Advertisement
Charge the Doorbell
Please charge your doorbell with a DC 5V 1A~2A phone adapter and the provided charging cable. The LED will glow blue once fully charged.
Supply Power to the Chime
Power by three AA batteries
Three units of AA batteries is required to make your indoor chime 100% wire-free. And you will be free to place your chime in almost anywhere indoors. *Please mind the electrodes when installing batteries!
Power by DC 5V adapter
You can also plug in the provided USB cable and connect the chime to DC 5V 1A~2A phone adapter.
What's in the Box
Doorbell * 1
DingDong *1
Quick User Guide *1
USB Cable *1
Screws Set/Screwdriver *1
3M Tape *2
NOTE: Micro SD card and power adapter are not included.
Switch on the Doorbell
Remove the wall mounting bracket and silicone cover, switch on your doorbell. The LED indicator will flash red (once per second), and it is ready for network setting.
 | Solid Red Device is abnormal |
 | Flashing Red Slowly (Once per second) Ready for WiFi configuration |
 | Flashing Red Quickly (Twice per second) Device is connecting to WiFi |
 | Solid Blue Successfully connected to WiFi network |
 | Flashing Blue Slowly (Once per second) Live-viewing doorbell camera |
 | Flashing Blue Quickly (Twice per second) Upgrading doorbell firmware |
Download and Install App
Download Mubview App from Google Play™ or App Store™. Or scan the QR codes as below, with your smart phone. *Google Play™ is a trademark of Google Inc. App Store™ is a mark of Apple Inc.
iOS
Android
NOTE: Make sure turning on both permissions below.
- Allow Mubview App to access mobile cellular data and wireless LAN, otherwise it will fail to connect the camera (in mobile Setting).
- Allow Mubview App to send messages, otherwise the phone will not receive alarms when motion is detected (in mobile Setting-Mubview).
Account Registration
New user needs to sign up in Mubview App with email address. Click 'Sign up' to create a New Account and follow the steps to complete registration.
Add Doorbell to App
Preparations for connection
- Insert Micro SD Card into the camera to save video clips or you can start the 3-day free cloud service. Without Micro SD Card or cloud service, no video will be saved.
- The camera only support 2.4GHz Wi-Fi, not support 5GHz.
- When connect to the network, please take the camera close to the router(suggest within 10-15ft).
Connect Doorbell to App
Tap 'Add Device'
Select 'Doorbell Camera'
Power on the Camera
Reset the Camera
Activate the doorbell
Prepare to Scan
Scan QR Code
Wait till 100%
Perform Network Diagnosis
Connect the Chime
Click reset button
Click RESET on the chime, and the chime indicator on the left will flash red for 20 seconds, indicating that the chime is in pairing mode.
Press your doorbell to pair up
Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds.
NOTE: If your home is large and you need more than one Dingdong, please buy it on Amazon or contact Mubview team to get extra 2.
Chime settings
 | Ringtone selection Click change ringtone (4 ringtones available) |
 | Volume control button Level 1: 110 dB; Level 2: 100 dB; Level 3: 90 dB; Level 4: 80 dB |
 | Settings Click to enter/quit pairing mode; Press & hold 5 seconds to restore factory defaults |
NOTE: If you need 3-day overwriting cloud storage for half a year for free, please contact us to get it.
Email: support@mubview.com
Install the Doorbell
Select a location
You can purchase the following angled brackets so as to point your doorbell to a specific view angle.
Mark the screw holes & Install the wall mount
- Take apart the wall mount from your doorbell and mark the location of the two mounting holes on your wall.
![Install the Doorbell - Step 3]( "MUBVIEW - Bell-J7 - Install the Doorbell - Step 3")
- Screw your bracket into wood wall with the provided screws. If installing on stucco, brick, or concrete, drill holes in the wall, then insert the included anchors before driving in the mounting screws.
![]()
Mount your doorbell
Attach your doorbell to the mounting bracket and snap the doorbell to make sure it reaches the bottom. Then secure it with the provided starsharpped security screw.
Tamper Alart Setting
Kindly notice the anti-theft alarm in doorbell settings.
 | Tamper Alert on Once the doorbell is detached from the bracket, a 30-sec alarm will be triggered. Meanwhile, video recording will be activated, and alarm notification will be pushed to the owner's APP account. |
 | Tamper Alert off The owner can disable the tamper alarm in doorbell settings, and detach the doorbell for battery recharging or maintainance. |
Product Specifications
Video Doorbell Model No.: Bell J7
Wireless Chime Model No.: Chime 06
Product Service
Email: support@mubview.com
Distributor: business@mubview.com
About Us
Web: www.mubview.com
Facebook: www.facebook.com/mubview
Amazon Store: www.amazon.com/mubview
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the Bell-J7 and is the answer not in the manual?
Questions and answers