Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
Electric Fire
This product is only suitable for well insulated
spaces or occasional use.
IMPORTANT
The fan will run for approximately 15 seconds after the heater is
turned off. This is to remove any residual heat from the fire to
prevent any potential overheating.
www.firedupcorporation.com/manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fired Up Corporation HW36
Summary of Contents for Fired Up Corporation HW36
- Page 1 INSTRUCTION MANUAL Electric Fire This product is only suitable for well insulated spaces or occasional use. IMPORTANT The fan will run for approximately 15 seconds after the heater is turned off. This is to remove any residual heat from the fire to prevent any potential overheating.
-
Page 2: Table Of Contents
Read ALL the instructions before use. These instructions are for your safety. Please read through them thoroughly before use and retain for future reference. Failure to follow them could cause injury and/or property damage. CONTENTS SECTION 01 Cautions 03-04 Introduction Handling SECTION 02 Unpacking &... -
Page 3: Cautions
CAUTIONS DO’S • Read ALL the instructions before using this product. • Only use this product for its intended use as described in this manual. • Always use the product in accordance with this guide. If in doubt obtain expert advice. - Page 4 IMPORTANT! This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Page 5: Introduction
INTRODUCTION Thank you for choosing this product. It is designed to meet the most stringent quality, performance, and safety requirements. This guide aims to improve your understand- ing and appreciation of your new product by providing simple and informative instructions. HANDLING Before continuing any further with the installation of this product please read the following:... -
Page 6: Dimensions
DIMENSIONS Model No. HW36 914mm 500mm 120mm 470mm 762mm 267mm 715mm HW42 1067mm 500mm 120mm 470mm 914mm 267mm 867mm 1270mm 500mm 120mm 470mm 1117mm 267mm 1070mm HW50 HW60 1524mm 500mm 120mm 470mm 1372mm 267mm 1324mm 1828mm 500mm 120mm 470mm 1676mm 267mm 1628mm... - Page 7 Wall Mounting Remove 2 x screws holding the glass in place, then remove the glass. Remove 2 x screws that secure the wall bracket to the fire. Then remove the 2 x screws that secure the fixing plate to the fire.
- Page 8 Mark the holes required for the wall bracket. Ensure these holes are level and drill 6mm diameter holes approximately 35mm deep. Insert the wall plugs and screw the wall bracket to the wall. Hang the fire on the wall bracket. Mark the hole for the bottom bracket and drill a 6mm diameter hole approximately 35mm deep.
- Page 9 Fitting into a Wall Follow these steps if the fire is being fitted into the wall. Remove 2 x screws holding the glass in place, then remove the glass. See “Wall Mounting step 1” for illustration. Insert the fire into the wall/frame and using 4 x screws and the appropriate fixings, secure the fire to the wall.
-
Page 10: Opening Dimensions For Frame/Wall
Opening Dimensions for Frames/Wall Installation Model No. HW36 770mm 480mm 120mm HW42 922mm 480mm 120mm HW50 1126mm 480mm 120mm HW60 1378mm 480mm 120mm HW72 1682mm 480mm 120mm CONTROL P Control Panel / Remote Control Operation CONTROL PANEL MANUAL KEY BOA... - Page 11 Oper NOTE: The unit m Remote control and it is NOTE: The functi NOTE: The unit m ensure th and it is c TEMP+ POWER NOTE: The functio ensure the TEMP- Powerin Press the FLAME PICTURE functions Powering in a stand HEATER -ature will Press the...
- Page 12 (continued) tion y emit a slight, harmless odour and smoke when first used. This odour & smoke is normal OPERATION - Manual used by the internal heating of the internal heater parts and will not occur again. On/Off switch must be switched on for the fire to work. The switch is in the ON position when below can be controled either by key board or remote control, before the POWER button, emit a slight, harmless odour and smoke when first used.
- Page 13 Setting the Tim Ember Color button, you can ifferent Ember Color options - different Ember Color options - Press the Press & Flame effect & colour for two s (continued) ration Fig 1 (n Press th Six themes can be selected using the setting flame effect button , the corresponding...
- Page 14 Setting the Time Temp - butto & Day (24 Hour Clock) Press the T Press the Press the Time Setting button & the minute Press the Time Setting button & the minute Press the T Press the P HEATER ower button to turn the unit on. setting will setting will setting will flash.
-
Page 15: Set Timers
Day (24 Hour Clock) NOTE: Th e Setting button & the hour e Setting button & the hour Press the Power button to turn the unit on. Temper Press & hold the Time Setting button e Setting button & the hour wer button to turn the unit on. -
Page 16: Additional Features
When the heater is on operation (H1 or H2), once the fan will run for approximately 30 mponents from any potential Close the window or cooling items, push ure setting Press the Power button again to turn off all functions. ambient temperature drops 5°C within 10 minutes, the nds after the Heating function is rheating. -
Page 17: Technical Parameters
mum Setting y remote control. seconds pressing the Brightness button to mediate Setting operatin llowing levels-see Fig : um Setting settings, TECHNICAL PARAMETERS the timer L 193/88 Official Journal of the European Union 21.7.2015 brightness setting can be only see Fig 1 mum Setting y remote control. -
Page 18: Troubleshooting
d the unit will default into normal played. operating Having conf will move to the 1st ON/OFF period (M1) for Press the Time Setting button & the display mode. To activate the timer Repeat ste settings, p Tuesday with the 1st ON time setting dis timer setting will move to the 1st OFF time setting - see played. -
Page 19: Conformity With Directives
ode. To activate the timer ed Sunday’s settings, exit the Tuesday with the 1st ON time setting dis Fig 1 . with the 2nd ON time setting displayed. NOTE: The time & day must be set before the in the timer mode using the Heater function. will move to the 1st OFF time setting - see seconds and the unit will default into normal Press the Power button to turn the unit on. -
Page 20: Guarantee & Contacts
This product guarantee does not affect your statutory rights. CUSTOMER HELPLINE +44 (0) 3300 882 069 customer.support@firedupcorporation.com Fired Up Corporation Ltd Fired Up Buildings HD1 3LF, UK www.firedupcorporation.com Fired Up Corporation (Ireland) Ltd...
Need help?
Do you have a question about the HW36 and is the answer not in the manual?
Questions and answers