Electron E-COAT+3 MASTER Series User Manual
  1. Manuals
  2. Brands
  3. Electron Manuals
  4. Paint Sprayer
  5. E-COAT+3 MASTER Series
  6. User manual

Electron E-COAT+3 MASTER Series User Manual

Powder coating equipment
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
POWDER COATING EQUIPMENT USER'S MANUAL
E-COAT+3 MASTER
SER I ES
Check our
product
electron.com.tr + info@electron.com.tr
online

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E-COAT+3 MASTER Series and is the answer not in the manual?

Questions and answers

john sparrow
April 28, 2025

MY MACHINE WILL NOT POWER UP

0
1 comments:
Mr. Anderson
May 15, 2025

The Electron E-COAT+3 MASTER Series machine may not power up due to one or more of the following reasons:

1. Low Backup Battery: The backup battery on the board may be low (E16 LOW BATT). Replace the battery.

2. EEPROM Error: An EEPROM error (E17) may prevent startup. Contact support for EEPROM error handling.

3. Poor Grounding: Improper or weak grounding of the device or its components can cause startup failure. Ensure proper earthing of the chassis and components. Grounding resistance should be a maximum of 1 MOhm.

4. Communication Errors: If the gun, gun cable, or cascade is defective or disconnected, the system may not detect the gun (E3 NO GUN DETECTED) and will prevent oscillation output.

5. Defective Components: A defective cascade or open-circuited gun cable may stop the system from initializing correctly.

All grounding and hardware connections should be checked carefully.

This answer is automatically generated

0
Jeffrey Copeland
July 17, 2025

I keep getting the e3 error code. What should I look for or change? Im using a manual gun/method.

0

Subscribe to Our Youtube Channel

Related Manuals for Electron E-COAT+3 MASTER Series

Summary of Contents for Electron E-COAT+3 MASTER Series

  • Page 1 POWDER COATING EQUIPMENT USER’S MANUAL E-COAT+3 MASTER SER I ES Check our product electron.com.tr + info@electron.com.tr online...
  • Page 2 © 2023 Sistem Teknik Makina A.Ş. All rights reserved. 10010 St. No:10 35470 ITOB Menderes Izmir TURKEY No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Sistem Teknik Makina San. Ve Tic. A.Ş. Under the law, reproducing includes translating...

  • Page 3: Table Of Contents

    4-2 Injector Structure and Power Coat Transfer Principle..............................33 5- Powder and Mixture Value Tables ......................5-1 E-FEED+3 INJ General Usage Value ..................................34 5-2 Use of E-COAT+3 Series Devices with E-FEED+3 INJ............................34 5-2-2 Use with E-COAT+3 Master Series Control Units ...........................35...
  • Page 4 6- Cleaning and Mainteace........................6-1 Cleaning of Injector....................................6-2 Cleaning Module..............................37 6-3 Filter Module...............................37 6-4 Teflon Bushing Module............................38 6-5 Injector Nozzle Assembly Module..........................39 7- -GUN+3 C1 General Information..................7-1 Field of Application............................40 7-2 Technical Data..............................7-3 Design and Functions...............................42 7-4 Lighting Function..............................

  • Page 5: Safety Regulations

    Safety Regulations This section sets out the fundamental safety regulations that must be followed by the user and third parties using the E-COAT+3 Master These safety regulations must be read and understood before the E-COAT+3 Master is used. 1.1. Safety Symbols The following warnings with their meanings can be found in the Sistem Teknik Makina operating instructions.

  • Page 6: Technical Safety Regulations For Stationary Electrostatic Powder Spraying Equipment

    Technical Safety Regulations for Stationary Electrostatic Powder Spraying Equipment 1.3.1. General Information The powder spraying equipment of Sistem Teknik Makina (Electron) is designed for safe use and to the latest technological specs. Electrostatic powder equipment could create dangerous situations unless it’s used properly. In addition to that, there might be a danger to life and limb of the user or third party, a danger of damage to the equipment and other machinery that belongs to the user and hazards to the proper operation of equipment.

  • Page 7: Special Type Of Hazards

    1.3.4. Special Types of Hazard Power : All the high voltage equipment should be unplugged before opened. This is a huge life risk thus it has to be taken under great care. Powder: Powder/air mixtures could be ignited by sparks. Sufficient ventilation is a must while using powder spraying equipment.

  • Page 8: Product Specific Safety

    EN European Standarts 2014/34/EU The approximation of the laws of the Member States relating to apparatus and safety systems for their intended use in potentially explosive atmospheres EN 12100-1 EN 12100-2 Machine safety EN IEC 60079-0 Electrical equipment for locations where there is danger of explosion EN 50050-2 Electrical apparatus for potentially explosive atmos- pheres - electro- static hand-held spraying equipment...

  • Page 9: Conformity Between Products

    E-COAT+3 Mobile Trolley w/Box Holder and Suction • Tube Hose connection accessories • 1.6. Conformity Between Products Electron E-COAT+3 Master can be used Electron E-GUN+3 C1 can be used with: Electron E-GUN+3 C3 can be used with: with: • E-COAT+3 Master •...

  • Page 10: 2- Technical Data

    Technical Data 2.1. Electrical Data E-COAT+3 Master Control Unit Nominal Input Voltage 100-240 VAC Operating Frequency 50-60 Hz Input Power 60 VA Gun Nominal Output Voltage Max. 20 Vp-p Gun Nominal Output Current Max. 1,5 A Auxiliary Output Type 24 VDC/max. 10W, 100-240 VAC/max.100W Purge Output Type 24 VDC, max.

  • Page 11: General View

    2.6. Nozzle Air Front Panel Display and Control Buttons Casing Back Panel and I/O 2.7. Front Panel and Input Buttons Button Definition Fluidization and Vibration Motor(Only Multicolor) & Autostart Active/Passive Button Menu Button Bluetooth Activation Button Power On Button Power Off Button Recipe Button 1 Recipe Button 2 Recipe Button 3...

  • Page 12: Back Panel And Connections

    2.8. Back Panel and Connections Back Panel Connections Connection Function 1.0 POWER IN MAIN POWER CONNECTION (100-240VAC, 50-60Hz) Glass Fuse Holder 1.6A 1.6A 1.2 Fuse User Datagram Protocol 1.3 UDP/IP (Optional) 1.4 Gun Gun Cable Connection Fluidization Unit/Multicolor Unit Connection 1.5 AUX 1.6 PURGE (Optional) Purge Valve Connection (Supplied with optional Purge Module)

  • Page 13: General Information

    2.8.1 E-COAT+3 Master Mobile Trolley Control Unit Rotation The control units in the mobile trolley can rotate max. 55 degrees to the right and left to provide ergonomic and practical use. The fixing knob at the back of the trolley is used to rotate the device heads.

  • Page 14: General Instructions

    2.9. General Instructions Usage Types a. Automated Recipe Working Mode This type of usage allows the customer to work with custom made recipes as well the three predefined recipes stated below: Coating on Straight Faced Materials Coating on Coated Materials Coating on Notched Surfaces Boost Mode Predefined Recipe Buttons...
  • Page 15 User Defined Recipe Working Mode In this working principle, the user can save their own working parameters and change them. There can be 50 recipes starting from P01 to P50, four of which P01-02-03-04 are factory predefined recipes. These predefined recipes are explained in this manual.
  • Page 16 e.Consumable Counters E-COAT+3 Master is designed with consumable counters so that the use would be always aware of the materials. You can open the counter via pressing the B2 button for two times. The user can also adjust the counters to create a warning when the consumables are about to finish or when they are finished.
  • Page 17 g.Micro Charge Feedback Micro Charge Feedback When coating simple components with some complex geometries, the control unit setting can be set below 10 microamps to prevent overcoating. In this state, the control unit automatically switches to precise MCF (Mictro Charge Feedback) mode. With this mode, the control unit takes more current samples and the charge loaded on the paint can be controlled at the micro level and precise coating process can be performed.

  • Page 18: 3- Start Up

    Start Up 3.1. Grounding...
  • Page 19 16mm GROUNDING CABLE SURFACE GROUND 4mm GROUNDING Q20mm, 1,5m. CABLE COPPER GROUND ELECTRODE All electricity conducting parts and machinery in the workplace must be earthed. Please connect a ground wire 1.5 meters before the entrance of the cabinet, in the middle of the cabinet and 1.5 meters after the exit of the cabinet.

  • Page 20: Installation

    3.2. Installation a. “Bare” and “H” type Device Kits Electro-Pneumatical Connections...
  • Page 21 b. Double “Bare” and “H” type Device Kits Electro-Pneumatical Connections...
  • Page 22 c.“M” type Device Kits Electro-Pneumatical Connections...
  • Page 23 d. Double “M” type Device Kits Electro-Pneumatical Connections...
  • Page 24 e.“A”type Device Kits Electro-Pneumatical Connections...

  • Page 25: Set Up

    3.3. Set Up Info: E-COAT+3 Master Powder Coating Control unit always starts with the last used configuration prefer- ences. In the above “System Connections” all the electrical and pneumatic connections are shown. After correctly connecting the device, the user can press the “Main Switch” to start the control unit. The below procedure should be done at the first Start E-COAT+3 Master should be calibrated according to the products that are going to be powder coated before the start up.

  • Page 26: Operation

    3.4. Operation a. Creating and Saving a User Recipe Recipe Segment After adjusting the values from the control unit, the user can save the recipe for future usage. To save the current recipe, press and hold the B15 segment button for 2 seconds. You will see the recipe number flashing every 500ms. The user then chooses the recipe number for the current or new recipe.
  • Page 27 Predefined Recipe Working Parameters are located below Predifined Recipe Name High Voltage (kV) Current (µA) Flat Surface Application Coating on Coating Application Notched Surface Application Boost Mode c. High Voltage Preferences: There are two different methods in E-COAT+3 Master to change the High Voltage and Gun Output Current. These are as follows: Using the front panel interface of E-COAT+3 Master Using the E-GUN+3 C1 Manual type back side interface...
  • Page 28 Picking the second option which is the Controlling via Air Flow, the user will see the below icons on the segments, Powder Transfer Air and Auxilary Air will be set independently. This method is mostly used on Manual System Configurations. Suggestion: For the best surface finishing in automatic systems, it is best to adjust the air flow with Ratio Control.
  • Page 29 PCF-1 Correctional Factor Reference Table Maximum Powder Output Correction Factor PCF1 Before Correction After Correction PCF1 = 5 lt/min 22 gr. PCF1 = 2 lt/min 13 gr. PCF1 = 5 lt/min 14 gr. PCF1 = 5 lt/min 14 gr. PCF1 = 5 lt/min 3 gr.
  • Page 30 Double-Triggering and Sub-Recipe System The E-COAT+3 Master controller unit gives the opportunity to jump between two recipes to its users. The user can switch between any two recipes in a blink of an eye without any need to reach the main controller interface during operation.

  • Page 31: Trigger

    The 1.0 coded POWER IN socket’s inner connections and the fuse connections at the other end should be done by the ELECTRON technicians at the installation. Electron does not accept any responsibility for the possible damage if the equipment is altered or used before installation.

  • Page 32: 4- E-Feed+3 Inj Product Description

    4 .. E-FEED+3 INJ Product Description 4.1. Usage Area The E-FEED+3 INJ Injector is used for conveying the organic type of powder paint used in the industry from any paint hopper to the spray gun where the application is made. E-FEED+3 INJ powder paint injector is supplied ready to use together with special PTFE material made of Teflon bushing and filter module.

  • Page 33: Injector Structure And Power Coat Transfer Principle

    4.2. Injector Structure and Powder Coat Transfer Principle As a result of aerodynamic rules, the air exiting a nozzle creates a vacuum at the recess inlet, which is proportional to the fluid velocity when it is directed from the suction line to a narrower recess as shown in the picture below.

  • Page 34: 5- Powder And Mixture Value Tables

    5. Powder and Mixture Value Tables 5.1. E-FEED+3 INJ General Usage Value The amount of air flowing through the hose and the paint ratio must be adjusted correctly to ensure correct paint output patterns in powder coating application guns. This flow rate is approximately 65-85 lt/min (4-5 m³/s) in a Ø11mm paint hose, while it is approximately 50-85 / min (3-5 m³/s) in a Ø10mm hose.

  • Page 35: Use With E-Coat+3 Master Series Control Units

    5.2.2. Use with E-COAT+3 MASTER Series Control Units For making the “Paint Air” and “Auxiliary Air” settings in E-COAT+3 Master devices front panel the digital screenshots are as follows. E-COAT+3 Master type devices allow the user to operate in a mode where both Auxiliary and Dye Air are adjusted independently and the total air flow in the Powder Coating hose and the paint ratio in this flow are adjusted automatically by the device at the desired levels.

  • Page 36: 6- Cleaning And Mainteace

    6. Cleaning and Maintenance 6.1. Injector Cleaning 1. Quick Coupling 2. Auxiliary Air Filter Module 3. Injector Body 4. Conductive Hose Connection 5. Powder Inlet / Hopper Connection E-FEED+3 INJ injector surface cleaning procedure is as follows. Disconnect the injector from the Hopper. Remove the powder coating hose from the Conductive Hose Connector (4).

  • Page 37: Cleaning Module

    6.2. Cleaning Module When the purge module used in the new injector system is installed on the injector, it delivers high pressure air to the injector through the auxiliary air duct and cleans the system. The check valve (C) used in the system prevents the delivered air from returning to the device.

  • Page 38: Teflon Bushing Module

    6.4. Teflon Bushing Module E-FEED+3 INJ Powder Transmission System In the 1st image, the powder transmission system is assembled. The teflon bushing must be rotated and attached to the injector nozzle and ensure that it is in place. The disassembled version of the powder transmission system is seen in the 2nd image.

  • Page 39: Injector Nozzle Assembly Module

    6.5. Injector Nozzle Assembly Module The injector nozzle assembly can be removed and installed in two simple movements. As seen in the first image, the hose coupling and teflon bushing set can be removed one by one when the assembly is in the unlocked position when rotated.

  • Page 40: Gun+3 C1 General Information

    Electron E-COAT+3 Master and Master P Control Units with proper connections don’t by the trained personnel. The control unit must be earthed with a resistance below 1 M Ohm. Unless the right Zones are defined and the gun is setup without instructed, Electron is not responsible from any damage or potential damage.

  • Page 41: Conformity Between Products

    • Not calibrating the powder, supplementary and nozzle airs. • Humid Powder use Conformity between Products Electron E-GUN+3 C1 manual electrostatic spray gun can be used with the products below: E-COAT+3 Master • E-COAT+3 Master P • E-FEED V2 or E-FEED+3 INJ Injector •...

  • Page 42: Design And Functions

    Weight E-GUN+3 C1 Manual Powder Coating Gun Weight 495 g Usable Powders E-GUN C1 Manual Powder Coating Gun Plastic Coating Powder Conform Metallic Coating Powder Conform Enamel Coating Powder Non-Conform 7.3. Design and Functions 1. Nozzle Group 7. Need Air Input Connection 2.

  • Page 43: Lighting Function

    UI # Function High Voltage Indicator (relevant to brightness) Selected Item Increment Button (If nothing is selected, Powder Increment Button) Selected Item Decrement Button (If nothing is selected, Powder Decrement Button) Segment Selection/Cleaning Mode Selection Gun Light Button 7.4. Lighting Function The lighting function works in two options.

  • Page 44: Lighting Function

    Lighting Function Light is On Light is Off 7.5. Optional Attachments FastPurge™ Fast Cleaning Module • FastCorona™ De-Ionizer Ring • Nozzle Extensions Types • Different Nozzle Types • Gun Cable Extension • * For more information please check the Spare Parts Selection Guide.

  • Page 45: Working Principle

    7.6. Working Principle 7.6.1. High Voltage Generation Electrostatic Powder Coating Conrol Unit sends at most 20 Vp-p valued 17 kHz electrical signal to the E-GUN+3's. This signal which travels through the gun cable to the gun reaches an item called “Cascade”...

  • Page 46: Flat Type Nozzle Structure

    7.6.2. Flat Type Nozzle Structure Flat Type Nozzle creates a hand fan shape on the powder while operating and also ensures that the powder is loaded as intended. The nozzle loads the high voltage from the output center to the powder.

  • Page 47: Fast Corona Ring

    7.6.4. Fast Corona Ring The Fast Corona Ring is an optional extension for the gun, allowing for a better surface quality when coating with the powder coating equipment. The performance of the gun with Fast Corona Ring is convincing due to its very good charging and very high deposition rate as well as an improved penetration into Faraday cages.

  • Page 48: 8- Cleaning And Maintenance

    Part Change The user can only change the consumables of the gun and some of the E-GUN+3 coating gun parts. Note: Operations like Changing the Cascade, Trigger mechanism or Gun Cable can only be done by an ELECTRON® approved personnel. Troubleshooting The failures which are mentioned above can be observed from the “kV “titled segment in the front panel of the...
  • Page 49 There isn’t any high voltage and the 2. Fix the cable to the socket. control unit is flashing with kV and μA fixed to the socket 3. Consult an ELECTRON expert. signs 3. Gun cable is damaged. 4. Cascade is damaged.

  • Page 50: E-Coat+3 Master Device Error Codes

    Device to Gun output/Gun cable is open-circuited or NO GUN or CASCADE IS cascade is defective or NO GUN DETECTED. OSCILLATION original Electron cascade is OUTPUT IS TURNED OFF. not found. Check Gun, Gun Cable or Cascade Connections. PNEUMATIC Lower supplementary air value...

  • Page 51: 10-Parts And Accessories

    Parts and Accessories Product Product Name Order Code A06ECA01A+3 E-COAT+3 Master A Automatic Bare Kit A06ECM01B+3 E-COAT+3 Master B Manuel Bare Kit A06ECM01H+3 E-COAT+3 Master H A06ECM01M+3 E-COAT+3 Master M A06ECM01HD+3 E-COAT+3 Master H Dual A06ECM01MD+3 E-COAT+3 Master M Dual...
  • Page 52 Control Unit Type Order Code E-COAT+3 MASTER CONTROL UNIT B07ECMU01+3 Part No Part Name Order Code E-COAT+3 DEVICE CASE FRAME B07EC5108 E-COAT+3 MASTER FRONT MEMBRANE B07EC3001 E-COAT+3 CONTROL UNIT CASE B07EC5101 RECOMMENDED Order Code Part Name Wearing Part STOCK PARTS ✓...
  • Page 54 Part No Part Name Order Code E-COAT+3 DEVICE CASE FRAME B07EC5108 E-COAT+3 FRONT SEALING GASKET IZCS01016 E-COAT+3 MASTER FRONT MEMBRANE SET B07EC3001 E-COAT+3 MASTER FRONT MEMBRANE ETKT04014 E-COAT+3 MASTER FRONT ALUMINUM SHEET B07EC5103 E-COAT+3 MASTER DISPLAY BOARD B07500029P E-COAT+3 MASTER POWER CARD ELON09030 E-COAT+3 MASTER ROTARY CARD B07500031...
  • Page 55 Part No Accesory Type Order Code E-COAT+3 PLATFORM MOUNTING KIT B07ECT004+3 E-COAT+3 WALL MOUNTING KIT B07ECT003+3 E-COAT+3 SINGLE STAND KIT B07ECT005+3 E-COAT+3 MOBILE STAND KIT B07ECT101 E-COAT+3 MOBILE STAND DUAL KIT B07ECT106 E-COAT+3 MULTICOLOR KIT B07ECT102 E-COAT+3 MULTICOLOR DUAL KIT B07ECT107 Part No Order Code...

  • Page 57: Order Code

    RECOMMENDED Wearing PART # ORDER CODE PART NAME STOCK PARTS Part ✓ B10631007 E-GUN+3 NOZZLE TIGHTENING NUT ✓ ✓ B07531002 E-GUN+3 FLAT HEAD GROUP ✓ ✓ B10631001 E-GUN+3 MANUAL GUN PLASTIC BODY (COMPLETE) ✓ B07EGCN02 E-CASCADE+3 ✓ B07BC0003 E-GUN+3 BACK COVER (COMPLETE) ✓...
  • Page 58 Part No Order Code Part Name Wearing Part B07EGC300+3 E-GUN+3 C3 AUTOMATIC POWDER COATING GUN...
  • Page 60 Wearing RECOMMENDED Part No Order Code Part Name Part STOCK PARTS B10631007 E-GUN+3 C3 NOZZLE TIGHTENING NUT ✓ ✓ B10632001 E-GUN+3 C3 PLASTIC FRONT BODY ✓ B07EGCN02 E-CASCADE+3 ENEM04012 E-GUN+3 C3 CASCADE ISOLATION GASKET TRTM06245 E-GUN+3 C3 INSIDE ASSEMBLY PART BECV03128 M6X60 CYLINDER HEAD CAP SCREW BEPL03002...
  • Page 61 RECOMMENDED Part No Part Name Order Code Wearing Part STOCK PARTS E-GUN GUN CABLE EXTENSION KIT 5 M B07EXT005 E-GUN GUN CABLE EXTENSION KIT 10 M B07EXT006 RECOMMENDED Part No Part Name Wearing Part Order Code STOCK PARTS 11X16 POWDER HOSE w/ DOUBLE CARBON ✓...
  • Page 62 RECOMMENDED Part No Order Code Part Name Wearing Part STOCK PARTS COMPOSITE RECIPROCATOR ARM B07RCA301 ✓ AKUA03002 E-GUN+3 C3 COMPOSITE RECIPROCATOR ARM 750 MM ✓ ✓ RECIPROCATOR ARM PAINT TRANSFER PIPE (COMPL.) B07RCA302 RECIPROCATOR ARM BACK COVER B06CE05001...
  • Page 63 Part No Order Code Part Name Wearing Part E-GUN+3 C3 FAST CORONA RING B07FCR301 B07FCR302 E-GUN+3 C1/C2 FAST CORONA RING E-GUN+3 FAST CORONA RING CHARGE COLLECTOR TRTM04199 TRTM04201 E-GUN+3 FAST CORONA RING SHAFT Ø6XL193 BEDH09017 E-GUN+3 FAST CORONA LOCKING SPRING BEDH09016 E-GUN+3 FAST CORONA LOCKING BASE SPRING SCREW M2,5X5...
  • Page 64 If any extension head assembly is used, the gun is no longer comply with the explosion protection regulation.
  • Page 65 Wearing RECOMMENDED Part No Order Code Part Name Part STOCK PARTS E-GUN+3 150 MM EXTENSION HEAD GROUP - DEFLECTOR B07EXT031D B07EXT032F E-GUN+3 150 MM EXTENSION HEAD GROUP - FLAT B07EXT032D E-GUN+3 250 MM EXTENSION HEAD GROUP - DEFLECTOR B07EXT032F E-GUN+3 250 MM EXTENSION HEAD GROUP - FLAT B07EXT033D E-GUN+3 400 MM EXTENSION HEAD GROUP - DEFLECTOR E-GUN+3 400 MM EXTENSION HEAD GROUP - FLAT...
  • Page 68 Wearing RECOMMENDED Part No Order Code Part Name Part STOCK PARTS E-GUN+3 45° ANGLED HEAD GROUP - DEFLECTOR B07EXT034D B07EXT034F E-GUN+3 45° ANGLED HEAD GROUP - FLAT ENEM01051 E-GUN 45° ANGLED ELECTRODE MALE PART O-RİNG Ø18X1,5 IZOR01007 TRTM01022 FLAT HEAD GROUP CONICAL ISOLATOR ENEM01048 ANGLED EXTENSION ELECTRODE RESISTOR SHAFT FRONT T PART...
  • Page 69 FLAT TO DEFLECTOR HEAD GROUP REPLACEMENT IN 6 STEPS Note: The steps shown can be applied to only ''complete set'' kits.
  • Page 70 RECOMMENDED Part No Order Code Part Name Wearing Part STOCK PARTS ✓ E-GUN+3 FLAT CAP PATTERN ADJUSTER TRTM03112 B07EGC100+3 E-GUN+3 C1 MANUAL GUN B07EGC300+3 E-GUN+3 C3 AUTOMATIC GUN (Not Shown) B07EGC200+3 E-GUN+3 C2 MANUAL GUN (Not Shown) NARROW PATTERN FOCUSED PATTERN STANDARD PATTERN The Pattern adjuster attached to the tip of the manual or automatic gun ensures that the paint coming out of the gun is formed in a narrowed form.
  • Page 71 RECOMMENDED Part No Order Code Part Name Wearing Part STOCK PARTS ✓ ✓ E-GUN+3 FLAT ELECTRODE GROUP B07531006 ✓ ✓ E-GUN+3 ELECTRODE GROUP WITH DEFLECTOR B07531007 ✓ ✓ E-GUN+3 FLAT HEAD GROUP B07531002 ✓ ✓ E-GUN+3 HEAD GROUP WITH DEFLECTOR B07531008...
  • Page 72 Wearing RECOMMENDED Part No Order Code Part Name Part STOCK PARTS ✓ ✓ TRTM08282 E-GUN+3 Ø35 CARBON RING ✓ ✓ B10631003D E-GUN+3 ELECTRODE BODY ✓ ✓ TRTM01022 E-GUN+3 FLAT HEAD GROUP CONICAL INSULATOR ✓ ✓ TRTM01046 E-GUN+3 FLAT CAP ✓ ✓...
  • Page 73 Part Name Part # Order Code B07FEED+3 E-FEED+3 INJ INJECTOR PNBE01005 SPRING BODY QUICK CONNECTION 8X6 MM *** Sold as 1 piece.
  • Page 75 Wearing RECOMMENDED Part # Order Code Part Name Part STOCK PARTS TRTM05035 E-FEED+3 FEMALE QUICK CONNECTION ADAPTER ✓ B10540005 E-FEED+3 INJECTOR NUT ✓ ✓ E-FEED+3 INJECTOR HOSE CONNECT COUPLING W/O-RING B07610032 ✓ ✓ B10640034 E-FEED+3 INJECTOR HOSE CONNECT COUPLING IZOR01051 O-RING Ø13X2 ✓...
  • Page 76 Order Code Part Name B07PURGE01 FastPurge™ Module Part Name Part No Order Code B07542000 FastPurge™ MAIN BODY ASSEMBLY B07EC0019 FastPurge™ VALVE ASSEMBLY PNPE04001 ¼” 3/2 WAY VALVE WITH ATEX COIL PNRD01014 FLAT FITTING 1/4’-Ø8 MALE PNRD03009 PNEUMATICAL ROTATING ELBOW 1/4”- Ø8 MALE B07ECK511 FastPurge™...
  • Page 77 RECOMMENDED Part No Order Code Part Name Wearing Parts STOCK PARTS TRTM04018 FastPurge™ MAIN BODY B07EC0016 FastPurge™ LOCKING SHAFT SET ASSEMBLY TRTM07005 FastPurge™ LOCKING SHAFT BARREL TRTM07006 FastPurge™ LOCKING SHAFT SPRING HOLDER BEDH09006 FastPurge™ LOCKING SHAFT SPRING TRTM07004 FastPurge™ LOCKING SHAFT B07EC0017 FastPurge™...
  • Page 79 Part No Order Code Part Name Wearing Part B07ECCA011 E-COAT+3 MULTICOLOR SUCTION TUBE ASSEMBLY TRTM03067 E-COAT+3 MULTICOLOR SUCTION TUBE HOLDER BUSHING BEDH13024 E-COAT+3 MULTICOLOR SUCTION TUBE LOCK ✓ B07ECM003+3 E-COAT+3 MULTICOLOR SUCTION TUBE B07ECCA007 E-COAT+3 MULTICOLOR SUCTION TUBE BRACKET ASSSEMBLY BEPL04009 LOCK WASHER TRTM04185...
  • Page 80 RECOMMENDED Part Name Wearing Part Part No Order Code STOCK PARTS B07ECM003+3 E-COAT+3 MULTICOLOR SUCTION TUBE TRTM03022 E-COAT+3 MULTICOLOR SUCTION TUBE TOP LID SCBR08002 E-COAT+3 MULTICOLOR SUCTION TUBE (1) L:560 SCBR06006 E-COAT+3 MULTICOLOR SUCTION TUBE (2) L:560 ✓ ✓ IZOR01006 ORİNG Ø16X2 TRTM03024 E-COAT+3 MULTICOLOR SUCTION TUBE ADAPTER BOTTOM BODY ✓...
  • Page 81 Part No Order Code Part Name Wearing Part AKUA08006 E-COAT+3 MOBILE TROLLEY FRONT WHEEL AKUA08005 E-COAT+3 MOBILE TROLLEY BACK WHEEL 200X50 TRTM04048 E-COAT+3 MOBILE TROLLEY BACK WHEEL SHAFT BECV06005 BOLT M6X20 YHB B06CE20025 E-COAT+3 MOBILE TROLLEY HOSE CABLE HANGER B06CE20034 E-COAT+3 MOBILE TROLLEY HOPPER PATCH BLOCK PNPE07002 MANOMETER Ø40 2,5 BAR...
  • Page 82 Part No Order Code Part Name A05EH0050+3 E-HOPP50+3 50 LT STAINLESS POWDER COATING HOPPER A05EH0050D+3 E-HOPP50+3 DUAL 50 LT STAINLESS POWDER COATING HOPPER...
  • Page 84 RECOMMENDED Part No Order Code Part Name Wearing Part STOCK PARTS B06CE02001 E-HOPP50+3 HOPPER MAIN BODY B06CE02004 E-HOPP50+3 HOLDER ASSEMBLY SCSC05003 E-HOPP50+3 BOTTOM LID ✓ ✓ FRFL07003 E-HOPP50+3 FLUIDIZATION PLATE ✓ ✓ IZCS02001 E-HOPP50+3 FLUIDIZATION PLATE GASKET B06CE02003 E-HOPP50+3B BOTTOM LID LOCK TRTM04041 E-HOPP50+3 BODY HOLDER B10C0003...

  • Page 85: 11- Service And Maintanence Table

    11.Service an Maintenance Table Maint. Type -Weekly DATE CONTROL MAINT. OR SERVICE PROCEDURE CHANGED -Yearly SUPERVISOR PERSONNEL PART NOTES -Service...

  • Page 86: 12-Product Life And Warranty

    Product Life and Warranty 12.1. Product Life • The economic life of E-COAT+3 Master is approximately 10 years. • This product life is highly dependent on the periodic maintenances and spare part changes in a timely manner. Improper maintenance will lead to lower product life. •...
  • Page 87 PERPA Tic. Mer. B-Blok Kat:2 No:65 İTOB Org. San. Bölgesi 10010 Sk. No:10 34385, Okmeydanı – İSTANBUL/TÜRKİYE 35470, Menderes – İZMİR/TÜRKİYE Telefon: +90 (212) 222 23 45 Telefon: +90 (232) 799 02 32 Mail: info@electron.com.tr Fax: +90 (232) 799 02 42...

This manual is also suitable for:

E-coat+3 master hE-coat+3 master h dualE-coat+3 master mE-coat+3 master m dual

Table of Contents