Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Toua GSN40B-30
Summary of Contents for Toua GSN40B-30
- Page 1 MODEL GSN40B-30 GSN40B-40 GAS CONCRETE NAILER SAFETY OPERATE MANUAL ...
-
Page 2: Table Of Contents
CONTENTS ITEM PAGE SAFETY ..............1 2. SPECIFICATION ............6 3. GENERAL OPERATION MANUAL .... 4. MAINTENANCE .......... EXPLODED DRAWING AND PARTS LIST ... 20 ... -
Page 3: Definitions Of Signal Words
SAFETY IMPORTANT INFORMATION MUST TO KNOW BEFORE TO READ IMPORTANT SAFETY INSTRUCTIONS FOR Read and understand tool labels USING NAILERS and all of operating instructions, READ ALL INSTRUCTIONS safety precautions and warnings in This Nailer is powered by internal this manual before operating or combustion device. -
Page 4: Keep Work Area Clean
Keep the Nailer, fuel cells and battery 9. STORE NAILER PROPERLY WITH FUEL CELL 120°F MAX away f rom sunshine and from AND BATTERY REMOVED. (50 ) temperature exceeding 120°F When not in use, the Nailer, fuel cell and battery (50°C). - Page 5 17. PLACE NAILER PROPERLY ON WORKPIECE. Do not operate the Nailer when you are tired. Do not drive fasteners on top of other fasteners The Nailer should never be used by you if you or with the Nailer at too steep of an angle; the are under the influence of alcohol, drugs or fasteners can ricochet and hurt someone.
-
Page 6: Battery Charger
FUEL CELL IMPORTANT SAFETY INSTRUCTIONS I MP OR TA NT S AF ET Y IN ST RU CT IO NS FOR BATTERY CHARGER DANGER WARNING ■ Fuel cell, fuel and propellant are flammable under pressure. Death or serious bodily injury could result from Explosion / Fire Hazard improper or unsafe use of battery chargers. -
Page 7: Important Safety Instructions For Use Of The Battery And Battery Charger
Table 1 3. DO NOT short-circuit the battery. RECOMMENDED MINIMUM AWG SIZE FOR 4. DO NOT insert any objects into the battery EXTENSION CORDS FOR BATTERY CHARGERS charger's air vents. Electric shock or AC Input Rating Amperes AWG Size of Cord damage to the battery charger may result. -
Page 8: Specification
SPECIFICATION 1．GAS CONCRETE NAILER TYPE GSN40B-30 GSN40B-40 Type of power Piston reciprocating Applicable nails See 2. Available Nails. Kinetic Energy 90(joule) Nail Capacity 32 nails （3- strip） 42 nails （4- strip） Ambient temperature -5 ℃～ 50℃(23 ℉to 120 ℉) 14.17 ＂... - Page 9 NOTE: When fire the plastic strip nail to the common concrete, should pay attention to control the nail fire place with the concrete marginal range and the nail between the nail range, if the distance undersize, the concrete will easy to crack to injure yourself or someone around you. Suggest the nail fire place with the concrete marginal range no less than 50mm, nail between the nail ranges no less than 60mm.
-
Page 10: General Operation Manual
The information contained in this Manual is designed to assist you in the safe operation of the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer. NAME OF PARTS 1. Gas Concrete Nailer ( MODEL: GSN40B-30 GSN40B-40) Latch Top Cover Cell Cover... -
Page 11: Removal And Installation Method Of Battery
4. Accessories 1. How to install the battery Align the battery with the groove in tool handle and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. -
Page 12: Before Operation
NOTE: The battery charging time becomes longer ■ If the battery charger does not work while the when a temperature is low or the voltage of battery is mounted correctly, it is probable that the power source is too low. the battery or charger is malfunctioning. -
Page 13: Preparing The Battery
■ Do not spray to a naked flame or MAGAZINE ASSEMBLY INSTALL any incandescent material. (1) REMOVE FUEL CELL AND BATTERY FROM ■ Do not smoke when handling NAILER. fuel cell. ■ Keep stem of fuel cell away from (2) Fit on the magazine assembly.Insert magazine face or skin. - Page 14 Flashing GREEN: Enough power remaining Before actually beginning the nailing work, test the (The light turns steady during operation). Nailer by using the checklist below. Conduct the Flashing RED: Insufficient power remaining tests in the following order. (The light turns steady during operation). If abnormal operation occurs, stop using Nailer and contact a dealer authorized service center immediately.
-
Page 15: Loading Nails
Nail Feeding Step (4) Remove the finger from the trigger and press the (1) Insert nails into the back of the magazine push lever against the workpiece with pulling (see chart a) backward the feeder knob, motor fan start. Do not pull the trigger Plastic strip nails... -
Page 16: Nailer Operation
■ Do not touch around the exhaust Removing the nails: outlet with bare hands. (1) Pull the feeder knob backward to leave the The push lever and nose will nails a little distance, press the knob of the nail become hot and get heated up feeder (see chart e) . -
Page 17: Methods Of Operation
Nail Jam Remove downward nailer 2~3 times, pulling the trigger , In fire process meet the nail jam malfuction,remove the nails will be driven. Or use after put the it according the following steps: nailer and fuel cell indoor 30 minutes. (1) Remove the fuel cell and the battery;... -
Page 18: Using The Hook
MAINTENANCE Note When the pins are fire into smooth surface, suggest use the pushing arm jacket, such as NOTE: the sheet steel; ■ The information contained in this Manual is designed When nails are fire into the wood, suggest to assist you in the safe maintenance of the Nailer. -
Page 19: Warning Label
■ When not in use, the Nailer, fuel cell and battery Cleaning time intervals form should be stored in a warm and dry place. Operation Environment very dirty dirty c ommon clean ■ Keep it out of reach of children. 1000 1 Week 2 Week... -
Page 20: Operator Troubleshooting
Operator troubleshooting PROBLEM CHECK METHOD CORRECTION Check for a jam nails. Clear a jam nails. Nailer operates, Check for proper nails. Use only recommended nails. but no nail is driven. Check for a jam . Clear a jam. Check function of nail feeder . Clean and lubricate. - Page 21 ...
-
Page 22: Exploded Drawing And Parts List
EXPLODED DRAWING AND PARTS LIST GAS CONCRETE NAILER MODEL: GSN40B-30 GSN40B-40 42 43 Note: screw torque and description 501-1 501-2 Torsion(Nm) Note 1～1.2 Thread glue (loctite 277) 1.8～2 Thread glue (loctite 277) 3～3.5 Thread glue (loctite 272) 11 1 3.5～4... - Page 23 PART LIST Note : consumable parts GSN40B-30/GSN40B-40 Parts Name Qty Remark Parts Name Qty Remark 1 Hex Bolt M5×10 63 Locknut 2 Top Cover 64 Right Handle 3 Filter 65 Lock block ...
- Page 24 ...
Need help?
Do you have a question about the GSN40B-30 and is the answer not in the manual?
Questions and answers