Gemini GVC150RD Manual
Gemini GVC150RD Manual

Gemini GVC150RD Manual

22.2v cordless stick vacuum cleaner with motorized bed brush

Advertisement

22.2V CORDLEss sTICK
VaCuuM CLEaNER wITh
MOTORIzED bED bRush
22.2V無線直立式床刷吸塵機
MODEL NO.: GVC150RD
A GILMAN GROUP BRAND
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GVC150RD and is the answer not in the manual?

Questions and answers

Summary of Contents for Gemini GVC150RD

  • Page 1 22.2V CORDLEss sTICK VaCuuM CLEaNER wITh MOTORIzED bED bRush 22.2V無線直立式床刷吸塵機 MODEL NO.: GVC150RD A GILMAN GROUP BRAND...
  • Page 2 Please read and retain for future reference. saFETY INsTRuCTION - GENERaL • Use this appliance solely in accordance with these instructions. • This appliance is for household use only, not for commercial purpose. • Remove all packaging material from the appliance before use. •...
  • Page 3 saFETY INsTRuCTION - DuRING OPERaTION • Make sure your hands are dry before touching the appliance, power cord or plug. • Do not pick up the appliance if it falls into water. Remove the plug from the socket immediately. Do not use the appliance again. •...
  • Page 4: Product Overview

    PRODuCT OVERVIEw 1. Handle 10. Dust container cover 2. Main Unit 11. Filter 3. Speed mode button 12. Stainless Steel filter cover 4. Battery level and charging indicator 13. Wall hanger 5. Dust container 14. 2-in-1 crevice tool 6. Aluminium tube 15. Narrow nozzle 7. LED floor brush 16. BS plug 8. Air outlet 17. Motorized bed brush 9. Dust container releasing button...
  • Page 5 ChaRGING Before using your vacuum cleaner for the first time, allow the battery to charge for approx. 4 - 5 hours. Important note: Please note the vacuum cleaner can not start operation during charging • When the vacuum cleaner is in use, the indicator light can display the battery power status in real time.
  • Page 6 assemble and Dis-assemble the LED floor brush / aluminium tube • Assemble: Insert the end of the LED floor brush into the tube, after hearing the click sound, then LED floor brush installed in place. • Dis-assemble: Use one hand to hold the LED floor brush, press the release button on the tube and remove the LED floor brush outwards.
  • Page 7: Cleaning And Storage

    aCCEssORIEs 2-in-1 Crevice tool / narrow nozzle assemble with handheld unit • A: A crevice tool with a narrow nozzle, which you can use to clean window frames and crevices, etc. • B: Push unwards the cleaning brush of 2-in-1 crevice tool, you can use to clean delicate or irregular surfaces, furniture, venetian blinds,etc.
  • Page 8 Cleaning or replacing the filter The filters can become blocked after some time and can thereby reduce the suction power. It is therefore important that the above mentioned filter deter- mine to replace. • Take out the filter and filter cover, remove the dust container from the ma- chine, then take out the filter assembly, after that rotate the filter cover coun- terclockwise to remove it from the assembly, and then rotate the filter coun- terclockwise to remove it.
  • Page 9 • Remove the hairs or dust around the roll brush, rinse the roll brush with water gently, let it air-dry completely before reassemble. • After cleaned, install the rolling brush inside the motorized floor brush. Make sure the rolling brush is proper seat in position. Slide the sliding switch to lock position. Clean the motorized bed brush •...
  • Page 10 storage with wall mount hanger • After cleaning, you can store your appliance on the wall mount hanger. Position the wall mount hanger against the wall and mark the points at which the fasten- ing screws are to be inserted. Using a drill, drill the holes for the screws, insert the plastic anchor provided, then hang the wall mount hanger on the screws, and tighten the screws up to their full extent.
  • Page 11: Troubleshooting

    TROubLEshOOTING Warning: Please turn off the vacuum cleaner before maintenance, othecr- wise it may cause electric shock or other personal injury. PROBLEM POSSiBLE cAUSES SOLUTiON Vacuum cleaner does not 1. The battery is exhausted 1. Charge the battery accord- 2. The used charger is not ingly to he instructions original.
  • Page 12: Product Specifications

    PRODuCT sPECIFICaTIONs Model no.: GVC150RD Voltage: DC 22.2V Output power: 150W Main unit 15W LED floor brush 12W Motorized bed brush Charging time: Approx. 4 - 5 hours Two Speed of run time: About 17 mins (High) / 30 mins (Low)
  • Page 13 閱讀下列說明事項並請妥善保管,以供日後參考。 安全指引 - 一般安全 - 請按照這些說明事項, 使用本產品。 - 本產品僅供家用,不作商業用途。 - 使用前,請將所有包裝材料拆除。 - 0至8歲的兒童不應使用本產品。 - 超過8歲的兒童可使用本產品,但請勿由肢體不健全、感覺或精神上有障礙或 缺乏相關經驗和知識的人使用,除非有負責他們安全的人對他們使用本產品進 行監督或指導。 - 請務必看顧好兒童,以確保他們不玩耍本產品。 - 兒童不應清潔或維修本產品。 - 當需進行任何維修,必須由專業維修人員進行維修。永遠不要嘗試自己修理本 產品。 - 手濕時不可以接觸電源插頭或本機。 - 主機不可以浸入水中。 - 兒童不可以把玩本機。 - 本機開著後不可以無人監管。 - 當本機開著時,頭髮、鬆身衣物、手指和身體其他部份都要離開本機。 - 只使用隨機附送的配件。 安全指引 - 電子和熱能產品 - 使用相符的電源和電壓,以防止觸電。 - 本產品只能使用帶接地線的電源插座。...
  • Page 14 安全指引 - 操作期間 - 請勿用潮濕的手插拔電源插頭或接觸本產品。 - 如果本產品落入水中,立即從插槽中拔下插頭,並且不要再次使用本產品。 - 切勿將本產品、電源線或插頭浸入水中或其他液體中。 - 使用後徹底清潔本產品 (請參閱“清潔和保養”) - 不可吸入任何可能產生泡沫的洗滌劑或水溶液。 - 產品運作時,不可拆卸本產品。 - 確保塵網組件安裝好,才可使用本產品,否則可能造成損壞。 - 吸入口與通風口不得遮蓋或堵塞。不可阻塞所有開口,開口被阻塞時不可使用。 - 不可使用本產品吸入任何正在燃燒/燃點的物品,如燃點的香煙或煙灰。不可吸 入任何爆炸性 物質、易燃性物品、可燃性液體、高溫物品、毒性物質、有機溶 劑、腐蝕性或強酸性物質。 - 不可吸入如玻璃碎片、釘子、石頭、針頭或刀片等邊緣銳利的物品。以免過濾器 受損。 - 不可使用碗碟機清洗本產品的組件。 - 本產品運作時,請勿觸摸旋轉刷的任何部分,否則可能造成機械損壞。 - 請勿吸水或其他液體,尤其是地毯清潔液,內部濕氣或水可能導致電器短路。 - 請勿吸入雷射印表機、影印機內部使用的碳粉、色粉等,否則可能導致火災或爆 炸。 - 不要吸入大量石膏、水泥和大片紙片等,這些物體可能會堵塞過濾器,必須及時 清理。 - 本產品無法吸取電池上的碳粉、鉛粉,不能在危險場所或工業生產場所使用,以...
  • Page 15 部件示意圖 1. 手柄 10. 塵箱蓋 2. 主機 11. 過濾網 3. 高/低速模式按鈕 12. 不鏽鋼過濾網 4. 電池量及充電顯示燈 13. 掛架 5. 塵箱 14. 2合1伸縮縫隙吸咀 6. 鋁管 15. 扁吸咀 7. 電動連LED探測燈地扒 16. 火牛 8. 出風口 17. 電動床刷 9. 塵箱釋放按鈕...
  • Page 16 充電 在第一次使用吸塵機前,先把電池充電約 4 - 5小時。 注意:吸塵機在充電時不能正常工作。 - 吸塵器使用時,指示燈可即時顯示電池電量狀態。 當最後一個燈開始閃爍時,表示吸塵器電量不足。 - 吸塵器配有專用火牛,接通電源後,充電指示燈會 循環亮起,表示吸塵器正在充電。當三個指示燈亮 起時,電池電量已充滿電。 安裝及使用說明 警告:電動刷含有滾動部件!為了避免人身傷害,吸塵器運轉時請勿觸摸滾刷, 如觸摸旋轉的滾輪可能會導致割傷、受傷或其他傷害,進行吸塵器維護時,請先 關閉機器,如果兒童於附近請注意安全。 充滿電後,長按電源開關按鈕 “ ” 開始工作,吸塵器開始時會在低速下工作, 再短按一次按鈕可切換為高速。再按一次即可停止操作。(低-高-停止,依次循環) 安裝和拆卸鋁管 安裝方法:將鋁管的末端插入主 釋放按鈕 機,聽到“嚓”一聲後,鋁管便是 安裝到位。 拆卸方法:一隻手按著鋁管釋放按 鈕,另一只手握著鋁管並將其移 開,然後把鈻鋁管卸下。...
  • Page 17 安裝和拆卸電動連LED探測燈地扒 / 鋁管 安裝方法:將鋁管的首端插入地扒,聽到“咔嚓”一聲後,電動連LED探測燈 地扒便是安裝到位。 拆卸方法:一隻手按著鋁管釋放按鈕,另一只手握著電動連LED探測燈地扒, 然後將電動連LED探測燈地扒卸下。 釋放按鈕 釋放按鈕 電動連LED探測燈地扒 / 電動床刷和主機連接 安裝方法:將電動連LED探測燈地扒 / 電動床刷插入主機,聽到“咔嚓”一聲 後,電動連LED探測燈地扒 / 電動床刷便是安裝到位。 拆卸方法:一隻手按著主機釋放按鈕,另一只手握著電動連LED探測燈地扒 / 電 動床刷,然後把電動連LED探測燈地扒 / 電動床刷卸下。 釋放按鈕 釋放按鈕...
  • Page 18 配件 2合1伸縮縫隙吸咀 / 扁吸咀和主機連接 A:扁吸咀 - 用於清潔的地方,如窗框和縫隙等。 B:除塵毛刷 - 按下2合1伸縮縫隙吸咀釋放按鈕,再推出除塵毛刷,用於清潔凹 凸及柔軟的表面,如傢俱、百葉窗簾等。 釋放按鈕 釋放按鈕 清潔和保養 清理塵箱 - 在清洗任何部件之前,確保吸塵機已關上。 - 按下塵箱前方的釋放按鈕,把塵箱及主機分離。 - 把塵箱內的垃圾清理。 - 如需要,可用乾淨水輕輕地沖走灰塵,待塵箱過濾器及過濾網完全清潔及完全 風乾才裝回本機。 注意:過濾網可能在一段時間後被堵塞,而減弱吸力。因此,過濾網更換是很重 要的。...
  • Page 19 高效能過濾網 - 過濾網可能在一段時間後被堵塞, 而減弱吸力。因此,過濾網更換是很重要的。 取出過濾器和過濾器蓋,從機器上拆下塵箱,然後取出過濾器組件,然後逆時 針旋轉過濾器蓋將其從組件上取下,然後逆時針旋轉過濾器將其取出。 注意:塵杯及所有過濾網不完全風乾,剩餘的水分可能進入吸塵機內部,對吸塵 機電路裝置造成損壞, 影響吸力效果及使機器內部部件傳出異味。 提醒:請勿放置過濾器,過濾器蓋在潮濕的地方。清洗後的過濾器應自然風乾。 請勿用風筒加速吹乾,可能會損壞過濾器並縮短其使用壽命。 清潔電動連LED探測燈地扒 電動連LED探測燈地扒可能會被大的物體阻擋,或者被頭髮或長線環繞。需要及 時清理滾刷。 - 按下地刷底部的滾刷釋放鈕並向後撥動,鎖扣會自動彈起。...
  • Page 20 - 把所有毛髮及污塵清走,用乾淨水輕輕地沖走滾刷上的灰塵,待完全清潔及完 全風乾才裝回電動地扒。 - 清理完畢後,需風乾再將滾刷安裝在電動地扒內。確保滾刷是裝回位置。將滑 動開/關鎖推回鎖定位置。 清潔電動床刷 - 電動地耙可能會被大的物體阻擋,或者被頭髮或長線環繞。需要及時清理滾刷。 - 將滑動開/關鎖推至開鎖位置,同時把側蓋向後推,把在地刷內的滾刷取出。 - 把所有毛髮及污塵清走,用乾淨水輕輕地沖走滾刷上的灰塵,待完全清潔及 完全風乾才裝回電動地耙。 - 清理完畢後,需風乾再將滾刷安裝在電動地耙內。滾刷未端對準側蓋內扣位, 確保滾刷是裝回位置,連同側蓋推回鎖定位置。 滾刷 側蓋 滑動開/關鎖 注意:所有配件必須風乾完成後,才裝回機身。...
  • Page 21 掛牆式或直立式站立以便儲藏 清潔後,可將本產品存放在牆掛支架上。將掛牆支架靠在牆壁上並標記要插入緊 固螺絲釘的位置。使用鑽頭鑽出螺釘孔,插入提供的膠塞,然後將掛牆支架釘在 螺釘上,並將螺釘擰緊。...
  • Page 22 疑難排解 警告:維護前請關閉吸塵器,否則可能導致觸電或其他人身傷害。 問題 可能原因 解決方法 吸塵器不運作 1. 電池電量耗盡 1. 依照指示為電池充電; 2. 不是原廠的的充電器。 2. 確保充電器與您使用的 型號相匹配 機器發出異聲 塵杯內裝滿垃圾,或風道 取出集塵杯,清理垃圾 堵塞 或堵塞物 吸力減弱 1. 塵杯已滿 1. 清潔塵杯 2. 過濾器需要清洗 2. 依照說明書上的指示清 3. 需要更換新濾芯 潔過濾器 4. 與手持式吸塵器的連接 3. 聯絡客服購買替換過 管、縫隙吸嘴或其他配 濾器 件未安裝到位 4. 依照指示重新安裝 5.
  • Page 23 產品規格 型號: GVC150RD 電壓 : DC 22.2V 功率: 150瓦 主機 15瓦 電動連LED探測燈地扒 12瓦 電動床刷 充電時間: 約 4 - 5小時 電池使用時間: 約 17分鐘 (高速) / 30分鐘 (低速) 產品尺寸(豪米): 直立式吸塵機連地耙: 1060(高) x 235(闊) x 160(深) 毫米 * 相關產品的規格,可能會因配件批次或實際使用地區的電壓差異而有所不同。...

Table of Contents