1. Manuals
  2. Brands
  3. Unity Manuals
  4. Industrial Equipment
  5. USK02
  6. User manual

Unity USK02 User Manual

Sync card device
Hide thumbs

Advertisement

Table of Contents

USK02 SYNC CARD DEVICE
USER MANUAL
2024
VER.2/22.02.2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the USK02 and is the answer not in the manual?

Questions and answers

Related Manuals for Unity USK02

Summary of Contents for Unity USK02

  • Page 1 USK02 SYNC CARD DEVICE USER MANUAL 2024 VER.2/22.02.2023...
  • Page 2 CONTENTS 1.Safety precaut ons..................2 2.Warn ngs for safe use and nstallat on.………………....………………..4 3.Overv ew..................5 4.General and techn cal spec f cat ons............6 5.Where s t used?...................7 6.Connect on d agram..................8 7.Flow d agram....................9 8.Techn cal draw ng......................9.

  • Page 3: Security Measures

    SECURITY MEASURES 1-) Product select on su table for a healthy safe work ng env ronment should be made and the dev ce should be used accordance w th the nstruct ons. 2-) Necessary checks, ma ntenance and clean ng of the dev ce must be carr ed out before product on.
  • Page 4 SECURITY MEASURES 5-) Attent on should be pa d to the l ght ng of the env ronment depend ng on the locat on of the dev ce. 6-) It should be mandatory for employees to comply w th the safety measures s gns env ronment.
  • Page 5 SAFE USE WARNINGS Before perform ng any operat on on the dev ce, d sconnect all supply voltages. Do not d sassemble the dev ce wh le t s under power. Do not clean the dev ce w th solvents or s m lar substances. Use only dry cloth to clean the dev ce.
  • Page 6 OVERVIEW UNITY USK02 synchronous card s des gned for use n ndustr al automat on appl cat ons, tak ng nto account ts dynam c des gn. Sensors, PLCs, transm tters, etc. n the f eld n ndustr al env ronments. It s produced to solate the 0-10 Volt analog s gnals produced by dev ces from electr cal no se n the env ronment and to carry them to remote locat ons.
  • Page 7 GENERAL AND TECHNICAL SPECIFICATIONS INPUT FEED 220 VAC OPERATING TEMPERATURE 0-50° PROTECTION CLASS IP 20 INSTALLATION METHOD RAY TIP DIMENSION 70 X 85 X 58 INPUT VOLTAGE 0-10V OUTPUT VOLTAGE 0-10V www.un tygrup.com All data is subject to change without prior notice.

  • Page 8: Where To Use

    WHERE TO USE? · Dr ver speed control. · Control of l ne speed reference. · Potent ometer feeds. · PLC Analog output. · Used to solate the output of many transm tters. www.un tygrup.com All data is subject to change without prior notice.

  • Page 9: Connection Diagram

    CONNECTION DIAGRAM www.un tygrup.com All data is subject to change without prior notice.

  • Page 10: Steps To Follow

    STEPS TO FOLLOW 1.Take the dev ce out of ts box and check t. 2. Read page 8 before start ng the assembly of the dev ce. 3. Read page 6 before start ng the nstallat on of the cables suppl ed w th the dev ce.

  • Page 11: Technical Drawing

    TECHNICAL DRAWING www.un tygrup.com All data is subject to change without prior notice.

  • Page 12: Our Contact Information

    OUR CONTACT INFORMATION Address: Telephone: +90 212 549 30 56 GSM: +90 552 366 30 56 Ma l: nfo@un tygrup.com www.un tygrup.com www.un tygrup.com All data is subject to change without prior notice.

Table of Contents