12v to 240v inverter pure sine wave range (23 pages)
Summary of Contents for KickAss KAI500WPD
Page 1
PURE SINE WA VE DIGITAL INVERTER USER MANUAL K A I 5 0 0 W P D | K A I 7 0 0 W P D | K A I 1 2 0 0 W P D | K A I 2 0 0 0 W P D | K A I 3 0 0 0 W P D...
1. INTRODUCTION Thank you for purchasing a KickAss Pure Sine Wave Digital Inverter. This unit converts 12V DC to 240V AC using intelligent electronics, so you can operate and run mains powered devices from a suitable sized 12V battery. As inverters output hazardous voltages, please ensure all instructions are read carefully before use.
• Protection features including, low voltage alarm, overload shutdown, short circuit, input overvoltage and over temperature 4. Dimensions and Specifications 270,6 261,8 78,6 284,1 Pure Sine Wave Inverter500W/700W KAI500WPD | KAI700WPD KAI500WPD KAI700WPD DC Volt DC Volt 10-15V DC 10-15V DC Input Voltage Range Input Voltage Range ≦1A...
Page 4
362,3 113,3 340,3 15,2 Pure Sine Wave Inverter1200W KAI1200WPD KAI1200WPD DC Volt Input Voltage Range 10-15V DC ≦1A No-Load Current Convert Efficiency ≧90% Fuse 50amp blade fuse x2 DC Wiring BVR16*1 Output Voltage 240V AC 50/60Hz±0.5Hz Rated Power 1200W Peak Power 2400W 5V 2.1A Waveform...
482,3 113,3 460,3 15,2 Pure Sine Wave Inverter3000W KAI3000WPD KAI3000WPD DC Volt 10-15V DC Input Voltage Range ≦1A No-Load Current Convert Efficiency ≧90% Fuse 40A*12 DC Wiring RVV35*1 Output Voltage 240V AC 50/60Hz±0.5Hz Rated Power 3000W Peak Power 6000W 5V 2.1A Waveform Pure Sine Wave Remote Cord Length...
5.2 Wiring Follow this procedure to connect the battery cables to the DC input terminals of the inverter. Your cables should be as short as possible (ideally use the included cables) enough to handle the required current in accordance with the electrical codes or regulations. If cables are not an adequate gauge or length this will decrease the inverters performance such as poor surge capabilities, low input voltage warnings and shutdowns.
6. OPERATION 6-1 Operation - General Once your inverter is installed and connected to batteries, switch the inverter on using the main power switch. Your inverter will now be ready to use, simply plug in an appliance and operate. The digital LCD control can be used as detailed below.
Page 8
6-4 Setting Inverter Parameters: BATT 100% 1. Press "SET/OK" for 5s. You are now entering the settings interface. As shown above. 2. Press "UP and DOWN" to adjust parameters. 3. Press "SET/OK" to confirm adjustment. 4. To reset the parameters press "set" and the ICON 1 will flash. 5.
7. TROUBLE SHOOTING BATT OUTPUT ERROR 100% Warning Do not open or disassemble the inverter. Attempting to service the unit yourself may result in a risk of electrical shock or fire. When faults occur: The icon indicates the corresponding fault code and flashes for attention ERROR Fault Code...
Page 10
THANK YOU FOR CHOOSING KickAss® is committed to providing you with the most up to date product information. As printed material is harder to update we have created an online user guide portal including videos, user guides and product tips so you can view or download the latest product information at any time.
Warranty does not cover products that have not been used in accordance with the KickAss® user guide or are outside the warranty terms and conditions. QUESTIONS AND COMMENTS Please visit us at kickass.com.au or...
Need help?
Do you have a question about the KAI500WPD and is the answer not in the manual?
Questions and answers