THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Important Safety Instructions Read these instructions. This apparatus has been designed with Class-I construction and must be connected to a mains socket outlet with a protective earthing Keep these instructions. connection (the third grounding prong).
Features .........................................6 Things to Remember ....................................7 About This Guide .......................................7 Getting Started ......................................7 Chapter 2 : Thump210XT Rear Panel Features ...........................8 Power Connector .......................................8 Power Switch......................................8 XLR and 1/4"Combo Input Jacks ................................8 1/8" Input Jack [Ch. 2] .....................................9 Mic / Line Switch [Ch. 1] ..................................9 Gain Knobs [Ch.
Adapt the sound to your space and application with 4 voicing modes and indoor/outdoor settings. You can even link two Thump210XT speakers wirelessly and control both from the Thump Connect 2 app. Lightweight and Built-Like-A-Tank™, Thump210XT is the ultimate compact loudspeaker for mobile PA systems, DJs, bars and more.
This guide is designed to be accessible, with subsections as complete as practical to minimize having to electronically leaf back and forth looking for the whole story. The entire manual does not need to be read to figure out how to use Thump210XT.
Pin 2 = Positive (+ or hot) COLD Pin 3 = Negative (– or cold) SHIELD COLD NEVER connect the output of an amplifier directly to a Thump210XT’s input jack. This could damage the input circuitry and we wouldn’t want that now, would we?
Sleeve = Shield Tip = Hot (+) SLEEVE NEVER connect the output of an amplifier directly to a Thump210XT’s input jack. This could damage the input circuitry and we wouldn’t want that now, would we? 1/8" Input Jack [Ch. 2] This input channel may accept an 1/8"...
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Gain Knobs [Ch. 1 and 2] If you haven’t already, please read the “Quick Start” section on page 7. Setting the gain correctly will ensure that the preamplifier’s gain is not too high, where distortion could occur, and not too low, where the quieter, exquisitely-delicate passages might be lost in background noise.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Main Volume Knob The volume knob adjusts the overall signal level at the input to the built-in power amplifiers. It ranges from Off (– ) to MAX (maximum gain). • Thump loudspeakers are designed to operate with a +10 dBu signal when all knobs are at the center position.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Music Ducking Have you been to an event where music was playing, then when someone spoke into the mic, that the music volume decreased greatly (but was still there)? That’s called “music ducking”! When the music ducking switch is engaged, the channel 2 level will decrease when a mic signal is present on channel 1.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER HVAC Like their counterpart loudspeakers – the appropriately named Thump212XT and Thump215XT – the Thump210XT is also blessed with an excellent “HVAC” system. Read below for more information! MIST ON / OFF SPEED...
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER E. Heat Level If the temperature is the aforementioned “frigid”, we’re pretty confident that you’re going to want to crank the heat... perhaps not, but we’d bet on it! This works similarly to that of the fan speed with settings ranging from 1 (low heat) to 5 (cranked heat). Quickly press this button to what setting you would like, up to five times.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER The Bluetooth connection may disconnect when affected by electrostatic discharge (ESD) or electrical fast transients (EFT). If this occurs, manually reconnect the Bluetooth connection. As mentioned earlier, a Bluetooth connection may be used simultaneously with the combo jacks – XLR or 1/4"...
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Final Thoughts Just a few final thoughts before we dive into a little more boring “techy”-type stuff. For starters, we would like to remind you once again that ThumpXT works great on its own, but when paired and connected with a device using the Thump...
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Chapter 3 : Protection Circuitry Introduction ThumpXT loudspeakers employ a built-in limiter for less distortion at peak levels. A dynamic bass response circuit provides optimal low frequency response regardless of overall output level. Additional protection includes automatic thermal shutdown should the amp overheat.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER AC Power Be sure the ThumpXT loudspeaker is plugged into an outlet that is able to supply the correct voltage. It will continue to operate at lower voltages, but will not reach full power. Be sure the electrical service can supply enough amperage for all the components connected to it.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Chapter 4 : Placement Introduction WARNING: Installation should only be done by an experienced technician. Improper installation may result in damage to the equipment, injury or death. Make sure that the loudspeaker is installed in a stable and secure way in order to avoid any conditions that may be dangerous for persons or structures.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Room Acoustics ThumpXT loudspeakers are designed to sound fantastic in nearly every application. But, room acoustics play a crucial role in the overall performance of a sound system. However, the wide high-frequency dispersion of the ThumpXT loudspeakers helps to minimize the problems that typically arise.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Chapter 5 : Rigging Introduction WARNING: Installation should only be done by an experienced technician. Improper installation may result in damage to the equipment, injury or death. Make sure that the loudspeaker is installed in a stable and secure way in order to avoid any conditions that may be dangerous for persons or structures.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Rigging Hardware and Accessories Rigging our loudspeakers will invariably require hardware not supplied by us. Various types of load-rated hardware are available from a variety of third-party sources. There are a number of such companies specializing in manufacturing hardware for designing and installing rigging systems.
Bring your favorite axe and mic, ThumpXT loudspeakers and cables and power cords. In this example, a Mackie EM-89D microphone is connected to the channel 1 input of a ThumpXT loudspeaker, used as the main PA. The Channel 1 gain knob should be set to Mic. The Mic/Line switch should be ENGAGED [Mic], as well.
THUMP210XT 10" 1400W ENHANCED COMPACT POWERED LOUDSPEAKER Hookup Diagrams > Small Club System In this example, a ProFX12v3+ mixer is connected directly to two Thump210XT loudspeakers. MUSIC MUSIC LIVE LIVE CLUB CLUB SIG/OL SIG/OL It is the perfect setup for a small club or...
The L/R outputs of the DJ controller are connected to the “A” inputs of two Thump118S subwoofers. The High-Pass Out of each subwoofer is then connected to the input of each Thump210XT loudspeaker. Additionally, a set of Mackie MC-350 headphones is connected to the phones jack of the DJ controller.
From here, the High Pass Out of the two outer Thump118S subwoofers are connected directly to the inputs of a set of Thump210XT loudspeakers. Then set the subwoofer’s High Pass Mode to Deep and the voicing mode of both loudspeakers to live or club. Talk about beefy low end! Outputs 1 and 2 from the mixer may be used as aux sends;...
Troubleshooting If you think your Mackie product has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (www.mackie.com) to get some ideas or contact our technical support heroes.
For warranty service, refer to the warranty information on page 35. Non-warranty service for Mackie products is available at a factory-authorized service center. To locate the nearest service center, visit www.mackie.com, click “Support” and select “Service Center Locater”. Service for Mackie products living outside the United States can be obtained through local dealers or distributors.
You will need it to obtain any warranty service. For full terms and conditions, as well as the specific duration of the Warranty for this product, please visit www.mackie.com/warranty. The Product Warranty, together with your invoice or receipt, and the terms and conditions located at www.mackie.com/warranty constitutes the entire agreement, and supersedes any and all prior agreements between LOUD and Customer related to the subject matter hereof.
Need help?
Do you have a question about the THUMP210XT and is the answer not in the manual?
Questions and answers