MELICONI Easytel 2 Booklet
  1. Manuals
  2. Brands
  3. MELICONI Manuals
  4. Remote Control
  5. Easytel 2
  6. Booklet
MELICONI Easytel 2 Booklet

MELICONI Easytel 2 Booklet

Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

Thank you for choosing a Meliconi remote control.
The Easytel 2 remote control is designed to command a TV and a DECODER (satellite or digital terrestrial).
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the
continuously until the button is released. If the light is off or blinks, the inserted batteries are low,
therefore they need replacement.
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
As the remote control is capable of controlling 2 devices, during setup (and also during normal use), you must select the
operation mode; then define which device you want to control. (TV / STB)
To select the operation mode, press the
the device you want to operate is switched on. (TV =
Before using the remote control, for each device you wish to control, it is essential to set a specific code, it matched.
Identify the specific code and set it into the remote control using one of the following ways:
Keep this booklet for future reference
SAFETY WARNINGS
INSERTING THE BATTERIES
5
button and check that the LED remains on
SELECTION OF OPERATING MODE
WARNING:
button quickly and repeatedly until the LED corresponding to
red
ACTIVATION OF REMOTE CONTROL
SMARTPHONE
TABLET - WEB
Easytel 2
led / STB =
green
led)
MANUAL
SEARCH

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Easytel 2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MELICONI Easytel 2

Summary of Contents for MELICONI Easytel 2

  • Page 1 Keep this booklet for future reference The Easytel 2 remote control is designed to command a TV and a DECODER (satellite or digital terrestrial). The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.

  • Page 2: Manual Search

    • Three final flashes indicate that the operation has been completed successfully. VERIFY Check that the MELICONI remote control operates your device in the main functions; if it does not, REPEAT the procedure. NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains off.

  • Page 3: Buttons And Functions

    The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it. Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.

  • Page 4: Child Mode

    COMBINED KEYPAD the video Using the MELICONI remote control to command 2 devices (TV and DECODER) it is often necessary to select the operating mode before to operate on the corresponding device. To avoid this uncomfortable and frequent operation, it is possible to combine in a single keyboard two different modes of use.

  • Page 5: Troubleshooting (Faq)

    If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code as described in the ACTIVATION OF REMOTE CONTROL chapter. Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad. To enable them, operate as described in the BUTTON AND FUNCTIONS chapter.
  • Page 6 The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must be collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type.

Table of Contents