Kidde 2X-AF1-S Installation Manual
Hide thumbs Also See for 2X-AF1-S:
Table of Contents

Advertisement

Quick Links

2X-A Series Installation
Manual
P/N 00-3280-501-4003-02 • ISS 07NOV23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2X-AF1-S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kidde 2X-AF1-S

  • Page 1 2X-A Series Installation Manual P/N 00-3280-501-4003-02 • ISS 07NOV23...
  • Page 2 Copyright © 2023 Carrier. All rights reserved. Trademarks and 2X-A Series is a trademark of Carrier. patents Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. Manufacturer Carrier Manufacturing Poland Spółka Z o.o.
  • Page 3: Table Of Contents

    Content Important information ii Chapter 1 Introduction 1 Product range 2 Product compatibility 3 Product overview 4 Chapter 2 Installation 17 Electrical safety 18 Cabinet and PCB layout 19 Cabinet installation 22 Battery installation 28 Connections 31 Chapter 3 Configuration and commissioning 45 Introduction 46 Maintenance level operation and configuration 51 Installer level operation and configuration 68...
  • Page 4: Important Information

    Important information Introduction This is the installation manual for the 2X-A Series fire alarm, repeater, and evacuation control panels. Read these instructions and all related documentation entirely before installing or operating this product. Firmware compatibility Information in this document covers control panels with firmware version 5.0 or later.
  • Page 5: Product Warnings And Disclaimers

    Product warnings and disclaimers THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY QUALIFIED PROFESSIONALS. CARRIER FIRE & SECURITY B.V. CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED RESELLER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND SECURITY RELATED PRODUCTS.
  • Page 6: Product Symbols

    Product symbols The following symbols are used on the product. This symbol indicates that caution is necessary when operating or maintaining the device or control close to where the symbol is placed. This symbol indicates that the installation manual should be consulted when operating or maintaining the device or control close to where the symbol is placed.
  • Page 7: Introduction

    Chapter 1 Introduction Summary This chapter provides an introduction to your control panel, the main controls, and the indicators. Content Product range 2 Product compatibility 3 Product overview 4 The user interface 4 Front panel controls and indicators 7 LCD controls and indicators 12 Acoustic indicators 14 Conditions 15 2X-A Series Installation Manual...
  • Page 8: Product Range

    The complete range of control panels is shown in the following tables. Table 1: Small cabinet control panels with up to 4 A output Model Description 2X-AF1-S One-loop addressable fire alarm control panel 2X-AF1-FB-S One-loop addressable fire alarm control panel with fire routing and fire...
  • Page 9: Product Compatibility

    Chapter 1: Introduction Model Description 2X-AFR Addressable fire alarm repeater panel 2X-AFR-FB Addressable fire alarm repeater panel with fire routing and fire protection controls [1] Includes a fireman's key. Table 3: Large cabinet control panels with up to 10 A output (-P variants) Model Description 2X-AE2-P...
  • Page 10: Product Overview

    Chapter 1: Introduction Product overview This topic provides an introduction to the control panel user interface, LCD, operator controls, and indicators. For a detailed overview of front panel controls and indicators, see “Front panel controls and indicators” on page 7. The user interface Figure 1: Fire panel user interface (with fire routing and fire protection controls) Sounder Start/Stop Button and LED...
  • Page 11 Chapter 1: Introduction Figure 2: Evacuation panel user interface Supply LED Reset button and LED General Test LED Panel Silence button and LED General Disable LED Sounder Start/Stop Button and LED General Fault LED System Fault LED Alarm LED Low Battery LED 6.
  • Page 12 Chapter 1: Introduction Configuration options Depending on your configuration, the labels for some interface buttons may change. See Table 4 below. Table 4: Configured changes to interface buttons and LEDs Item EN 54 NEN 2575 All Output Groups Start/Stop All Evacuation Start/Stop Programmable output group start/stop Evacuation area sounders start/stop [1] Sounder Start/Stop...
  • Page 13: Front Panel Controls And Indicators

    Chapter 1: Introduction Front panel controls and indicators Operational features described in this section are not available to all users. More information on control panel operation and access restrictions can be found in the topic “User levels” on page 46. Common controls and indicators The table below includes information for the common controls and indicators available for fire, repeater, and evacuation panels.
  • Page 14 Chapter 1: Introduction Control/LED LED colour Description Fire Routing Yellow Indicates a fire routing fault, disablement, or test. Fault/Disabled/Test LED A flashing LED indicates a fault. A steady LED indicates a disablement or a test. Fire Protection Cancels a previously configured delay as it counts On/Acknowledged button down and activates fire protection.
  • Page 15 Chapter 1: Introduction Control/LED LED colour Description System Fault LED Yellow Indicates a control panel system failure or that one or more reported events (alarm, zone alarm, fault, condition, etc.) exceed the maximum limit of 512. See “System Fault LED indication – maximum limit for event type reporting”...
  • Page 16: Evacuation Panel Controls And Indicators

    Chapter 1: Introduction Evacuation panel controls and indicators The table below includes information for the additional controls and indicators for evacuation panels. Note: If the evacuation panel is operating in NEN 2575 mode, only sounder output groups can be associated with the programmable start/stop buttons. Table 6: Evacuation panel controls and indicators Control/LED LED colour...
  • Page 17 Chapter 1: Introduction Output group LED indications The control panel can be configured to have several sounder, fire routing, or fire protection output groups. Some groups may use the same indicators. When such groups have the same status, that status is indicated. In the case of conflicting status, the highest priority status is displayed.
  • Page 18: Lcd Controls And Indicators

    Chapter 1: Introduction LCD controls and indicators Figure 3: LCD controls and indicators 1. Day/night mode indicator 2. System date and time (and active fire routing delay or extended fire routing delay countdown) 3. Control panel network status (stand-alone, networked, repeater) 4.
  • Page 19 Chapter 1: Introduction Icons displayed on the LCD Icons displayed on the LCD are shown below. Table 7: LCD icons and descriptions Icon Description This icon indicates that the primary sensitivity mode Day mode (network) setting for control panels in the fire network is day mode.
  • Page 20: Acoustic Indicators

    Chapter 1: Introduction Icon Description This icon indicates a manual call point alarm (sprinkler). Manual call point alarm (sprinkler) [1] This icon indicates a manual call point alarm Manual call point alarm (“hausalarm”). This is a local alarm with no fire routing (“hausalarm”) [1] activation.
  • Page 21: Conditions

    Chapter 1: Introduction Conditions A summary of system events logged as conditions is shown below. Table 9: System events logged as conditions Condition type Description Alert A device is in alarm but the system is waiting for an additional alarm event to confirm the zone alarm Configuration device connected A control panel configuration session is initiated via an external device (PC, laptop, etc.)
  • Page 22 Chapter 1: Introduction The following system status events are also added to the event log (but are not included in the control panel current events report). Table 10: Other system status events added to the event log Event Description Actions An output group is activated or deactivated or a programmable system command is executed (via the Configuration Utility)
  • Page 23: Installation

    Chapter 2 Installation Summary This chapter provides detailed installation and connection information for your control panel. Caution: This product must be installed and maintained by qualified personnel adhering to the CEN/TS 54-14 standard (or the corresponding national standard) and any other applicable regulations. Content Electrical safety 18 Cabinet and PCB layout 19...
  • Page 24: Electrical Safety

    Chapter 2: Installation Electrical safety WARNING: Electrocution hazard. To avoid personal injury or death from electrocution, remove all sources of power and allow stored energy to discharge before installing or removing equipment. Caution: Equipment damage hazard. This product is sensitive to electrostatic discharge (ESD).
  • Page 25: Cabinet And Pcb Layout

    Chapter 2: Installation Cabinet and PCB layout Figure 4: Large cabinet and PCB layout (with 6 A power supply) 1. 24V connector 9. COM0 serial port and interface connector 2. COM2 serial port 10. COM1 serial port and interface connector 3.
  • Page 26 Chapter 2: Installation Figure 5: Large cabinet and PCB layout (with 10 A power supply) 1. 24V connector 11. Power supply connector 2. COM2 serial port 12. Power supply 3. Loop and fire system connectors 13. Battery fuse and battery selection jumper 4.
  • Page 27 Chapter 2: Installation Figure 6: Small cabinet and PCB layout 1. Loop and fire system connectors 8. COM1 serial port and interface connector 2. Spirit level 9. Battery connector 3. Earth studs 10. Power supply connector 4. Ethernet connector 11. Mains terminal block and fuse 5.
  • Page 28: Cabinet Installation

    Chapter 2: Installation Cabinet installation Where to install the control panel Install the control panel in a location that is free from construction dust and debris, and immune to extreme temperature ranges and humidity. See Chapter 5 “Technical specifications” on page 137 for more information on the operating temperature and relative humidity specifications.
  • Page 29: Fixing The Cabinet To The Wall

    Chapter 2: Installation Fixing the cabinet to the wall Fix the cabinet to the wall using five M4 × 30 screws and five Ø 6 mm wall plugs, as shown in Figure 8 below. Figure 8: Mounting hole locations To fix the cabinet to the wall: 1.
  • Page 30: Adding The Menu Inserts

    Chapter 2: Installation Adding the menu inserts Add the control panel interface menus as shown below. Figure 9: Adding the menu inserts The inserts are numbered 1 and 2F/2E, and are inserted at the locations indicated above (with the printed area facing the front of the control panel). For evacuation panels, remember to add descriptions to insert 2E for any output groups assigned to the programmable buttons.
  • Page 31: Connecting The User Interface Cable

    Chapter 2: Installation Connecting the user interface cable Connect the user interface cable as shown below. Figure 10: Connecting the user interface cable 2X-A Series Installation Manual...
  • Page 32: Connecting The Internal Printer And Loading Paper

    Chapter 2: Installation Connecting the internal printer and loading paper This topic shows you how to connect the internal printer and load the printer with paper. See “Printer configuration” on page 90 for printer configuration options. The internal printer is only available on selected models. Connecting the internal printer Connect the internal printer as shown below.
  • Page 33: Loading Paper

    Chapter 2: Installation Loading paper Load the paper for the internal printer as shown below. Figure 12: Loading the paper for the internal printer 2X-A Series Installation Manual...
  • Page 34: Battery Installation

    Chapter 2: Installation Battery installation Compatible batteries The control panel requires two 12 V, rechargeable, sealed lead-acid batteries. Use only the compatible batteries shown below. Caution: Not all compatible batteries can be used with all control panels. Some compatible batteries must be installed in an external battery box (not supplied). See “Installing batteries”...
  • Page 35 Chapter 2: Installation Battery type configuration Caution: This configuration applies to control panels with a 10 A PSU. No battery type configuration is required for control panels with a 4 A or 6 A PSU. To ensure the correct charging current, configure the battery type using the battery selection jumper located above the battery fuse on the PSU (see Figure 13 below).
  • Page 36: Installing Batteries

    Chapter 2: Installation Installing batteries The installation location for the batteries (internal or external) depends on the control panel cabinet size and the battery capacity, as shown in the table below. Table 13: Battery installation location Control panel 7.2 Ah 12 Ah 17/18 Ah 36/38 Ah...
  • Page 37: Connections

    Chapter 2: Installation Connections Recommended cables Recommended cables for optimal system performance are shown in the table below. Table 14: Recommended cables Cable Cable requirements Max. cable length Mains cable 3 × 1.5 mm Loop cable 0.13 to 3.31 mm² (26 to 12 AWG) shielded or 2 km [2] unshielded twisted-pair (52 Ω...
  • Page 38: Securing Cables

    Chapter 2: Installation To determine noise immunity, check the communications error rate and the stability of analogue values for installed devices. Securing cables Use 20 mm cable glands to ensure clean and secure connections. All cables should be fed through the cable guides in the cabinet housing to eliminate movement.
  • Page 39 Chapter 2: Installation Figure 15: Overview of EN 54-13 fire system connections with a single Class A loop 1. 2010-FS-EOL end-of-line device 2. Fault indicating equipment Earth connection: Connect one side to the earth studs in the control panel cabinet (not to the loop EARTH terminal), the other side can be left floating.
  • Page 40: Connecting Loops

    Chapter 2: Installation Connecting loops Loop guidelines For best results, follow these guidelines when connecting loops: • Install at least one isolator per loop (we recommend one for every 32 devices). Always review your isolator/device installation sheet for detailed installation requirements or limitations. •...
  • Page 41: Class B Loop Connection

    Chapter 2: Installation Class B loop connection Caution: Class B loops do not comply with EN 54-13 requirements. Never install more than 32 devices on a Class B loop. Connect Class B loops as shown in Figure 16 below. Connection may be made to either the A connectors (as shown) or to the B connectors, but not to both.
  • Page 42: Connecting Loop Devices

    Chapter 2: Installation Connecting loop devices Each loop can support up to 128 devices. For detailed loop device installation information, see your device installation sheet. Connecting inputs Input functionality Each control panel has two supervised inputs, marked INPUT1 and INPUT2. For input configuration, see “Field configuration”...
  • Page 43: Connecting Outputs

    Chapter 2: Installation Connecting outputs Control panel outputs are shown in the table below. Table 16: Control panel outputs Output Description Supervision 24V AUX Used to supply power to auxiliary equipment. The Short circuit, voltage output can be configured as resettable and to shut level down when there is no mains power.
  • Page 44 Chapter 2: Installation End-of-line components for outputs are included in the accessory kit provided with your control panel. Note: Output termination differs for typical and EN 54-13 installation types. Take care to install the correct termination for your installation. Output polarity All outputs are polarity sensitive.
  • Page 45: Connecting The Mains Power Supply

    Chapter 2: Installation Connecting the mains power supply Caution: Connect the mains power supply before connecting the batteries. The control panel can be operated at 110 VAC 50/60 Hz or 240 VAC 50/60 Hz (+10%/−15%). WARNING: For large cabinet control panels with a 6 A power supply, the power setting must be changed manually (see “Selecting 115 or 230 VAC operation for 6 A power supplies”...
  • Page 46: Connecting The Batteries

    Chapter 2: Installation Selecting 115 or 230 VAC operation for 6 A power supplies Caution: An incorrect power setting can damage the power supply. Always disconnect the control panel from the mains supply before changing the power setting. The default power setting is 230 VAC. For 115 VAC operation use a small screwdriver to change the power setting switch, located on the side of the power supply unit, as shown in Figure 18 below.
  • Page 47: Connecting Expansion Boards

    Chapter 2: Installation Connecting expansion boards Caution: Always disconnect the control panel from the mains power supply before installing an expansion board. See your expansion board installation sheet for detailed installation information. Connecting a fire network Note: See your network board installation sheet for detailed installation and connection information.
  • Page 48: Ring Configuration

    Chapter 2: Installation Ring configuration Ring network configuration is recommended as it provides for redundancy in the transmission path. For ring configuration (Class A), use both ports to connect all network boards or control panels to form a ring, as shown below. Figure 20: Fire network ring configuration Bus configuration Caution:...
  • Page 49: Connecting An External Printer Or Ascii Terminal

    Chapter 2: Installation Connecting an external printer or ASCII terminal To print control panel events in real time, connect an external EPSON LX300 printer or ASCII terminal to COM0. Only one external printer can be connected. Note: This option requires the 2010-2-232-KIT (not supplied). The kit contains a 3 m cable and the 2010-2-232-IB isolation board required for external RS-232 device connections.
  • Page 50 Chapter 2: Installation 2X-A Series Installation Manual...
  • Page 51: Configuration And Commissioning

    Chapter 3 Configuration and commissioning Summary This chapter provides configuration and commissioning information for your control panel and fire detection system. Content Introduction 46 Expansion board User levels 46 configuration 86 Configuration overview 48 Load auxiliary files 87 Maintenance level operation and System update 89 configuration 51 Printer configuration 90...
  • Page 52: Introduction

    Introduction User levels Access to some of the features of this product is restricted by the user level assigned to a user account. Caution: Always change default passwords. When a default password is not changed, the control panel registers a condition and displays a notification until the default password is changed.
  • Page 53 Chapter 3: Configuration and commissioning Restricted user levels Restricted user levels are protected by password security. You are required to enter the username and password assigned to you. The control panel automatically exits from a restricted user level and reverts to the public user level after a few minutes if no button is pressed.
  • Page 54: Configuration Overview

    Chapter 3: Configuration and commissioning Configuration overview WARNING: The installer/maintenance contractor is responsible for ensuring that the fire system configuration is performed in a competent and workmanlike manner consistent with applicable local standards. Carrier makes no representations or warranties of any kind with respect to installation and/or maintenance where this product is used to create a non-compliant system configuration.
  • Page 55: Control Panel Configuration Recommendations

    Chapter 3: Configuration and commissioning Control panel configuration recommendations Use the control panel configuration wizards to guide you through the configuration process for most applications. To access the configuration wizards press F1 (Wizards) from the installer level Main menu. In general we recommend the following configuration order: 1.
  • Page 56: Configuration Options

    Chapter 3: Configuration and commissioning Configuration options The options listed below are available when making configuration changes to the control panel. The control panel configuration (and configuration revision) is only updated when configuration changes are applied by pressing F3 (Apply). The configuration revision change and timestamp are recorded in the Revision report and can be accessed at operator, maintenance, and installer levels.
  • Page 57: Maintenance Level Operation And Configuration

    Chapter 3: Configuration and commissioning Maintenance level operation and configuration The maintenance level is password-protected and is reserved for authorized users trained to operate the control panel and perform routine maintenance tasks for the fire system. The default password for the default maintenance user is 3333.
  • Page 58: The Field Setup Menu

    Chapter 3: Configuration and commissioning The Field setup menu Use the Field setup menu to set timeout values for zone test and disablement operations. Zone test and disablement timeout Note: This feature is not compliant with EN 54-2. Use the Test/Disable t_out menu to set an independent timeout value (in minutes) for zone test and disablement operations for the local control panel.
  • Page 59: The Panel Setup Menu

    Chapter 3: Configuration and commissioning The Panel setup menu Use the Panel setup menu to set the date and time, to synchronize the date and time in a fire network, and to set day or night mode sensitivity settings. Date and time Select Date and time to change the control panel date and time.
  • Page 60 Chapter 3: Configuration and commissioning Setting the day/night schedule Select Day/Night schedule to configure weekly schedules for day and night mode settings. To set a day/night schedule: 1. Select Panel setup from the Main menu. 2. Select Day/Night mode, and then select Day/Night schedule. 3.
  • Page 61 Chapter 3: Configuration and commissioning 6. Enter any additional holiday periods as described in steps 3 and 4. 7. Press F4 (Enter), and then press F1 (Back). 8. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. Additional day/night mode settings Select Day/Night setup to configure additional settings such as manual override of day/night mode schedule and holiday calendar mode changes or delay...
  • Page 62 Chapter 3: Configuration and commissioning Notes on day and night mode settings Day/night mode may be configured to change with a remote input. Depending on the installation settings, the system may be configured to use an external input to override the day/night mode setting until the following programmed change (if any).
  • Page 63: The Communications Menu

    Chapter 3: Configuration and commissioning The Communications menu Use the Communications menu to set up email accounts for event notifications and to safely remove a USB device connected to the control panel. Managing email accounts Select Email accounts to manage the email accounts for remote monitoring and to configure the notifications sent to each email address.
  • Page 64: The Disable/Enable Menu

    Chapter 3: Configuration and commissioning The Disable/Enable menu Use the Disable/Enable menu to disable and enable the system features and devices. Disabled features and devices do not indicate faults or fire alarms. Note: Changes to disable/enable configuration at this user level are not stored in the control panel configuration and are not included in any saved configuration files.
  • Page 65: The Test Menu

    Chapter 3: Configuration and commissioning The Test menu Use the Test menu to test system features or devices. The following features or devices can be tested from this menu: • Zones • Control panel input activation • Control panel and loop output activation •...
  • Page 66 Chapter 3: Configuration and commissioning When there is a fire alarm in any zone that is not in test, the control panel responds to the alarm event as configured. Testing control panel input activation To test activation of an input: 1.
  • Page 67: Locating Devices

    Chapter 3: Configuration and commissioning Locating devices Select Locate device to activate a loop device LED. This helps to identify the location of a device in the installation. You will need the Firenet ID of any remote device LED to be activated. To locate a device: 1.
  • Page 68 Chapter 3: Configuration and commissioning Activating service mode Select Activate service mode to avoid accidental activation or deactivation of outputs or output groups (local or remote) during tests. In this mode the control panel indicates and logs activation events as configured but does not activate or deactivate the corresponding output.
  • Page 69: The Reports Menu

    Chapter 3: Configuration and commissioning The Reports menu Use the Reports menu to view, clear, or back up the event log and to display a variety of system status reports. The reports available to maintenance users are shown in the table below. Table 24: Reports available to maintenance users Report Description...
  • Page 70 Chapter 3: Configuration and commissioning Viewing or clearing the event log Select View all or Clear to view or clear alarm, fault, and condition events logged by the control panel. To view or clear the event log: 1. Select Reports from the Main menu. 2.
  • Page 71: Saving Reports

    Chapter 3: Configuration and commissioning Figure 23: USB connectors on the control panel PCB 1. USB connectors Saving reports Select Save report to save a report. Reports are saved to a USB flash drive (not supplied) in XML format and can be viewed with the Configuration Utility PC application.
  • Page 72: The Password Setup Menu

    Chapter 3: Configuration and commissioning The Password setup menu Use the Password setup menu to change your maintenance password and to manage operator user accounts. Changing your password Caution: To avoid unauthorised access, always change default passwords. Select Change password to change your password. You cannot change passwords for other maintenance users.
  • Page 73 Chapter 3: Configuration and commissioning To delete an operator user account: 1. Select Password setup from the Main menu, and then select Manage users. A list of the user accounts that you have permission to edit is displayed. 2. Select the user account you want to delete. You cannot delete the default operator user account.
  • Page 74: Installer Level Operation And Configuration

    Chapter 3: Configuration and commissioning Installer level operation and configuration The installer level is password-protected and is reserved for authorized users installing and configuring the control panel and the fire system. The default password for the default installer user is 4444. The Main menu The installer level Main menu is shown below.
  • Page 75: Id Configuration

    Chapter 3: Configuration and commissioning Option Description Load auxiliary files Loads auxiliary files from a USB flash drive. Auxiliary files that can be loaded include custom standby and alarm screens, and updated language or font files for extended language support. System update Loads control panel firmware updates.
  • Page 76: Regional Options

    Chapter 3: Configuration and commissioning Regional options Select Regional options to set the regional operating mode. Available options are shown in the table below. Table 26: Regional operating modes Operating mode Region EN 54-2 (default) European Union EN 54-2 Evacuation European Union (Spain) NBN S 21-100 [1] European Union (Belgium)
  • Page 77: Firenet Configuration

    Chapter 3: Configuration and commissioning Firenet configuration Select Firenet to configure the control panel fire network and repeater settings shown in the table below. Table 27: Firenet configuration options Option Description Firenet map Displays all detected control panels, to add control panels to the fire network, or to remove control panels from the network.
  • Page 78 Chapter 3: Configuration and commissioning Firenet opmode Available network operation modes are shown below. Table 28: Firenet operation modes Mode Description Stand-alone Configures a stand-alone control panel. This is the default setting for fire alarm control panels. Networked Configures a networked control panel. See description below. Repeater Configures a networked repeater.
  • Page 79: Global Controls

    Chapter 3: Configuration and commissioning Repeater map The default setting is YES (all control panels in the fire network are repeated). To change the repeater map settings: 1. Select Panel setup from the Main menu. 2. Select Firenet, and then select Repeater map. 3.
  • Page 80 Chapter 3: Configuration and commissioning Command filter Select Command filter to configure the types of commands sent to the fire network in control panels with the corresponding global controls configured. The commands that can be configured are shown in the table below. Table 29: Command filter configuration options Command Description...
  • Page 81 Chapter 3: Configuration and commissioning Class B Select Class B to configure your fire network class configuration (Class A or Class B). The default setting is NO (Class A network configuration). To change the network class settings: 1. Select Panel setup from the Main menu. 2.
  • Page 82: Communications Configuration

    Chapter 3: Configuration and commissioning Communications configuration TCP/IP Select TCP/IP to configure TCP/IP settings. The default TCP/IP settings are shown in the table below. The control panel MAC address and Host information are also available in this screen if required for troubleshooting purposes. Note: For increased security, we recommend against using Ethernet for remote connection to the control panel via the Internet.
  • Page 83: Email Accounts

    Chapter 3: Configuration and commissioning Email accounts Select Email accounts to manage the email accounts for remote monitoring and to configure the notifications sent to each email address. For correct operation, TCP/IP and email server details must be configured (see “Email server” below). Note: Maintenance users are also able to modify settings for this service.
  • Page 84 Chapter 3: Configuration and commissioning SNTP server Select SNTP server to configure the Simple Network Time Protocol (SNTP) server settings. SNTP is a networking protocol for clock synchronization. Note: Polling settings for the SNTP server must be enabled separately – see “Auto date and time”...
  • Page 85: Other Settings

    Chapter 3: Configuration and commissioning Other settings 24V auxiliary Select 24V AUX config to configure the 24V AUX output state during reset and when the control panel is running on battery power. The default setting for both options is NO (the 24V AUX output is not deactivated). To change the configuration: 1.
  • Page 86 Chapter 3: Configuration and commissioning Buzzer Select Buzzer to configure the control panel buzzer behaviour (on or off) during fire alarm, fault, condition, or external connection events. The default setting for all event types is YES (the buzzer activates). To change the configuration: 1.
  • Page 87: Pulse Activation

    Chapter 3: Configuration and commissioning Self-test Select Self-test to schedule a functional self-test for each loop device and to generate a daily report in devices that support this feature. By default self-test is not enabled. To change the configuration: 1. Select Panel setup from the Main menu. 2.
  • Page 88 Chapter 3: Configuration and commissioning VdS Settings Select VdS settings to configure the alarm display format (standard format or VdS 2540 format). • Alarms in the standard alarm display format are indicated by zone, loop, and device (for example, Z0001:D2.018, indicating an alarm in zone 1, loop 2, device 18).
  • Page 89 Chapter 3: Configuration and commissioning To change the configuration: 1. Select Panel setup from the Main menu. 2. Select Other settings, and then select PSU Supervision. 3. Select and check 10 A or Ext. Select and check 10 A to enable power supply supervision for large cabinet control panels with an internal 10 A power supply (-P variants).
  • Page 90: Load/Save Configuration

    Chapter 3: Configuration and commissioning Load/Save configuration Restoring the previous configuration Select Restore configuration to restore the previous system configuration. Caution: For large cabinet control panels with an internal 10 A power supply (-P variants), always confirm that the PSU supervision setting is 10 A after restoring the system configuration (see “PSU supervision”...
  • Page 91 Chapter 3: Configuration and commissioning To save a configuration to file: 1. Open the control panel door and insert the USB flash drive into either of the USB type A connectors (see “Cabinet and PCB layout” on page 19). Close the control panel door.
  • Page 92: Expansion Board Configuration

    Chapter 3: Configuration and commissioning Expansion board configuration Select Expansion boards to add an installed expansion board to the control panel configuration. Note: If the installed expansion board firmware is not compatible with the control panel, a warning message is displayed. The available expansion boards are shown in the table below.
  • Page 93: Load Auxiliary Files

    Chapter 3: Configuration and commissioning Load auxiliary files Select Load auxiliary files to load auxiliary files from a USB flash drive. Auxiliary files that can be loaded include custom standby and alarm screens, and updated language or font files provided by the manufacturer. Note: Use only FAT32 file system USB flash drives with a maximum capacity of 32 GB.
  • Page 94 Chapter 3: Configuration and commissioning Adding language files or fonts Select Languages or Language fonts to add language files or fonts provided by the manufacturer. To add language files or fonts: 1. Open the control panel door and insert the USB flash drive with the required files into either of the USB type A connectors (see “Cabinet and PCB layout”...
  • Page 95: System Update

    Chapter 3: Configuration and commissioning System update Caution: Updating the control panel firmware may delete the current installation configuration data. Always back up your configuration data before updating the control panel firmware. Select System update to load control panel firmware updates provided by the manufacturer.
  • Page 96: Printer Configuration

    Chapter 3: Configuration and commissioning Printer configuration Select Printer configuration to configure internal, external, or terminal printers, where available. Configuration options are shown in the table below. By default, all printer configuration options are disabled. Table 35: Printer configuration options Option Description Used...
  • Page 97: Dact Configuration

    Chapter 3: Configuration and commissioning DACT configuration Select DACT configuration to configure settings for an installed DACT expansion board. Configuration options are shown in the table below. Table 36: DACT configuration options Option Description General config Configures the DACT status (used or not used) and event reporting options Ethernet config Configures Ethernet settings for monitoring network communication...
  • Page 98: Ethernet Configuration

    Chapter 3: Configuration and commissioning Ethernet configuration Select Ethernet configuration to configure settings for monitoring network communication with the central monitoring station (CMS). Configuration options are shown in the table below. Table 38: Ethernet configuration options Option Description Default value Period Configures the heartbeat period (in seconds) Fails...
  • Page 99: Cms Configuration

    Chapter 3: Configuration and commissioning Table 40: Site configuration event types Option Description Configures alarm reporting Configures fault reporting Configures condition reporting Configures alarm and fault reporting Configures alarm, fault, and condition reporting Configures fault and condition reporting Configures alarm and condition reporting To change the configuration: 1.
  • Page 100: Pstn Configuration

    Chapter 3: Configuration and commissioning To change the configuration: 1. Select Panel setup from the Main menu. 2. Select DACT config, and then select CMS config. 3. Select the CMS to configure (1 to 7). 4. Configure all required settings. 5.
  • Page 101: Panel Activation Key

    Chapter 3: Configuration and commissioning Panel activation key Note: See your PAK registration guide for more details on how to register or unregister purchased PAKs. Select Panel Activ. Key to register or unregister panel activation keys (PAKs). PAKs are used to extend the default functionality of the control panel - increasing the network capability, enabling additional protocols, etc.
  • Page 102: Auto Date And Time

    Chapter 3: Configuration and commissioning Auto date and time Select Auto date and time to configure automated date and time settings. Configuration options are shown in the table below. Table 44: Auto date and time options Option Description Default value SNTP [1] Enables polling a configured SNTP server Disabled...
  • Page 103: Bms Configuration

    Chapter 3: Configuration and commissioning BMS Configuration Select BMS Config to configure building management protocol settings (BACnet, Modbus). By default neither protocol is enabled. Table 45: BMS configuration options Option Description Default value Protoc Configures the BMS protocol (NO, BACnet, or Modbus) InitPan [1] Configures the initial panel address when using...
  • Page 104: Field Configuration

    Chapter 3: Configuration and commissioning Field configuration Use the Field setup menu to access the field configuration options shown below. Table 46: Field configuration options Option Description Autosetup Automatically configures installed loop devices to their default settings and assigns a reference value for the loop current consumption (see “Loop current consumption reference value”...
  • Page 105 Chapter 3: Configuration and commissioning • Assign all extinguishing devices to the default extinguishing output group (output group number 801) Extinguishing output groups are only activated with a confirmed alarm. They are not activated by zone alarms and rules. • Assign all fire routing outputs (where available) to the default fire routing output group (output group number 971) •...
  • Page 106: Loop Device Configuration

    Chapter 3: Configuration and commissioning Loop device configuration Select Loop device configuration to manually stop or start power for a loop, to add devices to a loop, or to change the default configuration settings after autosetup. To manually stop or start power for a loop: 1.
  • Page 107: Zone Configuration

    Chapter 3: Configuration and commissioning Zone configuration Zone configuration options are shown in the table below. Table 47: Zone configuration options Option Description General config Configures the initial zone, the initial zone for a zone LED indicator (if an optional zone indicator board is installed), the maximum number of zones in test, and the number of global zones.
  • Page 108: Initial Zone

    Chapter 3: Configuration and commissioning Repeat as required for each device. If the zone number is outside the valid range determined by the corresponding initial zone and the number of loops of the control panel, the operation does not complete and an invalid zone number error is displayed on the LCD. General configuration Select General config to configure the initial zone, to configure the initial zone for a zone LED indicator (if an optional zone indicator board is installed), the...
  • Page 109: First Zone Indicator Led

    Chapter 3: Configuration and commissioning First zone indicator LED The first zone indicator LED defines the zone number for the first LED (top left) for an installed zone indicator board. The remaining zones for the corresponding control panel follow sequentially, as shown in Table 49 below. The initial zone range is as follows: •...
  • Page 110 Chapter 3: Configuration and commissioning Zone configuration Select Zone config to configure additional zone settings, such as the zone type (normal or confirmed with corresponding parameters), area, CIT and ACT delays, disabled or enabled, and operation mode. Default settings are shown in the table below.
  • Page 111: Zone Alarm Confirmation

    Chapter 3: Configuration and commissioning Note: If all the devices assigned to a zone are disabled, then the zone is considered to be disabled and is indicated accordingly on the control panel. Zone alarm confirmation Zone confirmation is an alarm coincidence configuration method designed to reduce nuisance alarms.
  • Page 112: Confirmation Inhibition Time (Cit) And Alert Cancellation Time (Act)

    Chapter 3: Configuration and commissioning Option Description aIMaZ The alarm is confirmed by a single manual call point and a single initiating device in the same local area irrespective of which device first reports the alarm event. dMaZ The alarm is confirmed by two different manual call points in the same local area irrespective of which device first reports the alarm event.
  • Page 113: Area Configuration

    Chapter 3: Configuration and commissioning Operating mode Description MHA [1] The zone only allows “hausalarm” manual call points (or inputs configured for “hausalarm” manual call point operation mode). Fire routing output groups are not activated in the event of an alarm in a zone operating in this mode.
  • Page 114: Panel I/O Configuration

    Chapter 3: Configuration and commissioning Panel I/O configuration Panel input configuration Configurable options for control panel inputs are shown below. Table 54: Configurable options for control panel inputs Option Description Type Configures the input operation mode Control Enables or disables an input Input types are shown in Table 55 below.
  • Page 115 Chapter 3: Configuration and commissioning Type Description Manual call point alarm. This input type can be used for connecting to aspirating detector Fire2 outputs. PREAL Prealarm (unlatched). This input type can be used for connecting to aspirating detector Action outputs. Activation resets the panel remotely.
  • Page 116 Chapter 3: Configuration and commissioning To enable or disable a control panel input: 1. Select Field setup from the Main menu. 2. Select Panel I/O configuration. 3. Select Panel inputs, and then select the corresponding input. 4. In the Control option, select ENB (enable), DIS (disable), DIS_D (disable in day mode), or DIS_N (disable in night mode).
  • Page 117 Chapter 3: Configuration and commissioning Table 57: Configurable output types Type Description SND (default) Select this option for a sounder output Select this option for a fire routing output Select this option for a fire protection output Select this option for program options (see below) EXTIN Select this option for an extinguishing output ALARM...
  • Page 118: Output Groups

    Chapter 3: Configuration and commissioning Output groups Select Output groups to configure the control panel output groups. Control panel outputs must be assigned to output groups for activation. An output group is a collection of outputs of the same type that activate and deactivate at the same time (they are commanded simultaneously).
  • Page 119 Chapter 3: Configuration and commissioning Configurable options for output groups are shown below. Table 59: Configurable options for output groups Option Description Group_n Configures the output group number Type Configures the output group type Control Enables or disables the output group [BLANK] Output description To configure a default output group:...
  • Page 120: Output Group Activation

    Chapter 3: Configuration and commissioning 7. Press F4 (Enter), and then press F1 (Back). 8. Press F1 (Save), F3 (Apply), F4 (Discard), or F2 (Exit). Remember to apply saved settings from the Main menu. Output group activation Output groups can be activated by any of the following: •...
  • Page 121 Chapter 3: Configuration and commissioning To configure delayed output group activation: 1. Select Field setup from the Main menu, and then select Output groups. 2. Select Confirmations, and then select the output group to configure. A list of the available output groups that allow alarm confirmation configuration is displayed.
  • Page 122 Chapter 3: Configuration and commissioning Assigning an output group to a programmable button Note: This option is not available for control panels in regional mode VdS 2540. For fire alarm control panels, one output group can be assigned to the programmable button and LED on the control panel interface for control and indication.
  • Page 123: Activation Configuration

    Chapter 3: Configuration and commissioning Activation configuration Select Activation configuration options to configure the activation delays for output groups, investigation times, and general sounders behaviour (sounder silencing and second stage usage). Note: This option is not available on repeater panels. Delay configuration options are shown in the table below.
  • Page 124 Chapter 3: Configuration and commissioning To configure the output group delay: 1. Select Field setup from the Main menu, and then select Activation configuration. 2. Select the output group type to configure (Sounder, Fire routing, etc.). 3. Select Group_n, and then select ALL (to configure common delay settings for all output groups of the type selected) or select the output group number (to configure custom delay settings for a single output group of the type selected).
  • Page 125 Chapter 3: Configuration and commissioning Notes • Global delay options only set the delays of the zones that are enabled to activate the sounder or fire routing group. For example, if sounders and fire routing activate for zone 1 with a delay of 10 seconds and for zone 5 with a delay of 2 minutes, when selecting this option, sounders and fire routing will activate with the same selected delay after alarms in zones 1 or 5 and will not activate for all the other zones.
  • Page 126 Chapter 3: Configuration and commissioning Outputs assigned to an output group (for example, output group 5 SND) are activated depending on alarms in the fire network and with the corresponding delays. For example, if we have a one-loop control panel with the initial zone set to 100 and we want to configure sounder output group number 5, the following can be configured with this option: •...
  • Page 127: Investigation Mode

    Chapter 3: Configuration and commissioning To configure general delays: 1. Select Field setup from the Main menu, and then select Activation configuration. 2. Select General delays. 3. Select Investigation mode, and then select the type of investigation mode required. See “Investigation mode” below for more information on this option. 4.
  • Page 128 Chapter 3: Configuration and commissioning Table 64: Regional investigation time modes Setting Description NO (default) No investigation mode is required. MAX_ACK_T Maximum acknowledgement time. The configured investigation time starts to count down when the control panel reports a detector alarm. If the alarm is acknowledged during the investigation time (by pressing the Panel Silence button), then any sounder or fire routing delays continue to be processed as configured.
  • Page 129: Investigation Time

    Chapter 3: Configuration and commissioning Investigation time Select Investigation time to configure the duration (in seconds) of the investigation time for the configured investigation mode. Minimum, maximum, and default values for each mode are shown in the table below. Table 65: Investigation time values per mode Investigation mode Minimum Maximum...
  • Page 130 Chapter 3: Configuration and commissioning There are three configurable time periods, as shown in the table below. Table 66: Warning time, warning delay, and delay Time period Description Warning time The time from when the alarm is reported until the sounders activate the evacuation tone (or the corresponding evacuation tone delay starts to count down) Warning delay [1]...
  • Page 131 Chapter 3: Configuration and commissioning Sounders silence disable time Note: This feature is not available for control panels operating in NBN S 21-100 or EN 54 Evacuation mode (any configured sounder silence disable times are ignored). To prevent the immediate silencing of sounders when an alarm is first reported, the Sounder Start/Stop button may be temporarily disabled for a preconfigured period of time when a configured sounder delay is counting down.
  • Page 132: Loop Class Configuration

    Chapter 3: Configuration and commissioning Loop Class configuration Select Loop Class to configure the installation loop Class (Class A or Class B). The default setting is Class A. To configure a loop as Class A or Class B: 1. Select Field setup in Main menu. 2.
  • Page 133: Remote Disable/Enable Configuration

    Chapter 3: Configuration and commissioning Remote disable/enable configuration Use the Disable/Enable menu to remotely disable and enable system features and devices in a fire network. Disabled features and devices do not indicate faults or fire alarms. If remotely disabling zones in alarm, you must reset the control panel associated with the zone in alarm to complete the operation.
  • Page 134: Tests

    Chapter 3: Configuration and commissioning Table 68: Remote disable/enable – configuring Channel data Channel Description Devices with only a single input or output (detectors, manual call points, sounders). This is the default setting. I1, I2, I3, I4 Inputs 1 to 4 for I/O modules. O1, O2, O3, O4 Outputs 1 to 4 for I/O modules.
  • Page 135: Individual Device Diagnostics

    Chapter 3: Configuration and commissioning Individual device diagnostics Individual device diagnostics options are shown in the table below. Where a polling mode is not supported by a device, the panel uses the default polling mode. Note: Detailed device diagnostics may be requested by your regional technical support office to help troubleshoot technical issues.
  • Page 136: Password Setup

    Chapter 3: Configuration and commissioning Password setup Use the Password setup menu to change your password and to manage user accounts (operator, maintenance, or installer). Changing your password Caution: To avoid unauthorised access, always change default passwords. Select Password setup to change your password. To change your password: 1.
  • Page 137 Chapter 3: Configuration and commissioning To delete a user account: 1. Select Password setup from the Main menu, and then select Manage users. A list of all user accounts is displayed. 2. Select the user account you want to delete. You cannot delete the default user accounts 3.
  • Page 138: Commissioning

    Chapter 3: Configuration and commissioning Commissioning After the control panel and corresponding devices are installed and configured, the system must be commissioned. Check the following: • That the fire system is designed, installed, and configured in accordance with all required regulations and standards •...
  • Page 139: Maintenance

    Chapter 4 Maintenance Summary This chapter includes information on fire alarm system and battery maintenance. Content Fire alarm system maintenance 134 Battery maintenance 135 2X-A Series Installation Manual...
  • Page 140: Fire Alarm System Maintenance

    Chapter 4: Maintenance Fire alarm system maintenance To ensure correct functioning of your control panel and fire alarm system, and compliance with all European regulations, the following maintenance checks should be followed. Caution: Ensure that fire routing (where configured) has been disabled or that the fire brigade has been notified of any planned fire alarm tests.
  • Page 141: Battery Maintenance

    Chapter 4: Maintenance Battery maintenance Battery test fault indications A flashing Supply Fault LED indicates a battery fault or a battery cable fault. Additional information for the fault is displayed on the LCD, as shown below. Table 72: Battery fault messages LCD message Description Battery high resistance FLT [1]...
  • Page 142: Battery Start-Up

    Chapter 4: Maintenance Battery start-up Note: This start-up option is not available for large cabinet control panels with a 10 A power supply. The battery start-up option may be required after replacing batteries after a low battery indication when mains power is not available. To power up the control panel from the batteries, press the battery start button on the control panel PCB (marked as BAT, see Figure 28 below).
  • Page 143: Technical Specifications

    Chapter 5 Technical specifications Summary This chapter provides technical specifications for your control panel. Content Loop specifications 138 Power supply specifications 139 Battery and battery charger specifications 140 LCD specifications 141 Communication port specifications 141 Fire network specifications 141 Input and output specifications 141 Internal printer specifications 144 Mechanical and environmental specifications 144 2X-A Series Installation Manual...
  • Page 144: Loop Specifications

    Chapter 5: Technical specifications Loop specifications Loop configuration Class A or Class B Loop protocol Kidde Excellence Isolators At least one isolator per loop (we recommend one isolator for every 32 devices) Number of loop devices 128 max. Electrical characteristics – maximum output...
  • Page 145: Power Supply Specifications

    Chapter 5: Technical specifications Power supply specifications Mains voltage 240/110 VAC +10% −15% Mains frequency 50/60 Hz ±5% Mains current 4 A power supply 1.2 A max. at 240 VAC 1.9 A max. at 110 VAC 6 A power supply 1.6 A max.
  • Page 146: Battery And Battery Charger Specifications

    Chapter 5: Technical specifications Minimum current (Imin) [4] 4 A power supply 400 mA at 24 VDC Two-loop control panel with 24-zone indicator board, network board, and DACT board installed. 6 A power supply 600 mA at 24 VDC Four-loop control panel with internal printer, loop board, 40-zone indicator board, network board, DACT board, and peripherals interface board...
  • Page 147: Lcd Specifications

    Chapter 5: Technical specifications LCD specifications Display type 240 x 128 dot graphic LCD (monochromatic) LCD dimensions (L x W) 83 x 44 mm (active area) Backlight type LED style Backlight colour White Communication port specifications Ethernet Ethernet 10/100BaseT port (10 Mbps) Note: For increased security, we recommend against using Ethernet for remote connection to the control panel via the...
  • Page 148 Chapter 5: Technical specifications Configurable inputs [1] Number of inputs 2 supervised inputs, end-of-line resistor 15 kΩ, 1/4 W Active value 60.2 Ω ≤ active value ≤ 8 kΩ (0.33 to 15 VDC) Standby value 10 kΩ ≤ value ≤ 20.2 kΩ (16.1 to 18.9 VDC) Short circuit values ≤...
  • Page 149 Chapter 5: Technical specifications Fire and fault outputs [1] Output voltage range in −6.1 to −13.7 VDC standby Output voltage range in 21 to 28 VDC activation Output voltage range in short Less than −6.1 VDC circuit [1] Depending on the current requirements, output cable length restrictions may apply – see “Calculating the maximum output current as a function of the cable length”...
  • Page 150: Internal Printer Specifications

    Chapter 5: Technical specifications Internal printer specifications Note: The internal printer is only available on selected models. Printing method Thermal Resolution 203 dpi (8 dots/mm) Printing speed >50 mm/s Columns 24/40 Paper width 58 mm Paper weight 55 to 70 g/m² Roll dimension Ø...
  • Page 151 Chapter 5: Technical specifications Figure 29: Large cabinet dimensions and views 2X-A Series Installation Manual...
  • Page 152 Chapter 5: Technical specifications Figure 30: Small cabinet dimensions and views 2X-A Series Installation Manual...
  • Page 153: Appendix A Default Configurations

    Appendix A Default configurations The following table shows the settings for the default configuration of your panel. Table 73: Default configurations Description Default setting Power supply operation 230 VAC Control panel ID Day/night mode Full day to day mode Control panel network operation Stand-alone Network global commands Network mask...
  • Page 154 Appendix A: Default configurations Description Default setting Autosetup zone Initial zone OpMode configured as Mixed All detectors, manual call points, and zone modules to the initial zone All sounders to output group 1 (sounders) All relay/non-supervised outputs to output group 301 (program) All extinguishing modules to output group 801 (extinguishing)
  • Page 155: Appendix Bpstn Country Codes

    Appendix B PSTN country codes Use the PSTN country codes in the table below when configuring DACT board settings. Table 74: PSTN country codes Country Code Country Code Country Code Algeria Guam Philippines Argentina Hong Kong Poland Armenia Hungary Polynesia Australia Iceland Portugal...
  • Page 156 Appendix B: PSTN country codes Country Code Country Code Country Code Dubai Martinique Ukraine Ecuador Mexico Egypt Moldova Uruguay El Salvador Morocco Estonia Netherlands Uzbekistan Finland New Zealand Venezuela France Nigeria Yemen Georgia Norway Zambia Germany Oman Serbia Ghana Pakistan Greece Paraguay Guadeloupe...
  • Page 157: Appendix C Menu Maps

    Appendix C Menu maps Fire alarm control panels Maintenance user level Menu level 1 Menu level 2 Menu level 3 Field Setup Zone configuration Test/Disable t_out Panel setup Date and time Day/Night mode Day/Night schedule Holiday calendar Day/Night setup Communications Email accounts Remove USB device Disable/Enable...
  • Page 158 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Reports Event log View all Clear Attention required Revision Firmware revision Configuration revision Serial numbers Contact details Zone status Zone mapping Device status Panel I/O status Output groups status Rules status Firenet status Save/Print reports...
  • Page 159: Installer User Level

    Appendix C: Menu maps Installer user level Menu level 1 Menu level 2 Menu level 3 Field setup Autosetup Loop device configuration Zone configuration General configuration Zone configuration Area configuration Test/Disable t_out Panel I/O configuration Panel inputs Panel outputs Output groups Group configuration Confirmations Programmable controls...
  • Page 160 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Communications TCP/IP Email accounts Email server Remove USB device SNTP server Other settings 24V aux. configuration Fault notifications Buzzer Re-sound sounders Self-test configuration Pulse activation VdS settings PSU supervision Det dirty warning Cond notifications...
  • Page 161 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Disable/Enable Zones Devices Panel outputs Panel inputs Output groups Remote disable Test Zone test Output test Panel outputs Loop outputs Output group test Locate device Service mode Remote test Diagnostics Individual device...
  • Page 162: Fire Alarm Repeater Panels

    Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Save/Print reports Current events Event log Attention required Zone status Device status Panel I/O status Output groups status Rules status Firenet status PAK list Alarm counter Password setup Change password Manage users Secure access...
  • Page 163 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Reports Event log View all Clear Attention required Revision Firmware revision Configuration revision Serial numbers Contact details Panel I/O status Rules status Firenet status Save/Print reports Current events Event log Attention required Panel I/O status...
  • Page 164 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Firenet Firenet map Firenet opmode Repeater map Global controls Event filter Command filter Class B Communications TCP/IP Email accounts Email server Remove USB device SNTP server Other settings 24V aux.
  • Page 165 Appendix C: Menu maps Menu level 1 Menu level 2 Menu level 3 Test Output test Panel outputs Output group test Locate device Service mode Remote test Diagnostics Outputs current Power supply Loop current UI test Indicators test Keyboard test LCD test Battery test Reports...
  • Page 166 Appendix C: Menu maps 2X-A Series Installation Manual...
  • Page 167: Appendix D Regulatory Information

    Appendix D Regulatory information European standards for fire control and indicating equipment These control panels have been designed in accordance with European EN 54-2, and EN 54-4 standards. In addition, they comply with the following EN 54-2 optional requirements. Table 75: EN 54-2 optional requirements Option Description Output to fire alarm devices [1]...
  • Page 168 Appendix D: Regulatory information Regulations for construction products This section provides a summary on the declared performance according to the Construction Products Regulation (EU) 305/2011 and Delegated Regulations (EU) 157/2014 and (EU) 574/2014. For detailed information, see the product Declaration of Performance (available at firesecurityproducts.com).
  • Page 169 Appendix D: Regulatory information European standards for electrical safety and electromagnetic compatibility These control panels have been designed in accordance with the following European standards for electrical safety and electromagnetic compatibility: • EN 62368-1 • EN 50130-4 • EN 61000-6-3 •...
  • Page 170 Appendix D: Regulatory information 2X-A Series Installation Manual...
  • Page 171: Index

    Index control panel configuration load, 84 acoustic indications, 14 restore default, 85 alarm display format (VdS Settings), 82 restore previous, 84 area configuration, 107 save, 85 autosetup, 98 custom screens, adding, 87 battery DACT compatible batteries, 28 CMS configuration, 93 fault indications, 135 Ethernet configuration, 92 installation location, 28...
  • Page 172 Index disable device, 58 ID configuration, 69 device type, 58 indications input, 110 acoustic, 14 output, 111 LED, 7 remote, 127 input zone, 104 activation characteristics, 36 activation test, 60 configuration, 108 email connections, 36 accounts, 77 types, 108 manage accounts, 57 installer user level, 46 server configuration, 77 internal printer...
  • Page 173 Index panel activation keys, 95 USB device, removing, 57 password USB flash drive, format, 64 change, 66, 130 user account secure access, 131 create new, 67, 131 timeout period, 47 delete, 67, 131 PSU supervision, 82 edit, 66, 130 public user level, 46 user levels, 46 regional operating modes, 70 ZI initial zone LED, 103...

Table of Contents