Chicco Baby Hug 4 in 1, Baby Hug 4 in 1 air - Crib Manual
![]()
INTRODUCTION
BABY HUG 4 IN 1 can be used as a crib, reclined cradle, high chair and first chair.
- Crib mode: suitable from birth until your child is able to sit up unaided (5-6 months), up to a maximum weight of 9 kg.
- Reclined cradle mode: suitable from birth until your child learns to sit up unaided (5-6 months approx., weighing a maximum of 9 kg).
- High chair: permitted when your child is able to sit up unaided (from 6 months approx.), up to 36 months and weighing a maximum of 15 kg.
- First Chair at the table mode: Permitted when your child starts walking and is able to sit down and stand up by himself (about 10/12 months, max. 18 kg).
COMPONENTS
The product is completely disassembled when purchased; check that all of the components listed below are present. If any part is missing contact ARTSANA's CUSTOMER SERVICES.
The product and all of its components must always be assembled by an adult.
![Chicco - Baby Hug 4 in 1 - Components Overview Components Overview]()
- A - Height adjustable pedestal frame
- A1 - 4 wheels with brakes
- A2 - Central support
- B - Seat frame
- C - Seat structure
- D - Tubular seat frame
- E - Fabric (with shoulder straps)
- F - Booster cushion
- G - Toy bar
- G1 - Light / sound game buttons
- G2 - 3 soft toys
- I - Upper fabric zips
- L - Plastic clips
- M - Height adjustment pedal
- N - Backrest recline lever
![]()
ASSEMBLY
The product is not assembled when purchased. To use it, carry out the following assembly operations:
- The first thing to do is assemble the "A1" wheels on height adjustable base frame "A". To do this place the frame on a rug or soft surface so as not to damage the floor or frame. Assemble the 4 "A1" wheels inserting the pins in the 4 holes under height adjustable base frame "A" as shown in figure 1.
![]()
![]()
Fully insert the wheel pin into the hole in the base. At this point the base can be rested on the floor. - Insert the fasteners of seat frame "B" into the respective tubes on seat structure "C" until they click into place.
![]()
- Assemble the seat (seat frame "B" + seat structure "C") on the base: insert the two tubes on base "A" into the corresponding holes on seat frame "B" until they click into place.
![]()
![]()
The backrest must face the height adjust ment pedal (I) as shown in Fig. 3a. - Insert tube "D" into the corresponding holes on seat frame "B" until they click into place.
![]()
- To assemble fabric "E" line up the holes on the fabric with the restraint system installed on seat structure "C". Pass the two lateral arms of seat frame "B" through the side fabric holes (FIG. 5), insert the pins of the arms into the holes on either side of the backrest (FIG. 5a) until they click into place.
![]()
![]()
![]()
Check that both arms are assembled correctly. - Attach fabric "E" using the two perimeter zips above seat frame "B".
![]()
- Pass the crotch strap and waist straps on seat structure "C" through the holes of fabric "E".
![]()
![Chicco - Baby Hug 4 in 1 - Assembly - Step 1 - Pass the crotch strap Assembly - Step 1 - Pass the crotch strap]()
- Attach the fabric (E) to the bottom of seat structure "C", making sure to insert all of the plastic clips in the right slots.
![Chicco - Baby Hug 4 in 1 - Assembly - Step 2 - Attach the fabric Assembly - Step 2 - Attach the fabric]()
- Press down on the lower part of the seat frame "C" until it locks to the tube on the frame "A".
![]()
![]()
- Insert the central support "A2" under the joint of the frame "A" (Fig. 10a-10b). Be sure that the product is not at its maximum height when carrying out this operation.
![Chicco - Baby Hug 4 in 1 - Assembly - Step 3 - Insert the central support Assembly - Step 3 - Insert the central support]()
BOOSTER CUSHION
- Reducer cushion "F" is ideal from birth and can be used or removed as necessary. To attach it to the seat, place it on the fabric, pass the crotch strap and waste straps through the holes in booster cushion "F" (reclined cradle mode), (Fig. 11). In high chair mode it is also necessary to pass the shoulder straps through the holes of the booster cushion (Fig. 11a).
![Chicco - Baby Hug 4 in 1 - Assembly - Step 4 - Booster cushion Assembly - Step 4 - Booster cushion]()
TOY BAR
- The toys can be attached to the toy bar by passing the straps through the plastic openings on the bar (Fig. 12) and fastening the velcro.
![]()
- Assemble the toy bar (with the light positioned towards backrest recline lever "N") inserting the pins of the bar into the holes on seat frame "B" until it clicks into place.
![]()
- To incline the toy bar in the three possible positions press the side buttons.
![]()
- To remove the toy bar press the buttons on the in side of the bar support and pull upwards.
![]()
![]()
This toy must be assembled by adults only.
![]()
Always check that the toy bar is properly fastened before using it.
![]()
To prevent possible injury by entaglement, remove this toy when the child starts trying to get up on its hands and knees in a crowling position.
HEIGHT ADJUSTMENT
- Once assembled, the product can be adjusted to various heights in all configurations. To adjust its height, hold down height adjustment pedal "M" (Fig. 16) and lift or lower the seat to the desired height.
![]()
ADJUSTING THE BACKREST
- The backrest can be adjusted to four different positions. To do this, push down on backrest recline lever "N".
![]()
Position 1 – Crib mode
![]()
Position 2-3 – Reclined cradle mode
![]()
Position 4 – High chair and first chair at the table mode
![]()
These adjustments can also be made with your child seated in the product. In this case it will be slightly more difficult.
![]()
Always check that the backrest is properly locked before use.
USING THE SAFETY HARNESS
- With fabric "E" assembled on seat structure "B", there will be a crotch strap, two waist straps and two shoulder straps.
![]()
- CRIB MODE
![]()
Completely remove all safety harnesses making sure to keep them out of the reach of your child.
![]()
- RECLINED CRADLE MODE
![]()
A 3-point restraint system must be used: crotch strap + waist straps.
![]()
- After placing your child in the seat, reclined cradle mode, fasten the straps by passing the two prongs through the crotch strap buckle; adjust the waist straps so that they fit closely around your child's waist.
![]()
- HIGH CHAIR
![]()
A 5-point restraint system must be used: crotch strap + waist straps + shoulder straps.
![]()
![]()
In this configuration the toy bar must always be positioned behind the backrest. - After placing your child in the seat in high chair mode, fasten the straps by passing the two prongs through the shoulder strap buckle (Fig. 23) and then through the crotch strap buckle (Fig. 23a); Adjust the height of the shoulder straps so that they correctly fit your child's shoulders.
![Chicco - Baby Hug 4 in 1 - Using The Safety Harness - Step 1 Using The Safety Harness - Step 1]()
Always make sure that the straps are fastened correctly. To unfasten the strap, press and pull the side prongs.
![]()
When using the product, always fasten the straps by inserting them in the crotch strap and check that they are tight enough and properly fastened. - FIRST SEAT AT THE TABLE MODE
![]()
Before using as a chair, remove the safety harness (crotch strap and waist belt) and position them in the relevant spaces (Fig. 24-24A-24B-24C-24D). Remove also toy bar or place it behind the backrest.
![Chicco - Baby Hug 4 in 1 - Using The Safety Harness - Step 2 Using The Safety Harness - Step 2]()
![Chicco - Baby Hug 4 in 1 - Using The Safety Harness - Step 3 Using The Safety Harness - Step 3]()
- Adjust the seat to the desired height as indicated in point 16 of the HEIGHT ADJUSTMENT paragraph, the backrest must be completely raised, as indicated in point 17 of ADJUSTING THE BACKREST paragraph.
![]()
Always check that the backrest is properly locked before use.
![]()
When the product is in use, all four casters must be braked. - The safety harness straps can be removed (for washing or for use in the crib/reclined cradle configuration).
To remove the harnesses pull the waist and crotch straps out from the holes in the fabric (Fig. 24-24a-24b) until they are hidden on the seat frame and pull the shoulder straps out from the fabric holes on the backrest (Fig. 24c-24d). After removing the safety harnesses, make sure that the harnesses are correctly re-assembled.
To re-assemble the safety harnesses, carefully follow the steps below: - Follow point 7 of the ASSEMBLY paragraph to re-assemble the waist straps and crotch strap. For the shoulder straps, pass the strap through the hole as shown in Fig. 25, making sure that the length adjuster is positioned as shown in the figure.
![]()
Take the plastic hole of the shoulder straps and pass it through the fabric ring of the harness.
![]()
Having performed this operation correctly, pull the harness downwards until the fabric ring is turned inside out.
![Chicco - Baby Hug 4 in 1 - Using The Safety Harness - Step 4 Using The Safety Harness - Step 4]()
Once assembled, the belts must be adjusted once again according to the size of your child.
BRAKES
- All 4 wheels have brakes; to activate the brakes push down the little lever on the wheels.
![]()
![]()
When the product is in use, all 4 wheels must be locked at all times.
To release the brakes push the little levers on the wheels upwards.
![]()
TOY BAR WITH LIGHTS AND SOUNDS
- The toy bar comes complete with a sounds and lights panel that is activated by pressing the buttons on the upper section.
![]()
F1: On button - volume
F2: Plays fun music
F3: Plays lullabies
F4: The lights come on
WARNINGS REGARDING TOY BAR ELECTRICAL PARTS
![]()
Dispose of used batteries immediately. Keep new and used batteries away from children. If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.
- To insert or change the batteries: loosen the screw on the toy bar battery compartment cover with a screwdriver and open (FIG. 28). Remove the flat batteries and fit new ones, making sure that the battery polarity is correct (as shown on the product); close the battery compartment cover and tighten the screw firmly (2 x 1.5 V AA batteries).
- Batteries must only be replaced by an adult.
- Only use alkaline batteries of the same type or equivalent to the type recommended for this product (2 x 1.5V AA batteries).
- Make sure the battery polarity is correct.
- Never mix new and old or different types of batteries.
- Always keep batteries and tools out of the reach of children.
- Do not short-circuit the power terminals.
- Always remove flat batteries from the product to prevent any possible liquid leaks from damaging it.
- Always remove the batteries if the product will not be used for a long period of time.
- Remove the batteries from the toy bar before disposing of the product.
- Do not throw dead batteries in fire or leave them in the environment; they must be disposed of through waste sorting.
- If the batteries are leaking liquid, replace them immediately, making sure to clean the battery compartment; thoroughly wash your hands if they have come into contact with the liquid.
- Always dispose of leaking batteries immediately: they can cause burns or other types of injuries.
- Do not try to recharge non-rechargeable batteries: they may explode.
- The use of rechargeable batteries is not recommended as the toy may not work properly.
- If using rechargeable batteries, remove them from the toy before recharging them.
- Do not leave the product outside in the rain; water will damage the electronic circuit.
- Rechargeable batteries must be charged only under adult supervision.
REMOVING THE COVER
- To remove the cover from the frame of the product, put the seat in the horizontal position (crib) and unfasten the plastic clips from the seat structure. To do this it is necessary to push the tab inwards and pull the clip down, repeating this procedure for all clips.
![]()
- Pull the restraint system out through the fabric holes (if present), see SAFETY HARNESS paragraph.
- Undo the zips along the upper edge.
![]()
- Disassemble the lateral arm, pushing the pin inwards and pulling the arm in an outwards direction (Fig. 31). Repeat this procedure for the other arm. Lift the arm (Fig. 32) and remove from the fabric (Fig. 32a).
![Chicco - Baby Hug 4 in 1 - Removing The Cover Removing The Cover]()
CLOSING THE PRODUCT
- To close the product for storage purposes press down on backrest recline lever "N", put the backrest in a completely horizontal position and remove the toy bar by pressing the buttons (Fig. 33). Completely lower the seat by pressing on height adjustment pedal "M".
![]()
![]()
The reclined cradle must never be closed with a child sitting in it. Remove your child from the product before closing the frame.
TIPS FOR CLEANING AND MAINTENANCE
Please refer to the care label for instructions on washing the product:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
- Check that the fabric and stitching are in good condi-tion each time you wash it.
- Prolonged exposure to direct sunlight can cause the fabric to fade.
CLEANING
Clean the plastic parts with a soft damp cloth. Never use abrasive detergents or solvents. If the high chair comes into contact with water, dry the metal parts to prevent the formation of rust.
MAINTENANCE
- This product requires periodical maintenance.
- Cleaning and maintenance operations must only be carried out by an adult.
- Periodically check the product for broken, damaged or missing parts: do not use it in this case.
- To avoid friction that may compromise the correct functioning of the product, ensure that all the moving plastic parts located along the metal frame are free of dust, dirt and sand.
- If necessary, lubricate the moving parts with dry silicone lubricant.
- Store the product in a dry place.
WARNINGS
![]()
Only for domestic use. ![]()
TO AVOID DANGER OF SUFFOCATION REMOVE THIS PLASTIC COVER BEFORE USING THE PRODUCT. THIS COVER SHOULD BE DESTROYED OR KEPT AWAY FROM BABIES AND CHILDREN. ![]()
Never leave the child unattended. ![]()
Do not allow other children to play unsupervised near the product. ![]()
The product and all of its components must always be assembled by an adult. ![]()
Do not attach any strings to extend the fastening systems of the toy bar's hanging toy and do not make knots/loops: this may cause the accidental formation of slip knots that could cause strangling hazards. - Prolonged exposure to direct sunlight may cause the product colours to fade. After prolonged exposure of the product to high temperatures, wait a few minutes prior to putting your child in it.
- Make sure that the person using the product knows how to do so in the safest way.
- Never use the product without its cover.
- Do not use the product with more than one child at a time.
- Do not leave small objects on the product that could be swallowed by children.
- The product must only be opened, adjusted and closed by an adult.
- Always place the product on a horizontal, stable surface when your child is seated in it.
- Never place the product near stairs or steps or on carpets.
- Do not hang bags or weights on the product frame as this may affect its stability.
- Do not open and close the product when your child is sitting in it.
- Before assembly, check that neither the product nor any of its components have been damaged during transportation. In this case, do not use and keep out of reach of children.
- Do not use accessories or replacement parts other than those approved by the manufacturer.
![]()
This product must only be used under adult supervision. - When the product is being used, the wheels must always be locked.
![]()
Regularly inspect the product for signs of wear and damage. Should any parts on the toy bar or hanging toy be damaged, do not use them and keep out of reach of children. - Keep the product out of reach of children when it is not in use.
0 - 6 MONTHS CRIB MODE
![]()
When in crib mode, completely remove the safety belts making sure they are kept out of your child's reach.
Do not use this product with out reading the instructions for use first.
The product is intended for use by children aged 0 to 6 months, weighing a maximum of 9 kg.
Stop using the product as soon as the child can sit or kneel or pull itself up.
Placing additional items in the product may cause suffocation. - The product must always be placed on a horizontal surface. Never leave the product on a sloping surface with your child inside.
The product is ready for use only when all locking mechanisms are engaged. Make sure they are securely engaged before use.
Do not use the crib if any part is broken, torn or missing.
DO NOT USE the product in "Crib Configuration" and if any part is missing, dam aged or broken. Contact Artsana SpA for spare parts and user instructions if needed. DO NOT REPLACE missing, damaged or bro ken parts with non-OEM components or components not approved by Artsana SpA.
Be aware of the risk of burns from cigarettes, naked flames and other heat sources, like electric or gas heaters, that are near the crib. - All components must be firmly fixed in place at all times; also make sure that there are no open zippers as your child's body parts or clothing could get caught in them (laces, necklaces, pacifier chains etc.), constituting a strangulation hazard.
- Do not use the body of the crib without its frame.
- When the product is being used, the wheels must always be locked.
- The thickness of the mattress must be such that the vertical height (upper surface of the mattress until the upper edge of the product's sides) is at least 200 mm.
Do not place the product close to another product, which could present a danger of suffocation or strangu lation, e.g. strings, blind/curtain cords, etc To avoid strangulation hazards, never give children objects with strings attached, or leave these objects within their reach.
Do not use more than one mattress in the product. Only use the mattress supplied with the crib.
Only use the mattress sold with the crib. Do not add a second mattress, choking hazard. Dimension mattress 750 x 380 x 30 mm.
Newborn babies can suffocate on soft bedding. Avoid placing pillows or similar items under newborn babies for additional comfort during sleep. - Do not leave anything inside the product that might reduce its depth.
- To prevent the child being trapped, do not place the crib close to walls of obstacles.
- The product must be kept away from electrical cables and cords: do not position close to windows where cords, curtains or similar could pose a suffocation or choking hazard. To avoid all risks of strangulation, never give children objects with cords or strings attached, or leave them within their reach.
0 - 6 MONTHS RECLINED CRADLE MODE
![]()
Stop using the product when the child starts trying to sit up.
Age range: from birth to 9 kg (6 months).
Always use the restraint system. - Always use the restraint system when your child is in the reclined cradle; adjust the length of the straps as necessary.
Never use the toy bar to carry the product.
Do not move or lift this product with the baby inside it.
Never let the child sleep in this product. This product does not replace a cot or a crib. Should the child fall asleep, then it should be placed in a suitable cot or crib.
Do not use the reclined cradle if any components are broken or missing. - Never leave the reclined cradle on surfaces that are not perfectly horizontal.
- To prevent fire hazards, do not leave the reclined cradle near sources of heat, electrical or gas devices etc.
- Make sure that all parts are correctly hooked to the mounts.
- Periodically check for any worn parts, loose screws, worn or unstitched materials and replace any damaged parts immediately.
- Do not place the reclined cradle with your child in it near windows or walls where strings, curtains or other objects could be used by the child to climb or pose choking or strangling hazards.
- To avoid the risk of your child overbalancing and falling do not place the reclined cradle near windows or walls.
6 - 36 MONTHS HIGH CHAIR
![]()
In this configuration the toy bar must always be positioned behind the backrest.
Always use the restraint system.
Falling hazard: Prevent your child from climbing on the product.
Do not use the product unless all components are correctly fitted and adjusted.
Be aware of the risk of open fire and other sources of strong heat in the vicinity of the product.
Be aware of the risk of tilting when your child can push its feet against a table or any other structure.
Make sure that any harness is correctly fitted before using.
Always check the safety and the stability of the high chair before use.
Before using, ensure that all the safety devices are fitted and working correctly. In particular, make sure that the high chair is locked in the open position.
Always apply the parking device when it is not being moved. - Do not use the high chair until the child can sit up unaided.
- The high chair is intended for use for children who can sit up alone and are between 6 and 36 months of age, weighing up to 15 kg.
- Do not use the high chair if any part is broken, torn or missing.
- Make sure your child is at a safe distance when opening and closing the product. Make sure that during adjustment operations (tilting the backrest) the adjustable parts of the high chair do not come into contact with your child.
- The use of the safety harness with fabric crotch strap correctly fastened to the seat and with crotch bar is necessary to ensure the safety of your child when the chair is used as a high chair.
- Never move the high chair with your child seated in it.
- Do not allow other children to play unsupervised near the high chair, or allow them to climb it.
- Do not place the high chair near windows or walls where strings, curtains or other objects could be used by the child to climb or pose choking or strangling hazards.
12 M+ FIRST CHAIR MODE
- Age range intended for use: From when your child starts walking and is able to sit down and stand up by himself (about 10/12 months, max. 18 kg).
Before using as a chair, remove the safety harness (crotch strap and waist belt) and position them in the relevant spaces. Remove also toy bar or place it behind the backrest.
Chair must be used with the backrest completely raised.
Never leave the child unattended.
DO NOT place this product near a window as it can be used as a step by the child and cause the child to fall out of the window.
Be aware of the risk of open fires and other sources of strong heat in the vicinity of the product.
DO NOT place this product near a window where cords from blinds or curtains could strangle a child.
Do not use the product if any components are broken, torn or missing.
Do not use accessories or replacement parts other than those approved by the manufacturer. - Place only on flat and stable surfaces.
Check that the space where the chair will be used is free of objects or furniture that may obstruct the product or compromise its correct use. - Do not let your child stand up on the chair to avoid the risk of falling.
- Do not allow more than one child at a time to sit on the chair in order not to compromise its stability.
- This chair is intended solely for domestic use and on dry surfaces.
- Do not make any modifications: any modification may prejudice its safety.
- Prolonged exposure to direct sunlight can cause the fabric to fade. After prolonged exposure to high temperatures, wait a few minutes before using the product.
- Never move the chair while the child is seated on it.
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Chicco Baby Hug 4 in 1, Baby Hug 4 in 1 air - Crib Manual
Need help?
Do you have a question about the Baby Hug 4 in 1 and is the answer not in the manual?
Questions and answers