1. Manuals
  2. Brands
  3. Rosehill Wine Cellars Manuals
  4. Racks & Stands
  5. CALIFORNIA INDIVIDUAL 8 COLUMN F01 (A)
  6. Assembly installation manual

Rosehill Wine Cellars CALIFORNIA INDIVIDUAL 8 COLUMN F01 (A) Assembly Installation Manual

Redwood winerack
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

CALIFORNIA REDWOOD WINERACK
INDIVIDUAL MODULES
INDIVIDUAL 8 COLUMN F01 (A)
INDIVIDUAL 8 COLUMN F01(B)
32" x 32"
32" x 48"
INDIVIDUAL 4 COLUMN F02(A)
INDIVIDUAL 4 COLUMN F02(B)
16" x 32"
16" x 48"
INDIVIDUAL 5 COLUMN F03 (A)
INDIVIDUAL 5 COLUMN F03(B)
(1/2 bottles)
(1/2 bottles)
16" x 32"
16" x 48"
ASSEMBLY & INSTALLATION GUIDE
Rosehill Wine Cellars | Toll Free: 1-888-253-6807
www.rosehillwinecellars.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CALIFORNIA INDIVIDUAL 8 COLUMN F01 (A) and is the answer not in the manual?

Questions and answers

Related Manuals for Rosehill Wine Cellars CALIFORNIA INDIVIDUAL 8 COLUMN F01 (A)

Summary of Contents for Rosehill Wine Cellars CALIFORNIA INDIVIDUAL 8 COLUMN F01 (A)

  • Page 1 INDIVIDUAL 4 COLUMN F02(B) 16” x 32” 16” x 48” INDIVIDUAL 5 COLUMN F03 (A) INDIVIDUAL 5 COLUMN F03(B) (1/2 bottles) (1/2 bottles) 16” x 32” 16” x 48” ASSEMBLY & INSTALLATION GUIDE Rosehill Wine Cellars | Toll Free: 1-888-253-6807 www.rosehillwinecellars.com...
  • Page 2 TOOLS 1”-1 ” Finishing Nailer Highly recommended to prevent splitting of wood. This tool is also handy for projects around the home. 8 ” Philips Screwdriver Hammer Level Drill COMPONENTS Inner Column Outer Column Horizontal Bar HARDWARE 1/2” Screw x 8 7/8”...

  • Page 3: Getting Started

    GETTING STARTED IMPORTANT NOTE : Individual WineRack modules are available in a variety of sizes. The Indi- vidual 8 column, type B (F01B) is illustrated in the following instructions. Other models have fewer columns or bars, but method of construction is the same.
  • Page 4 STEP 2 ASSEMBLE BARS AND COLUMNS : Make sure all column TOPS are orientated in the same direction. For identifying the TOP and BOTTOM refer to circled zoom views. Place inner and outer columns in the notches of the horizontal bars. Place remaining horizontal bars down over columns, so that all notches interlock.
  • Page 5 STEP 3 NAIL HORIZONTAL BARS TO COLUMNS : Use wall or floor to keep rack steady while nailing. Using a finishing nailer gun will reduce spliting of wood and speed up assembly. Nail intersections together as shown ( figure A ). Nail through outer columns into ends of horizontal bars ( figure B ).
  • Page 6 STEP 4 FASTEN BRACKETS TO WINERACK AND WALL : Place Brackets in position under horizontal bars. Fasten 1/2” screws through holes of brackets ( figure A ). BEFORE ATTACHING TO WALL : For a professional look, install a Base Trim Kit* before mounting rack to wall. (Shown on last page) - Stand winerack in position at wall.

  • Page 7: Multiple Modules

    MULTIPLE MODULES If installing multiple modules, screw adjoining racks together. Fasten through adjoining bars with 7/8” screws at top, middle and bottom rows, as shown. To avoid cracking, pre-drill 1/16” holes for screws. Fasten through rear rack sections as well as front. If stacking modules, fasten adjoining horizontal bars in at least two places.

  • Page 8: Test Before Use

    TEST BEFORE USE Use of WINERACK is strictly at your own risk. Drobot Inc. will not accept any responsibility or liability for damages resulting from units not assem- bled precisely as directed, or not securely fastened to a wall or support with suitable fasteners.

This manual is also suitable for:

Individual 8 column f01(b)Individual 4 column f02(a)Individual 4 column f02(b)Individual 5 column f03 (a)Individual 5 column f03(b)

Table of Contents