reduce the risk of burns, fire, electric shock, or injury to persons
- Do not use this clipper with damaged clipper blades as injury may occur.
- Close supervision is necessary when this appliance is used by, on, or near children or invalids.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or dam aged, or dropped into water.
Return the appliance to a service center for examination and repair. - Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Always attach plug to appliance first, then to outlet. To disconnect, turn off the switch, then remove plug from outlet.
SAVE THESE INSTRUCTIONS
![burn hazard]()
![]()
![burn hazard]()
To prevent risk of fire, electric shock or personal injury, follow these instructions.
Do not allow permanent wave lotion, hair restorer or hair spray to come into contact with the main unit or the blades.
- Failure to observe this may result in cracking, discoloring or corrosion
- Always check blade and attachments for damage before each use. Replace them if damaged.
- Do not drop the hair clipper on the floor.
- Do not knock the blade and attachments against hard objects.
- Clean the housing using only a cloth slightly dampened with water or a mild soap solution.
- Never use a caustic solution.
- Never submerge the hair clipper in water.
- Keep out of the reach of children.
- Do not use to trim the hair of a pet.
- The hair clipper may become warm during operation and/or charging. This is normal.
- Avoid grabbing the hair clipper by the power cord, as it may become detached, causing damage or injury.
- Never tamper with moving parts.
- If the hair clipper is not working properly, have it inspected at an authorized service center.
- Use the ER160 hair clipper with the RE5-92 adaptor only.
- The recharge lamp may blink at an early stage when it is used for the first time or if it has not been used for six or more months even if after fully charged.
This is not a malfunction. Continue to use the clipper until the main body shuts down to restore operations back to normal. - The power cord unit can be mounted in a vertical or horizontal position.
Note:
The supply cord of the power cord unit RE5-92 cannot be replaced; if the cord is damaged, the adaptor should be discarded.
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Panasonic ER160 Manual
Need help?
Do you have a question about the ER160 and is the answer not in the manual?
Questions and answers