Subscribe to Our Youtube Channel
Related Manuals for CTC Union A Series
Summary of Contents for CTC Union A Series
- Page 1 “A” Series MIL-Style Connector Kits “A” Series MIL-Style Connector Kits Product Manual Product Manual...
- Page 2 Table of Contents • Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 •...
- Page 3 Introduction This document contains information on the operation, installation and maintenance of the A-style series of connector kits . O-Ring Insert Locking Ring Contacts x2 Backshell Two-Conductor Cable (-) Common Ground (+) Signal Figure 1. 2-Socket Connector Kit Materials O-Ring Insert Contacts x3 Locking Ring...
- Page 4 Part # Connector Kit Parts Material Connector Kit Compatible Temp . Parts # Cables Polycarbonate, 250 °F CK-A2A-175 CB102 316L Stainless (121 °C) CB110 Steel Locking Ring CK-A2A-190 CB111 CK-A2A-250 CB103 CB193 CB802 CB806 CB810 CB811 CK-A2A CK-A2A-310 CB206 CB602 CB606 CB611 Polycarbonate,...
- Page 5 Part # Connector Kit Parts Material Connector Kit Compatible Temp . Parts # Cables Polyphenylene 392 °F CK-A2S-175 CB102 Sulfide (PPS), (200 °C) CK-A2S-190 CB111 PPS Locking CK-A2S-250 CB802 Ring CB806 CB811 CK-A2S-310 CB206 CB602 CK-A2S CB606 CB611 Table 1. 2-Conductor Product Selection Guide...
- Page 6 Part # Connector Kit Parts Material Connector Kit Compatible Temp . Parts # Cables Polycarbonate, 250 °F CK-A3A-175 CB112 316L Stainless (121 °C) CK-A3A-250 CB812 Steel Locking Ring CK-A3A-310 CB612 CK-A3A Nylon, 316L 250 °F CK-A3N CB112 Stainless Steel (121 °C) CB612 Locking Ring CB812...
- Page 7 Assembly for Ck-A2x Series Strip outer jacket of wire .300 in . 0 .300 in . Cut off shield and drain wire (for twisted shielded wires only) . Strip the insulation of two conductor wires back .200 in . 0 .200 in .
- Page 8 Attach O-ring to the front of the insert . Using a fine-tipped punch, gently press each contact into the appropriate position on the insert . Install accelerometer red (+) wire into the insert socket for Pin A . Install accelerometer black (-) wire into insert socket for Pin B . Slide the knurled ring over the threaded section of the insert until the metal step inside the ring catches on the plastic lip of the insert .
- Page 9 10 . Place the assembled connector body horizontally with the two small epoxy injection holes level and facing upward . 11 . Mix epoxy . Using a syringe, fill the backshell with epoxy through one of the small injection holes until epoxy begins to seep from the other . 12 .
- Page 10 Assembly for Ck-A3x Series Strip outer jacket of wire .300 in . 0 .300 in . Cut off shield and drain wire (for twisted shielded wires only) . Strip the insulation of three conductor wires back .200 in . 0 .200 in .
- Page 11 Attach O-ring to the front of the insert . Using a fine-tipped punch, gently press each contact into the appropriate position on the insert . Install accelerometer red (+) wire into the insert socket for Pin A . Install accelerometer black (-) wire into insert socket for Pin B . Install accelerometer white (+) wire into the insert socket for Pin C .
- Page 12 10 . Place the assembled connector body horizontally with the two small epoxy injection holes level and facing upward . 11 . Mix epoxy . Using a syringe, fill the backshell with epoxy through one of the small injection holes until epoxy begins to seep from the other . 12 .
-
Page 13: Maintenance
Maintenance Once the product has been installed, minimal maintenance will be required . Basic visual checks to ensure integrity should be made periodically . General There are no customer-replaceable parts . The product has been designed for trouble-free service under normal operating conditions . Warranty &...
Need help?
Do you have a question about the A Series and is the answer not in the manual?
Questions and answers