Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for eltherm ELSR
Summary of Contents for eltherm ELSR
- Page 1 INSTALLATION MANUAL ELSR & ELP Installation and operation self-regulating & parallel heating cables eltherm GmbH Ernst-Heinkel-Strasse 6 -10 57299 Burbach, Germany P.: +49 2736 4413-0 QAA 023 F.: +49 2736 4413-50 Rev.10 info@eltherm.com www.eltherm.com...
-
Page 2: Table Of Contents
CONTENTS Topic Page INTRODUCTION GENERAL INFORMATION WARRANTY INCOMING GOODS STORAGE LENGTH OF HEATING CIRCUIT MOUNTING SAFETY INSTRUCTIONS PREPARATION OF MOUNTING MOUNTING THE HEATING CABLE Preparation of the system Unrolling the heating cable Fastening the heating cable to the pipe Fastening the heating cable on pipe supports Fastening the heating cable on elbows Fastening the heating cable on flanges Fastening the heating cable on fittings... - Page 3 QAA 023 Installaton manual ELSR- & ELP heating cables Revision 10 IMPORTANT INFORMATION - RETAIN FOR LATER USE - FOR DISPOSAL Please follow these instructions for proper and safe use of the The WEEE logo indicates that this product must not be disposed ELSR- and ELP heating cables.
-
Page 4: Introduction
INTRODUCTION GENERAL INFORMATION The trace heating systems ELSR-... and ELP-... are suitable for industrial use on pipelines, containers and associated equipment in non-classified (common) areas, outdoor areas, wet areas and areas where flammable gases, dust or fibres may be present. -
Page 5: Preparation Of Mounting
Make sure the sensors are properly arby placed objects! attached. • ELSR types: An overlapping or contacting installation of • For use as trace heating in accordance with IEC EN the heating tape does not cause overheating due to the 62395-1 and IEC EN 60159-10 and for Ex applications, an self-regulating heating characteristic. -
Page 6: Unrolling The Heating Cable
• The electrical connection and termination of the heating vent damage to the heating cable due to excessive tensile cables must only be carried out using eltherm accesso- force. • Unroll the heating cable straight over the edge of the ries in accordance with the relevant assembly instruc- drum, not off to the side. -
Page 7: Fastening The Heating Cable On Pipe Supports
This is the only way to ensure that the burr cannot damage the heating cable. ATTENTION • Observe the specified length allowances in project pla- ning or design (for example in eltherm Designer). Contact us: +49 2736 4413-0 • info@eltherm.com www.eltherm.com... -
Page 8: Fastening The Heating Cable On Elbows
Fastening the heating cable on elbows Fastening the heating cable on fittings heating cable heating cable adhesive tape adhesive tape adhesive tape • When laying a heating cable around a pipe bend, the heating cable must be laid on the outside of the pipe bend. -
Page 9: Fastening The Heating Cable On Plug-In Disc
QAA 023 Installation manual ELSR- & ELP heating cables Revision 10 Fastening the heating cable on Plug-in disc ATTENTION • Make certain the metal braiding has the best possible contact with the surface of the fitting. heating cable • Only fasten the heating cable with the fastening mate- rial provided by the manufacturer and follow the reco- mendations for fastenings. -
Page 10: Cover The Heating Cable With Metal Foil
ELECTRIC HEAT TRACING eltherm GmbH Ernst-Heinkel-Str. 6-10 • 57299 Burbach, Germany Tel.: +49 (0) 27 36 - 44 13-0 • Fax: +49 (0) 27 36 - 44 13-50 info@eltherm.com • www.eltherm.com INSPECTION OF THE HEATING CIRCUIT • Fasten the heating cable onto the braiding •... -
Page 11: Operation & Maintenance
• Heater or attached leads show damage or deformation. Trace heaters ELSR-... and ELP-... generally operate mainte- • The circuit is electrically defective (open circuit, high lea- nance free. However, it is recommended that the system be kage current). - Page 12 This document can also be found on the eltherm website. Visit our download area. eltherm GmbH Ernst-Heinkel-Straße 6 -10 57299 Burbach. Germany T.: +49 2736 4413-0 F.: +49 2736 4413-50 info@eltherm.com www.eltherm.com...
Need help?
Do you have a question about the ELSR and is the answer not in the manual?
Questions and answers