Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FujiFilm BM-8753BFR-F
Summary of Contents for FujiFilm BM-8753BFR-F
- Page 1 FUJIFILM Corporation BM-8753BFR-F User Manual BT Module User manual Version 1.0 © AII rights reserved. AII trade names are registered trademarks of respective manufacturers listed. This manual may not be copied in any media or form without the written consent of original maker.
- Page 2 User Manual BM-8753BFR-F 1. Certification mark------------------------------------------------------Page.2 2. Specifications------------------------------------------------------------Page.3-15 3. warning statement-----------------------------------------------------Page.16-19 ※本製品を搭載する際に各ビンの説明書をご参照ください。(Page.5-7) ※ Please refer to the manual of each pin when installing this product. 2/19...
- Page 3 User Manual BM-8753BFR-F BT Module Description transmission compliant with H4 speci- The BM-8753BFR-F is a highly integrated fication single-chip Bluetooth 2.1/3.0/4.0/5.1 Integrated MCU to execute Bluetooth module with a UART interface. It combines protocol stack a BT Protocol Stack (LM, LL, L2CAP, GATT, Supports all packet types in basic rate ...
-
Page 4: Revision History
User Manual BM-8753BFR-F Revision History Version Date Change Description 12/02/2022 Initial release 12/09/2022 Addition Pin Definition 05/12/2023 Change dimension tolerance to +- 0.15mm 1. Change transmitter power to 7.5dBm 06/12/2023 2. Addition recommend layout footprint Note： All electrical and mechanical specifications may be changed by CC&C Technologies, Inc. -
Page 5: Factory Options
User Manual BM-8753BFR-F Factory options RF output by PCB Antenna(RF type-1) 5/19... -
Page 6: Functional Block Diagram
User Manual BM-8753BFR-F Functional Block Diagram GPIOs BT Module UART 3.3V Block Diagram 6/19... -
Page 7: Pin Assignment (Top View)
User Manual BM-8753BFR-F Pin Assignment (Top view) 7/19... -
Page 8: Pin Definition
User Manual BM-8753BFR-F Pin Definition Pin Name Pad Type Description RF output external Antenna (Type 2) Ground Programmable GPIO P1_0 IO PU Configurable pull high/low state LDO_HV33 power domain Programmable GPIO P1_1 IO PU Configurable pull high/low state ... - Page 9 User Manual BM-8753BFR-F Configurable pull high/low state LDO_AUX power domain Programmable GPIO Programmable as ADC input pin P0_0/ADC_0 IO A Configurable pull high/low state LDO_AUX power domain Programmable GPIO Programmable as ADC input pin...
-
Page 10: Specification
User Manual BM-8753BFR-F SPECIFICATION Product Name BT Module Model Number BM-8753BFR-F Operating Frequency 2402~2480 MHz Transmitter power 7.5dBm Receiver sensitivity ≦-70dBm Power Voltage Range Symbol Description Min. Typ. Max. Units VD33 3.3V Supply Voltage 4.35 Operating Temperature Digital logic characteristics Item Min. -
Page 11: Module Dimension
User Manual BM-8753BFR-F Module dimension 11/19... - Page 12 User Manual BM-8753BFR-F Recommend layout footprint 12/19...
- Page 13 User Manual BM-8753BFR-F Placement Guideline It is recommended that module be placed on the corner of the main board or near the edge as shown below. On the corner Near the edge 13/19...
- Page 14 User Manual BM-8753BFR-F 50 Ohm Feed Line: H1: 30 ~ 60 mil Er1: 4.2 W1: 20 mil W2: 20 mil D1: 5 C1: 0.7 mil C2: 0.7 mil T1: 1.4 mil (1 oz) Impedance: 51 ~ 53 Ohm Reference – Temperature Reflow Chart Reflow Notice: 1.
- Page 15 User Manual BM-8753BFR-F C per second. 4. This temperature reflow chart is for reference only, it depends on the manufacturing machine’s characters requirement. This module is surface mount device; please refer below conditions for drying before solder reflow processes. (extracted from IPC/JEDEC J-STD-033B.1)
- Page 16 User Manual BM-8753BFR-F Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 17 User Manual BM-8753BFR-F This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional com- pliance requirements required with this module installed.
-
Page 18: Important Note
User Manual BM-8753BFR-F Canada - Innovation, Science and Economic Development (ISED) This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must ac- cept any interference received, including interference that may cause undesired operation. -
Page 19: Note Importante
User Manual BM-8753BFR-F co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
Need help?
Do you have a question about the BM-8753BFR-F and is the answer not in the manual?
Questions and answers