Advertisement
Advertisement
Table of Contents
Related Manuals for Franke FDF PRO 9354 XS AU
Summary of Contents for Franke FDF PRO 9354 XS AU
- Page 1 Instructions for use and installation Cooker Hood FDF PRO 9354 XS AU...
-
Page 2: Table Of Contents
INDEX SAFETY INFORMATION................................. 3 CHARACTERISTICS ................................6 INSTALLATION..................................7 USE ...................................... 10 CARE AND CLEANING................................. 11... -
Page 3: Safety Information
SAFETY INFORMATION For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. The wire connection has to be done by specialized technician. - Page 4 If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
- Page 5 Accessible parts may become hot when used with cooking appliances. Clean and/or replace the Filters after the specified time period (Fire hazard). See paragraph Care and Cleaning. There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
-
Page 6: Characteristics
CHARACTERISTICS Dimensions 598-698-798-898-1198 Min. Min. 650mm 650mm Components Ref. Q.ty Product Components Hood Body, complete with: Controls, Light, Blower, Filters Telescopic Chimney comprising: Upper Section Lower Section Reducer Flange ø 150-120 mm Air Outlet Connection Ref. Q.ty Installation Components Upper Chimney Section Fixing Brackets 7.2.1 Wall Plugs Screws 4,2 x 44,4... -
Page 7: Installation
INSTALLATION Wall drilling and bracket fixing 7.2.1 Wall marking: • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. •... - Page 8 Mounting the hood body • Before attaching the hood body, tighten the two screws Vr lo- cated on the hood body mounting points. • Hook the hood body onto the screws 12a. • Fully tighten the support screws 12a. • Adjust the screws Vr to level the hood body. Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the...
-
Page 9: Electrical Connection
ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. • Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is cor- rectly inserted in the socket placed on the side of the fan. -
Page 10: Use
Control panel Button Function Turns the Motor off. When the filters alarm is triggered, the alarm can be reset by pressing and All the Leds holding this button for approximately 5 seconds. These indications are only flash 3 visible when the motor is turned off. times. -
Page 11: Care And Cleaning
CARE AND CLEANING Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS • The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. • Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. - Page 12 Franke S.p.a. Via Pignolini,2 37019 Peschiera del Garda (VR) www.franke.it 991.0579.226_03 - 211018 - D000000005718_02...
Need help?
Do you have a question about the FDF PRO 9354 XS AU and is the answer not in the manual?
Questions and answers