Speakman Commander SC-1210-AF Installation Instructions

INSTALLATION INSTRUCTIONS
SC-1210-AF
Commander
®
Exposed Shower System
NEED HELP?
For additional assistance or service please contact:
PRODUCT PREPARATION
Slide the Strap (A) onto the Shower Arm.
1
Then apply sealant to inlet threads of
Shower Arm and the Plug (B). Screw the
Shower Arm into the Valve Body (C).
Tighten and position outlet perpendicular
with Valve Body. Use Adjustable Wrench to
tighten the Plug (B) into the Valve Body
(C).
A
C
B
NOTE: If water supplies are entering from
below, rotate the Valve Body 180° before
installing Shower Arm and Plug
TOOLS & SUPPLIES NEEDED
Pencil Measuring Level
Tape
Drill Drill Bit Mounting
3/16" Hardware
(Included)
Pipe Phillips Adjustable
Wrench Screwdriver Wrench
Thread Seal Eye Protection
Tape
www.speakman.com
800-537-2107
ROUGH IN SUPPLY LINES
Following the rough-in dimensions located
2
ot the end of this manual, install Supply
Pipes at proper location. See images
below for reference. Apply pipe sealant to
one end of Supply Pipes (provided). Screw
pipes into supply lines.
8 7
"
16 16
215mm 215mm
6 3
"
SUPPLY
16 16
157mm 157mm
5 1
"
2
143mm 143mm
18 1
18 "
2
470mm 470mm
4'-6' 4'-6'
137 Meters 137 Meters
TO FLOOR TO FLOOR
1¹⁄ "
8
MOUNTING DEPTH
NOTE: Supply lines must have 1/2 NPT
female threaded ends and be 1-1/8" from
center of supply line to finished wall.
IMPORTANT
SAFETY TIPS:
Be sure to read and understand all instructions
before beginning installation.
Inspect all connections after installation.
Cover the drain to avoid loss of parts.
Be sure to wear proper eye protection.
Do NOT over tighten any connections or damage
may occur.
Shut OFF water supplies before beginning
installation.
Observe all local plumbing and building codes.
Ensure proper structure is in place to support the
Valve and plumbing during use.
VALVE SPECIFICATIONS:
This product does not include a balance pressure
or thermostatic valve. Sudden water temperature
changes may be experienced if there are sudden
changes to the water's supply pressure or
temperature.
IMPORTANT: Shut off water supplies.
Supplies must be on 6" centers.
Recommended height from center of valve
body to floor is 54". Valve body is reversible to
take supplies from below.
SUPPLY LINE ADAPTERS
Apply sealant to threads of Supply Lines
3
(A). Slip Coupling Nuts (B) onto Supply
Lines and screw Swivels (C) up hand tight.
Gripping on small diameter of Swivels with
a Pipe Wrench, tighten pipes and/or
Swivels.
LINE
B
A
C
FINISHED
WALL
SURFACE
CAUTION
Freeze damage to the shower unit will void the warranty.
It is important to properly winterize the complete shower
unit. The unit MUST be drained of all water in freezing
conditions. This includes removing the Valve Cartride(s)
and the Shower Head from the unit. Store Valve
Cartridge(s) and Shower Head indoors.
CAUTION: When outdoor temperature rises
above 90 degrees, use caution to prevent
scalding from water stored within the unit. It is
recommended to flush the unit by turning it on
for 30 seconds before entering the shower
water. This will avoid accidental scalding by the
user and ensure safe use of the shower unit.
MAINTENANCE
The shower valves are washer-less and require
no routine maintenance.
Your new product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. Avoid
abrasive cleaners, steel wool, and harsh
chemicals as these will dull the finish and void
your warranty.
To remove the index button on the vandal
resistant handles, locate knockout hole on handle
underneath one of the arms of the handle. Insert
a rigid pin (1/8" diameter or smaller) into hole and
knockout index button.
92-SC-1210-AF-02
INSTALL VALVE TO INLETS
Place Rubber Washers (A) on inlets of
4
Valve Body and position body assembly up
to Swivels and tighten Coupling Nuts.
NOTE: Shower Arm Strap location
optional. Disconnect assembly from supply
lines.
A