Important: Prior to using your KickAss Inverter, it is essential that you thoroughly read and understand the entire User Manual. Any misuse of the product may result in damage to the unit and/or cause harm or serious injury to the user.
Page 3
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DEATH OR SERIOUS INJURY Ÿ WARNING: ELECTRICAL SHOCK HAZARD - Do not dismantle the inverter as it contains hazardous voltages internally. Any attempt to service internal components will void the warranty and could lead to fatal injuries. Ÿ...
Page 4
Ÿ Voltage alarm functionality Ÿ 1x AC output, 1x USB charging port Ÿ Optimal remote control display for easy monitoring and control KAPSWI2000 Ÿ RCD (Residual Current Device) protection Ÿ ATS (Automatic Transfer Switch) Ÿ Maximum efficiency of 94% Ÿ...
SPECIFICATIONS Specification KAPSWI2000 KAPSWI3000 Output Waveform Pure Sine Wave <5% Pure Sine Wave <5% Input Voltage 12V DC (10~16V) 12V DC (10~16V) Output Voltage 240V AC ±5% 240V AC ±5% Output Rated Power 2000W 3000W Surge Power 10 sec 2000W~2400W...
FRONT PANEL KAPSWI2000 A. AC Output Receptacle Standard 10A 240V AC Australia / New Zealand receptacle. For connecting 240V AC appliances to the inverter. B. Main Switch The main switch controls the output of the inverter, allowing you to turn it ON or OFF.
Page 7
D. Fault LED Indicator The Fault LED Indicator will either glow or flash red when a fault is detected, and it will automatically turn off the 240V AC output. Refer to the troubleshooting section for further guidance. E. 5V USB Socket The USB Socket is designated for charging or powering 5V USB devices, such as mobile phones.
Page 8
KAPSWI3000 A. AC Output Receptacle Standard 10A 240V AC Australia / New Zealand receptacle. For connecting 240V AC appliances to the inverter. B. Main Switch The main switch controls the output of the inverter, allowing you to turn it ON or OFF.
Page 9
D. Fault LED Indicator The Fault LED Indicator will either glow or flash red when a fault is detected, and it will automatically turn off the 240V AC output. Refer to the troubleshooting section for further guidance. E. 5V USB Socket The USB Socket is designated for charging or powering 5V USB devices, such as mobile phones.
REAR PANEL KAPSWI2000 A. Cooling Fan The cooling fan(s) integrated into the inverter operate based on temperature and/or load conditions. These fan(s) will activate automatically when the AC load reaches 20% or higher, or if the internal temperature surpasses 45°C.
Page 11
KAPSWI3000 A. Cooling Fan The cooling fan(s) integrated into the inverter operate based on temperature and/or load conditions. These fan(s) will activate automatically when the AC load reaches 20% or higher, or if the internal temperature surpasses 45°C. B. DC Input Terminals Warning: Be careful when connecting the DC input, ensuring correct polarity.
Page 12
REMOTE CONTROL DISPLAY (RCD) SOLD SEPERATELY REMOTE CONTROL DISPLAY INVERTER MODE(1000W/2000W/3000W) Remote Control 100% 0000 131 240 BATT LOAD Inverter AC OUT A) Battery Indication B) Battery Voltage C) AC Output Running D) Power Consumption E) AC Output Voltage F) Inverter Operating...
Page 13
REMOTE CONTROL DISPLAY AUTO TRANSFER MODE(1000W/2000W/3000W) Remote Control 0000 131 240 BATT BYPASS AC OUT AC IN A) Battery Indication B) Battery Voltage C) AC Output Running D) Power Consumption E) AC Output Voltage F) Mains Connected (transfer switch / by-pass) DISPLAY OF PROTECTION FUNCTION ---ERROR CODE Low voltage protection Over voltage protection...
Page 14
CONNECTING THE REMOTE CONTROL To set up the remote control, simply connect it to the inverter using the provided communications cable. This cable, a 6-conductor RJ11 type, is included with the remote control purchase. Ensure the cable is connected to the corresponding RJ- 11 ports located at the rear of the remote and on the front panel of the inverter (referred to as Port F in Figures 1 and 2), noting that the connector follows a Straight Pinout configuration, not a Reverse one.
Page 15
WARNING: ELECTRICAL SHOCK HAZARD For your safety, KickAss Products strongly advises hiring a certified technician or licensed electrician to handle all wiring and installation tasks. This ensures compliance with relevant electrical wiring regulations and installation codes. Failure to adhere to these guidelines may lead to unit damage, as well as potential death or serious injury.
Page 16
Earthing POINT In-Built Earthing Point It is important to install a grounding wire from the unit's inbuilt earthing point to your chassis or a grounding pole. A grounding wire gives an appliance or electrical device a safe way to discharge excess electricity. By taking the electricity that builds up during a malfunction or surge and sending it outside of your circuit, into the ground.
CONNECTING THE INVERTER To properly connect the inverter, follow these steps: 1. Ensure both the main and remote main switches (if applicable) are in the OFF position. 2. Begin by attaching one end of the positive DC input cable to the inverter's positive DC input terminal.
OPERATING THE INVERTER To operate the inverter: 1. Ensure the connected AC appliance is switched OFF before powering up the inverter. 2. Activate the inverter by switching the Main Switch to the ON position. 3. Wait for the Power LED Indicator to illuminate, then proceed to switch ON the connected AC appliance.
3. Test the AC appliance on your home's 240V is faulty. AC wall socket. 4. Turn on the AC appliance. 5. If there is still no output, contact KickAss. The inverter beeps Low DC input 1. Check that the battery is not flat and is fully twice voltage warning.
Page 20
45°C). If the cooling fans will shut down. are not functioning, the inverter will need further assessment, please contact KickAss. 2. If the fan is functioning, check that all ventilation slots and fan openings are not obstructed. Also ensure that adequate cool air...
In the unlikely event of a technical issue, please reach out to our online warranty page before returning the inverter. If a unit is returned within the warranty period, KickAss Products will either repair or, at its discretion, replace it free of charge. Repairs may involve the use of new or reconditioned replacement parts, determined by the manufacturer.
Page 22
Kickass is a registered trademark of Kickass Products Pty Ltd Designed & imported by Kickass Products Pty Ltd 39 Iris Place, Acacia Ridge, QLD 4110 Australia Made in China...
Need help?
Do you have a question about the KAPSWI2000 and is the answer not in the manual?
Questions and answers