Table of Contents

Advertisement

Quick Links

Dishwasher
SM...
SB...
en Instruction manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMS88TW06G and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Bosch SMS88TW06G

  • Page 1 Dishwasher SM... SB... en Instruction manual...
  • Page 2 (08@HP`h)")*)2):)B)JX)R 1"1*121:1B1J1R1Z1b1j9"9*929:9B9J...
  • Page 3: Table Of Contents

    Table of contents e n I n s t r u c t i o n m a n u a l Intended use ....5 Water softening system / special salt .
  • Page 4 Additional functions ..36 Cleaning and maintenance ....42 Save time (VarioSpeedPlus) ..36 Overall status of the dishwasher .
  • Page 5: Intended Use

    Intended use en Intended use Safety instructions This appliance is intended T his appliance may be used by ■ I n t e n d e d u s e S a f e t y i n s t r u c t i o n s for use in the home and children over the age of 8 years domestic environments.
  • Page 6: Before You Switch On The Appliance

    en Safety instructions Before you switch ON the Installation appliance Following installation, ensure ■ Please read the instructions for that the back of the use and installation carefully. dishwasher is not freely They contain important accessible (protection information on how to install, against contact due to hot use and maintain the appliance.
  • Page 7 Safety instructions en If the dishwasher is installed Install built-under or ■ ■ below or above other integratable appliances only domestic appliances, follow under continuous worktops the information for which have been screwed to installation in combination adjacent cupboards to with a dishwasher in the ensure stability.
  • Page 8: In Daily Use

    en Safety instructions In daily use Warning Risk of injury! Read and observe the safety To prevent injuries, e.g. information and instructions for ■ caused by stumbling, open use on the packaging for the dishwasher only briefly in cleaning and rinsing agents. order to load and unload the Ensure that you follow the dishwasher.
  • Page 9 Safety instructions en Ensure that children do not Warning ■ place fingers in the tablet Risk of explosion! collecting tray 1B. Small Do not add any solvents to the fingers could become caught rinsing compartment. Danger of in the slots. explosion! When opening and closing ■...
  • Page 10: Door Lock

    en Safety instructions Childproof lock (door lock) * Open the door with activated T he child-proof lock (door lock) child-proof lock (door lock) as D o o r l o c k protects children from potential follows: Press the catch of the hazards which the dishwasher child-proof lock to the right poses.
  • Page 11: Environmental Protection

    Environmental protection en Environmental Getting to know your protection appliance B oth the packaging of new appliances D iagrams of the control panel and the E n v i r o n m e n t a l p r o t e c t i o n G e t t i n g t o k n o w y o u r a p p l i a n c e and the old appliances themselves interior of the appliance can be found at...
  • Page 12: Appliance Interior

    en Getting to know your appliance Appliance interior Info button { T he Info button { can be used to 1" Interior light * I n f o b u t t o n display additional programme 1* Cutlery drawer * information.
  • Page 13: Initial Start-Up

    Getting to know your appliance en Initial start-up When the dishwasher is switched on for On the display window at the top @ the first time, you are taken directly to the following text appears for manual the settings for the initial start-up. selection: Scroll with <...
  • Page 14: Settings

    en Getting to know your appliance Settings The dishwasher has been preset with To change the setting: certain settings for your convenience. Open the door. However you can also change this Switch on ON/OFF switch (. factory setting. Press Info button { 8 for 3 seconds until the following text is indicated on the display window at the top @...
  • Page 15 Getting to know your appliance en Basic setting Factory setting Infotext; by pressing Info button { ExtraDry Improved drying for glasses and plastic tableware. Water connection * Cold water The dishwasher can be connected to either hot (40-60°C) or cold water (<40°C).
  • Page 16: Home Connect

    en Home Connect Notes Home Connect The “Network login” menu option is ■ not available unless Wi-Fi has been T he availability of the Home Connect switched on. H o m e C o n n e c t function depends on the availability of The “Connect to App”...
  • Page 17: Setting Up Home Connect

    Home Connect en Setting up Home Connect Network login You can set your dishwasher by The “Network login” menu option is not pressing the remote start button })" available unless you have activated or proceed as follows: Wi-Fi. In the “Network login” menu you can Open the door.
  • Page 18: Connect To App

    en Home Connect Connect to App About data protection: When your Home Connect dishwasher The “Connect to App” menu option is is connected for the first time to a WLAN not available unless there was a network, which is connected to the connection to the home network.
  • Page 19: Remote Start Button

    Home Connect en Remote start button } Wi-Fi without a connection to the Home Connect server ƒ W hen the dishwasher is connected to R e m o t e s t a r t b u t t o n the home network, activate the Y ou can use the Home Connect app dishwasher remote control by pressing...
  • Page 20: Activating Energy Manager

    en Home Connect Activating energy manager „ This is how to set up the energy manager „: To start the energy manager „ , you Open the door. A c t i v a t i n g e n e r g y m a n a g e r must activate the remote start button } Switch on ON/OFF switch (.
  • Page 21: Deactivating Energy Manager

    Home Connect en Deactivating Software update * energy manager „ Y ou can update your dishwasher S o f t w a r e u p d a t e software using the software update The menu option “Disconnect with +” is function (for example optimisation, D e a c t i v a t i n g e n e r g y m a n a g e r available when the dishwasher is...
  • Page 22: Remote Diagnostics

    Declaration of Conformity depends on the degree of hardness of R obert Bosch Hausgeräte GmbH your tap water (see following water D e c l a r a t i o n o f C o n f o r m i t y hereby declares that the appliance hardness table).
  • Page 23: Adjusting The Water Softening System

    Water softening system/special salt en Adjusting the water softening Using special salt system As soon as the low salt indicator P is lit on the control panel or is requested The amount of salt dispensed can be on the front display * ):, salt should set from 0 to 62°E.
  • Page 24: Using Detergents With Salt Component

    en Rinse aid Using detergents with salt Rinse aid component I f combined detergents with a salt As soon as the low rinse-aid indicator D e t e r g e n t w i t h a s a l t c o m p o n e n t component are used, special salt can R i n s e a i d H is lit on the control panel or is...
  • Page 25: Setting Amount Of Rinse Aid

    Rinse aid en Setting amount of rinse aid Top up the rinse-aid as follows: Open dispenser 92; press lug on The amount of rinse aid to be the lid (1) and lift (2). dispensed can be set from 0 to 6. Set the amount of rinse aid to be dispensed to 5 to obtain a very good drying result.
  • Page 26: Utensils

    en Utensils Loading the dishwasher Utensils Remove large food remnants. It N ot suitable is not necessary to prerinse utensils U t e n s i l s under running water. Cutlery and utensils made of wood. Place the utensils so that ■...
  • Page 27: Lower Basket

    Utensils en Utensils must not be placed Heavily soiled utensils (pans) Note: Tip: above the tablet collecting tray 1B. should be placed in the lower basket. These may block the lid of the detergent The more powerful spray jet provides a dispenser and prevent it from opening better dishwashing result.
  • Page 28: Etagere

    en Utensils Etagere * You can take out the cutlery drawer. T he etagere and the space underneath E t a g e r e can be used for small cups and glasses or for larger items of cutlery, such as wooden spoons or serving cutlery.
  • Page 29: Folding Spikes

    Utensils en Folding spikes * Knife rack * * Depending on the features of your * Depending on the features of your F o l d i n g s p i k e s K n i f e r a c k dishwasher, the spikes can be folded dishwasher, the upper basket is fitted down.
  • Page 30: Baking Sheet Spray Head

    en Utensils Baking sheet spray head * Unloading the dishwasher * depending on the features of your To prevent water from dripping off the B a k i n g s h e e t s p r a y h e a d dishwasher upper basket onto the utensils in the Large trays or grilles as well as large...
  • Page 31: Upper Basket With Side Levers

    Utensils en Upper basket with side levers Appliance height 86.5 cm With cutlery basket Upper Lower Pull out upper basket 12. basket basket Hold the sides of the basket along Setting 1 max. ø 24 cm 34 cm the upper edge. This prevents it from suddenly Setting 2 max.
  • Page 32: Detergent

    en detergent Adding detergent Detergent If the detergent dispenser 9: is still Y ou can use tablets as well as powder closed, actuate locking bar 9B to d e t e r g e n t or liquid detergents for dishwashers, but open it.
  • Page 33: Combination Detergent

    detergent en If the utensils are only lightly If programmes are short, tablets may Tip: ■ soiled, slightly less than the indicated not have full cleaning effect due to amount of detergent is usually different dissolving properties and adequate. there may even be undissolved Suitable detergents and care products detergent residue.
  • Page 34: Overview Of Programmes

    en Overview of programmes Overview of programmes T he max. possible number of programmes is illustrated in this overview. The O v e r v i e w o f p r o g r a m m e s corresponding programmes and their arrangement can be found on the fascia.
  • Page 35: Programme Selection

    Overview of programmes en Type of dish Type of soiling Programme Possible Programme sequence additional options Time-optimised: u / t / part dried, common Cleaning 60° mixed utensils household food Intermediate rinse and cutlery remnants Rinsing Short 60°C Drying sensitive Time-optimised: ñ...
  • Page 36: Additional Functions

    en Additional functions Ï IntensiveZone * Additional functions P erfect for a mixed load. You can wash I n t e n s i v e Z o n e very soiled pots and pans in the lower * Depending on the features of your A d d i t i o n a l f u n c t i o n s basket together with normally soiled dishwasher, you can select different...
  • Page 37: Operating The Appliance

    Operating the appliance en AquaSensor * Operating the * depending on the features of your appliance A q u a S e n s o r dishwasher The Aqua sensor is an optical P rogramme data measuring device (light barrier) which O p e r a t i n g t h e a p p l i a n c e measures the turbidity of the rinsing The programme data (consumption...
  • Page 38: Zeolith Drying

    en Operating the appliance ¼ Time display Zeolith drying Warning The running time is determined during Z e o l i t h d r y i n g the programme by the water Risk of burns from touching the blow temperature, the number of utensils as opening 1R! well as the degree of soiling and may...
  • Page 39: Extradry

    Operating the appliance en extraDry emotionLight (interior lighting) * The final rinse uses a higher * Depending on the features of your temperature which improves the drying E m o t i o n L i g h t dishwasher result.
  • Page 40: Infolight

    en Operating the appliance Infolight * Greeting * depending on the features of your When you switch on the dishwasher, the i n f o L i g h t dishwasher brand logo appears. You can switch off While the programme is running, a light the brand logo.
  • Page 41: Time Preselection

    Operating the appliance en Time preselection Programme end You can delay the start of the * The programme has ended when programme by up to 24 hours. “Finished” is indicated on the display Depending on the setting of the time window at the top @ and on the front display, the end of programme is display * ):.
  • Page 42: Interrupting The Programme

    en Cleaning and maintenance Interrupting the programme Cleaning and maintenance Caution! Expansion (overpressure) may cause the appliance door to jump open and/or A regular inspection and maintenance water to escape! If the door was opened C l e a n i n g a n d m a i n t e n a n c e of your machine will help to prevent on an appliance which has a hot water faults.
  • Page 43: Machine Care

    Cleaning and maintenance en ‰ Notes Machine Care Only clean the appliance with ■ M achine Care used in combination with special detergents/appliance M a c h i n e C a r e commercially available machine cleaners which are suitable for use cleaning detergent is a suitable with dishwashers.
  • Page 44: Special Salt And Rinse Aid

    en Cleaning and maintenance Special salt and rinse aid After each washing cycle check the filters for residue. Top up the salt and/or rinse aid as soon Unscrew filter cylinder as illustrated as the refill indicators on the fascia P and take out filter system.
  • Page 45: Spray Arms

    Fault, what to do? en Spray arms Fault, what to do? Limescale and contaminants in the rinsing water may block nozzles and E xperience has shown that you can F a u l t , w h a t t o d o ? bearings on the spray arms 1: and rectify most faults which occur in daily operation yourself.
  • Page 46: Error Message

    en Fault, what to do? Error message Clean the waste water pump as follows: Some faults are indicated at the top of Disconnect the dishwasher from the the display window @ and on the front power supply. display * ): and possible remedies Take out top basket 12 and bottom are offered (for example Filter system basket 9*.
  • Page 47: Fault Table

    Fault, what to do? en Fault table Fault Reason Remedial action Fault code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Water supply turned off. Turn on water supply. Water supply jammed or Turn on water supply. calcified.
  • Page 48 en Fault, what to do? Fault Reason Remedial action Fault code “:ƒ… is lit. Waste-water hose kinked or Install hose without kinks, remove any blocked. residue. Siphon connection still sealed. Check connection to siphon and open if required. Cover on the waste water pump Lock cover correctly.
  • Page 49 Fault, what to do? en Fault Reason Remedial action The Machine Care display Machine Care is recommended. Run the Machine Care programme using a lights up. * special dishwasher cleaning agent and without loading any utensils. The display will go out automatically after three wash cycles whether or not the Machine Care programme is carried out.
  • Page 50 en Fault, what to do? Fault Reason Remedial action Appliance interior wet after No appliance fault. On account of the “Condensation drying” wash cycle. principle, water droplets are physically induced and required in the container. The humidity in the air condenses on the inner walls of the dishwasher, drains and is pumped out.
  • Page 51 Fault, what to do? en Fault Reason Remedial action Detergent residue Detergent dispenser cover 9: Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully.
  • Page 52 en Fault, what to do? Fault Reason Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9...
  • Page 53 Fault, what to do? en Fault Reason Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; Do not prerinse utensils. Remove only sensors therefore decide on large food remnants. weak programme sequence. Increase sensitivity of the sensors.
  • Page 54 en Fault, what to do? Fault Reason Remedial action Appliance cannot be Malfunction. Disconnect appliance from the power switched on or operated. supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply.
  • Page 55 Fault, what to do? en Fault Reason Remedial action Filling valves making Depends on domestic installation, No remedial action possible. striking noises. as no appliance fault. No effect on appliance function. Knocking or rattling noise. Spray arm strikes the utensils, Position utensils so that the spray arms do utensils not positioned correctly.
  • Page 56: Installation And Connection

    en Customer service Customer service Installation and connection I f you are unable to rectify the fault, C u s t o m e r s e r v i c e please contact your customer service. T he dishwasher must be connected We will always find an appropriate I n s t a l l a t i o n a n d c o n n e c t i o n correctly, otherwise it will not function...
  • Page 57: Contents Of Package

    Installation and connection en Contents of package Technical specifications If you have any complaints, contact the Weight: ■ dealer from whom you purchased the up to 60 kg appliance or our customer services. Voltage: ■ 220–240 V, 50 Hz or 60 Hz Dishwasher ■...
  • Page 58: Installation

    en Installation and connection Installation Drinking water connection The required installation dimensions Fasten the drinking water connection can be found in the installation to the tap according instructions. Level the appliance with to the installation instructions using the aid of the height-adjustable feet. the enclosed parts.
  • Page 59: Warm Water Connection

    Installation and connection en Warm water connection * To change the setting: Open the door. * depending on the features of your Switch on ON/OFF switch (. W a r m w a t e r c o n n e c t i o n dishwasher Press Info button {8 for 3 The dishwasher can be connected...
  • Page 60: Electrical Connection

    en Installation and connection Electrical connection Removal Connect the appliance to an Also observe ■ alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz Disconnect the appliance from the via a correctly installed socket with power supply.
  • Page 61: Transporting

    Installation and connection en Transporting Protection against frost I f the appliance is in a room where Empty the dishwasher and secure loose P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) there is a risk of frost (e.g.
  • Page 62 *9001397770* 9001397770 (9810) 642 TW...

Table of Contents