Table of Contents
Advertisement
•
Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
•
Press TRSF to store the new passcode.
SET ANSWER MODE
You can receive internal calls in one of three modes (see Answering Intercom
Calls under Intercom Calls for descriptions):
•
While on-hook, press TRSF and then dial 103.
•
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
•
Press TRSF to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have For-
ward No Answer (FNA) turned on, you must answer screened transfers by press-
ing ANS/RLS or the MONITOR key if you are using a 7B phone before your FNA
timer expires or the call will forward.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing CALL
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 001 to turn Automatic Hold on or 000 to turn it off.
•
Press TRSF to store your selection.
NOTE: Intercom calls can only be automatically put on hold by pressing TRSF.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When us-
ing headset mode, press the ANS/RLS or the MONITOR key if you are using a
7B phone to answer and release calls.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 021 to use the headset or 020 to use the handset.
•
Press TRSF to store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this key while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the key while the light
is lit will cause the keyset to return to handset mode and the light will go out.
38
HOT KEYPAD
On the DCS 400si, your keyset's keypad can be made "live" or "hot" so that it is
not necessary to lift the handset or press SPK or the MONITOR key before you
begin dialing. Calls can be made and features activated by simply dialing the
C.O. line number, trunk group access code, intercom number or feature access
code. To activate this feature:
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 031 to turn the Hot Keypad on or 030 to turn it off.
•
Press TRSF to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button on
the dial pad. This tone can be turned on or off.
•
While on-hook, press TRSF and then dial 110.
•
Dial 040 to turn tones off or 041 to turn tones on.
•
Press TRSF to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 051 to turn this feature on or 050 to turn it off.
•
Press TRSF to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or
press the ANS/RLS or the MONITOR key if you are using a 7B phone. This
method will always answer calls in the order they arrived at your keyset. When
you turn ring preference off, you must press the flashing button to answer a call,
allowing you to answer calls in the order you choose.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 061 to turn ring preference on or 060 to turn it off.
•
Press TRSF to store your selection.
39
Advertisement
Table of Contents
