Subscribe to Our Youtube Channel
Related Manuals for KickAss KAI700WPD
Summary of Contents for KickAss KAI700WPD
- Page 1 PURE SINE WA VE DIGITAL INVERTER USER MANUAL K A I 7 0 0 W P D | K A I 1 2 0 0 W P D | K A I 2 0 0 0 W P D | K A I 3 0 0 0 W P D V1.2...
-
Page 2: Important Safety Information
1. INTRODUCTION Thank you for purchasing a KickAss Pure Sine Wave Digital Inverter. This unit converts 12V DC to 240V AC using intelligent electronics, so you can operate and run mains powered devices from a suitable sized 12V battery. As inverters output hazardous voltages, please ensure all instructions are read carefully before use. -
Page 3: Dimensions And Specifications
• Protection features including, low voltage alarm, overload shutdown, short circuit, input overvoltage and over temperature 4. DIMENSIONS AND SPECIFICATIONS 270,6 261,8 78,6 284,1 700W Pure Sine Wave Inverter KAI700WPD KAI700WPD DC Volt 10-15V DC Input Voltage Range ≦1A No-Load Current Convert Efficiency ≧90%... - Page 4 362,3 113,3 340,3 15,2 1200W Pure Sine Wave Inverter KAI1200WPD KAI1200WPD DC Volt 10-15V DC Input Voltage Range ≦1A No-Load Current ≧90% Convert Efficiency DC Wiring 16mm² Output Voltage 240V AC 50/60Hz±0.5Hz Rated Power 1200W Peak Power 2400W 5V 2.1A Waveform Pure Sine Wave Remote Cord Length...
-
Page 5: Installation
KAI3000WPD DC Volt 10-15V DC Input Voltage Range ≦1A No-Load Current Convert Efficiency ≧90% DC Wiring 35mm² Output Voltage 240V AC 50/60Hz±0.5Hz Rated Power 3000W Peak Power 6000W 5V 2.1A Waveform Pure Sine Wave Remote Cord Length 245,0 3000W Pure Sine Wave Inverter KAI3000WPD 5. -
Page 6: Remote Display
Wiring the batteries in parallel increases the total run time the batteries can operate the AC loads. A parallel connection combines overall battery capacity by the number of batteries in the string. In the example shown, four 12 VDC/100AH batteries are combined into a single 12VDC/400AH battery bank. -
Page 7: Operation
6. OPERATION 6-1 Operation - General Once your inverter is installed and connected to batteries, switch the inverter on using the main power switch. Your inverter will now be ready to use, simply plug in an appliance and operate. The digital LCD control can be used as detailed below. - Page 8 6-4 Setting Inverter Parameters: BATT 100% 1. Press "SET/OK" for 5s. You are now entering the settings interface. As shown above. 2. Press "UP and DOWN" to adjust parameters. 3. Press "SET/OK" to confirm adjustment. 4. To reset the parameters press "set" and the ICON 1 will flash. 5.
-
Page 9: Troubleshooting
7. TROUBLE SHOOTING BATT OUTPUT ERROR 100% Warning Do not open or disassemble the inverter. Attempting to service the unit yourself may result in a risk of electrical shock or fire. When faults occur: The icon indicates the corresponding fault code and flashes for attention ERROR Fault Code... - Page 10 Warranty does not cover products that have not been used in accordance with the KickAss® user guide or are outside the warranty terms and conditions. QUESTIONS AND COMMENTS Please visit us at supportportal.kickassproducts.com.au...
Need help?
Do you have a question about the KAI700WPD and is the answer not in the manual?
Questions and answers