bioBidet Slim Zero - Toilet Manual

Configuration

Product

Parts List

1. Main body
   
2. Installation components
   Method 1
   
   Method 2
   
   Note:
   There are two methods for installation. The recommended way is using the rubber expansive nuts. The second option is using the butterfly nuts. Please select the option best suited for your specific installation needs.
3. T-Valve adapter
   
4. Bidet supply hose
   
5. User manual

Installation

Please make sure you read the instructions carefully and install it properly.

1. The water pressure limit is from 10 to 110 PSI. Please use as instructed.
2. The water shutoff valve should be near where the product is installed.

Product Installation Procedure

Pre-installation

1. Insert the mounting bolts into the rectangular steel mounting brackets.
   
2. Insert the mounting bolts with the brackets into the catch plate.
   
3. Example of how the bolts fit through the mounting brackets and how they are placed onto the catch plate and secured to the toilet.
   

First installation method (recommended)

1. Completely remove the old toilet seat & lid
   
2. Install expansion nuts. Be sure to firmly press down so the top of the expansion nut is flush with the ceramic toilet surface.
   
3. Attach the catch plate
   
   • Attach the catch plate in the toilet seat holes. Adjust the position of mounting bolts and adjusting pieces to line up the mounting bolts to the expansion nuts. Then tighten to secure the catch plate.
     
4. Install the bidet seat
   • Line up the bidet with the catch plate then push the bidet seat onto the catch plate. You will hear the bidet seat click into the place.
     

Second installation method

1. Remove the old toilet seat.
   Refer to first installation method step 1.
2. Put the catch plate over the toilet seat mounting holes in the ceramic of the connecting bolts with adjusting pieces. Screw on the nuts from underneath the toilet. Then tighten to secure the catch plate. Refer to the first installation step 3.
3. Install the bidet seat, Line up the bidet with the catch plate, you will hear the seat click into place

Connecting Water Supply

1. Close the water supply valve. Flush toilet.
   
2. Unscrew water supply hose from water tank. Place towel below tank to catch any dripping water.
   
3. Using finger nut, attach T-Valve to water tank where you removed the water supply hose.
   
4. Re-attach water supply hose to bottom of T-Valve.
   
5. Connect the bidet supply hose to the metal inlet on the side of the bidet seat. Connect the other end of the hose to the T-Valve and tighten snugly. Be careful not to over-tighten.
   
6. Slowly open the water valve to check if there is any water leakage.
   
7. Wipe the hoses and connectors thoroughly with a towel and carefully observe for any leaks for at least 10 minutes. Tighten any connectors gently until leakage stops. If any leaks continue, turn off water supply and check older hoses for damaged rubber o-rings. Teflon tape may be used on connections to help seal.

Operation

STOP

• Return the lever to the upright position to turn it off.
  

BIDET (FRONT FEMININE WASH)

• Gradually push control lever forward until preferred pressure is reached.
  

REAR WASH

• Gradually push control lever back until preferred pressure is reached.
  

Night-Light Instructions

Installing the Battery

Remove the battery pack

Insert 4AA batteries, and put battery pack in the control box. Replace the cover firmly.

1. To ensure proper polarity AA Batteries must be used.
2. During initial installation and replacement of Batteries, you must install based on the figure provided above.
3. During long periods of non-use, it is recommended to remove the batteries from the battery pack.

Note: Please check and clean battery contacts prior to installation.
Single use AA Batteries are recommended.

Instructions

Install the bidet onto the toilet.

Operation

1. Press, the high light is on
2. Press again, the low light is on
3. 3rd Press, light is off

Replacing the battery

When the light turns red please replace the battery.

When replacing the battery, press the release button and the bidet, then remove. Repeat the steps above to rep ace the Batteries.

1. To prolong battery life, night light turns off after 7 hours
2. Pressing the power button will reset the 7 hour timer

Cleaning and maintenance

1. Cleaning the exterior of the bidet seat
   Use a smooth sponge/cloth with water and/or mild soap to clean the product. Do not use the following types of cleaning products: hydrogen chloride detergent, paint thinner, benzene abrasive paper, polishing agent, bleach, or chlorine.
   
2. Cleaning the spray nozzles
   Pull out the nozzle softly and use a smooth cloth/sponge or soft toothbrush to clean the nozzle.
   
3. Clean the filter and regulator
   (If the water flow is less than usual)
   
   1. Turn off water supply, remove the white water hose and clean the filter screen.
   2. Clean the regulator o-ring.
4. Remove the main body
   Close the cover. Push and hold the release button and pull the bidet seat forward as shown.
   

Self Diagnosis and Troubleshooting

If any failure still occurs after above troubleshooting, please contact support@Biobidet.com.

Do not disassemble, repair, or remodel the unit, as this will void warranty.

Specifications

Technical Support/Customer Service
Head Office U.S.
7900 S Route 31, Crystal Lake IL 60014

20. 877 339 5214

support@biobidet com

Office in Canada
201-669 Ridley Place, Delta BC V3M6Y9

20. 800.511 6049;
    604 525 5410

support@biobidet.com
www.biobidet.com