Related Manuals for Super DSB1S
Summary of Contents for Super DSB1S
- Page 1 Balance for Drum Lift Clamp DSB1S Operation Manual This operation manual explains the basic operation and handling of the clamps. Please read this manual carefully before use and observe the precautions for safe operation. SUPER TOOL CO., LTD.
- Page 3 brand lifting clamps are energy-saving lifting equipment which have been developed for the purpose of transporting steel materials. Proper use Operate lifting clamps after carefully reading and understanding this instruction manual for enhancing efficiency and safety of operation. Prime efficiency and economy Advanced functions, reasonableness and versatile applications of finely and carefully designed lifting clamps ensure...
- Page 4 Precautions for safety operation (Pages 1〜10 are common to all lifting clamp models) Be sure to read this instruction manual carefully before use. Mistaken use of lifting clamp may cause a danger such as dropping of load. Education of “crane safety regulations,” “operation manual for lifting clamp,”...
-
Page 5: Check Before Operation
1. Handling in general WARNING ● Do not operate until the contents of the operation manual, and caution tag/plate are thoroughly read and understood. ● Do not operate without a legal qualification. ● Be sure to clear of the area of the operation for lifting or turning a load against possible drop off or fall over. -
Page 6: Lifting Operation
3. Lifting operation WARNING ● Do not use clamp, lifting at one point. (excluding special or custom ordered products) ● Do not use the clamp in the following ways of lifting: lifting of two or more individual objects at one time. (overlapped loads, padded load etc. - Page 7 ● Stop the lifting operation by crane for a moment when the load is applied to the lifting ring for safety checking. (depth of the load into the clamp opening; status of locking). ● Stop the operation of the crane just before the load reaches the ground, and check the following matters: (Inclination or Instructed falling over of the load and security around the landing area...
- Page 8 General warning for use ■ (common to all lifting clamp models) Be sure to select proper model clamps for use. Pay special attentions to keep the lifting direction (rope angle). Confirm the weight of the load. Do not exceed maximum capacity (designated ton) on clamps.
- Page 9 Never lift two or more steel plates or steel members at a time. The load may move to an unexpected direction when lifted off the ground and as such confirm the center of gravity and the clamping posi- tion for safety when raising. Sufficient caution should be taken until the clamp with the load becomes completely balanced.
-
Page 10: Maintenance And Inspection
■ Maintenance and Inspection 1. Maintenance Daily maintenance is important for efficient and safe operation even under the severe use condition and for such purposes, please comply with the followings. (1) Designate the use standards and control. (2) Keep clamps indoor and do not leave them outdoor. (3) Check the followings to maintain in a good condition. - Page 11 (2) Standards on periodic inspection (A) Establishing dates of periodic inspection. (B) Establishing inspection and maintenance methods. (a) Inspecting period. (b) Person in charge of the inspection. (c) Inspection site. (d) Tools and devices for inspection. (e) Establishment of permissible limit of use. ( f ) Explicit designation of maintenance and repair methods.
- Page 12 Lifting angle and rated load of wire rope The maximum rated capacity of wire ropes also differs according to the lifting angle. Therefore, after paying attention to the lifting angle, always use wire ropes with the appropriate diameter. Correlation table between the lifting angle and the applicable load for wire rope (for 2-point lifting) ■ ■ JIS G 3525 6×24 A type W rated load (for 1 single rope) D wire rope diameter Safety factor Ｓ ＝6 (Change in % of the lifting capacity rate according to the lifting angle) 100% Maximum allowable load (rated load) for 2 wire ropes (ton) （mm） （ton） 6 0.30 0.60 0.57 0.51 8 0.53 1.07 1.03 0.92 ...
- Page 13 Balance for Drum Lift Clamp DSB1S Operation Manual and Inspection Standards...
-
Page 15: Specifications
Balance for Drum Lift Clamp DSB1S ■Uses This balance is specially designed for drum lift clamp. ■Specifications Rated Capacity Net Weight Lifting Pitch Item No. (ton) (kg) (mm) DSB1S 615， 445 ■Main Dimensions and Replacement Parts W L L . 1 T O N N O . - Page 16 ■ INSPECTION STANDARDS FOR DSB1S Item Inspection method Limit of use Main causes Remedy Visually check or Impossible lifting When the deformation measure to find exceeds 6mm. angle deformation. Sudden shock load More than 6mm deformation Overload Natural wear More than 6mm deformation...
- Page 18 24． 9...
Need help?
Do you have a question about the DSB1S and is the answer not in the manual?
Questions and answers