Lippert Glass Rinser - Rinser Manual

Introduction

The Glass Rinser is another tool from Lippert Components, Inc. to provide assistance and convenience for our customers' camping experience.
This manual covers the operation of the Glass Rinser. The components may differ based on the unit's year, make, model and floor plan, but operate in the same manner.
If you have any questions about the Glass Rinser, please contact the Lippert Customer Care Center: https://support.lci1.com/.
Additional information about this product can be obtained from lci1.com/support or by downloading the free LippertNOW app. The app is available on Apple App Store® for iPhone® and iPad® and also on Google Play™ for Android™ users.
Apple App Store®, iPhone®, and iPad® are registered trademarks of Apple Inc. Google Play™ and Android™ are trademarks of Google Inc.
For information on the assembly or individual components of this product, please visit:
Kitchen/Lippert Customer Care Center (lci1.com).
NOTE: Images used in this document are for reference only when assembling, installing and/or operating this product. Actual appearance of provided and/or purchased parts and assemblies may differ.

Prior To Use

1. Confirm the water source is connected to the RV, i.e. campground hookup or fresh water tank.
2. Check for leaks on the counter and in the cabinet under the kitchen sink.
3. The Glass Rinser base (Fig. 1) outlet should be aligned with the sink and slightly overhangs the sink edge.
   
4. Be sure the supply fitting under the sink (Fig. 3) is connected to the Glass Rinser (Fig. 2) and turned to the ON position (Fig. 4A).
   
   
   

Operation

1. Place the glass or cup to be cleaned open side down on the actuator arm. NOTE: For best results, be sure to center the glass on the actuator arm.
2. Placing a hand on the bottom of the glass, push downward firmly, activating the spray nozzle in the center of the actuator arm.
3. Hold the glass in place until clean. NOTE: In the event residue is dried in the glass, a bit of dish washing liquid can be dropped into the glass. Run a rinse cycle as usual, starting with Step 1.
4. Release the pressure on the bottom of the glass, allowing it to rise up from the Glass Rinser base.
5. The water will shut off when the actuator arm is released.
6. If the inside of the glass is not clean, repeat the process from Step 1. NOTE: The Glass Rinser is designed to rinse and clean the inside of a glass or cup. Be sure to check the glass for residue that may be on the outside of the glass. Clean with a dish cloth, sponge or scrub pad. NOTE: As needed, actuator arm can be removed for cleaning.

Troubleshooting

Safety

Read and understand all instructions before installing or operating this product. Adhere to all safety labels.

This manual provides general instructions. Many variables can change the circumstances of the instructions, i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This manual cannot begin to plot out instructions for every possibility, but provides the general instructions, as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the provided instructions may result in death, serious personal injury, severe product and/or property damage, including voiding of the Lippert limited warranty.

The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death or serious personal injury if not performed safely and within the parameters set forth in this manual.

Failure to follow instructions provided in this manual may result in death, serious personal injury and/or severe product and property damage, including voiding of the component warranty.

The "CAUTION" symbol above is a sign that a safety risk is involved and may cause personal injury and/or product or property damage if not safely adhered to and within the parameters set forth in this manual.

Unit MUST be winterized per manufacturer's recommendations. Failure to winterize the unit could damage the faucets and other plumbing system components. Please see TI-492

Always wear eye protection when performing service, maintenance or installation procedures. Other safety equipment to consider would be hearing protection, gloves and possibly a full face shield, depending on the nature of the task.

Ph: 432-LIPPERT (432-547-7378)
Web: lippert.com
Email: customerservice@lci1.com