Advertisement
Quick Links
Technical Support and E-Warranty Certificate www.vevor.com/support
Kids' Balance Bike
MODEL: YC-16
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Related Manuals for VEVOR YC-16
Summary of Contents for VEVOR YC-16
- Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support Kids’ Balance Bike MODEL: YC-16 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
- Page 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
- Page 3 INSTRUCTIONS Thank you very much for choosing this Kids’ Balance Bike. Please read all of the instructions before using it.The information will help you achieve the best possible results. WARNING: Please read this manual carefully before using the product. Failure to do so may result in serious injury.
-
Page 4: Installation And Use
Installation and use serial number parets name serial number parets name bell auxiliary wheel ① ⑫ brake crank hind wheel ② ⑬ Handlebar Rear inlet brake ③ ⑭ sheathing Front fork lock shock absorber ④ ⑮ female Front clamp Rear fender ⑤... -
Page 5: Installation Instructions
Installation instructions STEP1: Loading handlebars: As shown in Figure 1, insert the riser into the front riser again, adjust the insertion depth to the position suitable for the height of the rider, tighten the lifting screw (tighten the lifting screw torque is not less than 18N.m) Note: The minimum insertion depth is subject to the safety line cannot be seen. - Page 6 STEP2: Install auxiliary wheel: as shown in Figure 2, remove the rear axle nut and washer (thin nut and limit plate need not be removed), then set the upper limit piece, auxiliary wheel carrier washer and nut in turn, adjust the auxiliary wheel height, tighten the nut (the torque of the tightening nut is not less than 30N.m), adjust and remove the auxiliary wheel: when adjusting the auxiliary wheel, loosen the side nut.
- Page 7 STEP4: Install the pedal: As shown in Figure 4, first identify the letter "R" at the top of the pedal shaft means right, "L" means left, and use a wrench to install the pedal marked "R" on the right crank of the bicycle (one side of the chain cover) in a clockwise direction, and the pedal shaft should be fastened with the crank, and should not be loose.
- Page 8 tube into the riser, the minimum insertion depth is subject to the safety mark cannot be seen). Apply 160N-200N force to lock the tail of the quick release handle along the direction of quick release closure. Insert the saddle into the saddle tube to adjust the direction of the saddle, lock the saddle nut (locking torque is not less than 15N.m) Adjust the direction of the mud plate and tighten the nut (tightening torque is not less than 3N.m)
- Page 9 effect is increased, and the shock absorber effect is reduced. (Torque of locking nut at both ends of shock absorber is not less than 12N.m) STEP8: Install brake wire and bell: As shown in Figure 8, first loosen the adjusting nut and adjusting bolt on both brake bars counterclockwise so that the opening is in line with the opening of the brake bar, then clamp the round head of the front brake wire into the front end of the brake groove of the right handlebar (the round...
-
Page 10: Maintenance And Repair
knowledge for details). If the brake cover is to the left, gently tap the left side of the spring with the steel bar and vice versa, tap the right side). Make the rim the same distance from the left and right brake skins. STEP10: Adjust the brake: If the amount of adjustment is small, loosen the adjusting nut on the brake first, adjust the hollow screw, so that the brake skin (the steel belt of the brake) and the hoop in the brake keep a small gap, and tighten the... - Page 11 4. Electroplating parts: If the surface is found to be yellowish-brown network, you can use neutral oil or sewing machine oil to wipe frequently to prevent the network from expanding. 5. The front bowl is loose: first loosen the front and lock the mother, remove the gasket, and then adjust the gap between the upper bowl and the steel ball with a wrench, and then install the gasket and tighten the front and lock the mother.
- Page 12 Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the YC-16 and is the answer not in the manual?
Questions and answers