Copyright Notice This document is copyrighted, 2024. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft®, Windows®, Windows® 10 IoT Enterprise are registered trademarks ⚫ of Microsoft Corp. Intel® is a registered trademark of Intel Corporation ⚫ Yocto Project® is a trademark of The Linux Foundation. ⚫...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UPS-ASL01 (UP Squared 7100) with Heatsink ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document.
Page 6
Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System Processor Intel® Processor N97 Intel Processor N100 ® Graphics Intel UHD Graphics for 12th Gen Intel Processors ® ® Memory Up to 16GB LPDDR5 Storage Up to 128GB eMMC HDMI 2.0b x 1 DP 1.2 x 1 eDP 1.3 x 1 Audio Wafer x 1 (Line out + Mic in) RS-232/422/485 via Wafer x 2 Camera...
Page 15
Power Requirement Power 12V DC-in Power Supply Type AT/ATX (ATX as default) Power Consumption 15W ~ 37W (Typical) Mechanical Dimension 3.37" x 3.54" (85.6mm × 90mm) Net Weight 0.41 lb. (0.19Kg) Gross Weight 0.66 lb. (0.3Kg) Environmental Operating Temperature 32°F ~ 140°F (0°C ~ 60°C) / 0.5 airflow Operation Humidity 0% ~ 90% relative humidity, non-condensing MTBF...
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers and connectors that you can configure for your application Label Function Power Button BIOS Update Connector eDP Connector USB & UART M.2 M-Key Slot CN29 Dual USB 3.0 (Type-A) Port 40 Pin HAT...
2.3.1 Power Button (SW1) Signal Signal Power Button Signal 2.3.2 BIOS Update Connector (CN1) Signal Signal SPI_MISO SPI_CLK SPC_CS0# +1.8V SPI_MOSI Chapter 2 – Hardware Information...
Signal Signal Signal CNV_WT_CLK_D- +3.3V/2.5A CNV_WT_CLK_D+ +3.3V/2.5A Note: Total 2.5A for M.2 E-Key Slot. 2.3.10 Dual LAN (CN12) Signal Signal Signal LAN1_MDI0+ LAN2_MDI0+ LAN1_ACTLED- LAN1_MDI0- LAN2_MDI0- LAN1_ACTLED+ LAN1_MDI1+ LAN2_MDI1+ LAN1_LINK100# LAN1_MDI1- LAN2_MDI1- LAN1_LINK1000# LAN1_MDI2+ LAN2_MDI2+ LAN2_ACTLED- LAN1_MDI2- LAN2_MDI2- LAN2_ACTLED+ LAN1_MDI3+ LAN2_MDI3+ LAN2_LINK100# LAN1_MDI3-...
2.3.11 USB 3.0 (Type-A) Port (CN13) Signal Signal +5V/2A USB2_D3- USB2_D3+ USB3_RX- USB3_RX+ USB3_TX- USB3_TX+ 2.3.12 RTC (CN14) Signal Signal RTC_VCC Chapter 2 – Hardware Information...
2.3.13 Front Panel (CN17) Signal Signal RESET Power Button 2.3.14 Audio Wafer (CN18) Signal Signal LINE_OUT_Right LINE_OUT_Left AUDIO_GND MIC_IN Chapter 2 – Hardware Information...
2.3.15 Fan Connector (CN19) Signal Signal TACH +12V/1.5A 2.3.16 DC Power Jack (CN20) Signal Signal DC_IN GND_Signal Chapter 2 – Hardware Information...
Linux Setup The UP Squared 7100 supports Linux operating systems (see Chapter 1 for specifications). For instructions on how to install a Linux OS onto your UP Squared 7100, you can find several guides and tutorials in the wiki section of the UP website at https://up-board.org for both installing supported distributions as well as porting your own Linux build.
Cables and Connectors This table provides detailed information about the cables and connectors used by the UP Squared 7100. If you have any questions about the configuration of your board, please contact your AAEON sales representative. Mating Connector AAEON Label Function Vendor Model No.
Need help?
Do you have a question about the AAEON UP Squared 7100 and is the answer not in the manual?
Questions and answers