UniPOS FD8020S Instruction Manual

ПОЖАРОИЗВЕСТИТЕЛ ТОЧКОВ
ТОПЛИНЕН МАКСИМАЛЕН
ПАСПОРТ
.
FD8020S 8000.
( .1)
( .5).
( .3) 360°
- - ;
- - .
. 24V DC
. 10V DC
. 30V DC
" " 80µA/22.5V DC
" " 8mA/10V DC; 25mA/30V DC
2 S (
" " ( RI/KL)
IP 43 (
(93±3)%
Ø100mm, h=47mm
8000 0.100kg
(0.8-1.5)mm
8000 (
(
( .1, .2).
( .3.2). (
( .1) ( .2).
( .4) ,
.
.
1.
2. , ,
" " 40s.
3. - 2 .
1. -
2. -
3.*
* .
36
-
.
-
,
. -
.
Manufacturer: UniPOS Ltd., 47 San Stefano Street, Pleven 5800, Bulgaria, http://www.unipos-bg.com
FD8020S
тип
2821
08-8020S-04-21
,
.
( .4),
:
EN 54-5:2017 + A1:2018)
10m (EN54)
8m (EN54)
RI 31
UL)
10°C 50°C
40°C
,
).
.
.2.
.1, .1)
( .3.1).
.4). ( .3)
:
,
.
.
" ".
:
- 6
( .1, .6).
.
.
,
,
S36102
GENERAL DESCRIPTION
The re detector is designed for early warning of a re condition when the xed temperature threshold in the
protected premises is reached. The principle of functioning of the re detector is based on the ohmic resistance
alteration in the thermistor as a result of the ambient temperature change. FD8020S is tted on bases series 8000.
The re detector ( g.1) consists of a printed circuit board and a chamber with thermistor (pos.4), xed in a
plastic body (pos.5).
Both LED indicators (pos.3) allow range of visibility 360° and provide information for the status:
-Standby mode - the LEDs are o ;
-Alarm condition - the LEDs are on.
TECHNICAL DATA
Nominal operating voltage
Minimum operating voltage
Maximum operating voltage
Current consumption in Standby mode
Current consumption in Alarm mode
Temperature category
Protected area
Height of mounting
Output in Alarm condition (RI/KL terminal)
Degree of protection
Operational temperature range
Relative humidity resistance
Dimensions, base included
Weight, base 8000 included
.
Type of the connecting line to the base
Cross section of the connecting wire
.
INSTALLATION
The re detector operates with bases type 8000. They are delivered separately and installed on ceiling through
,
relevant screw with plastic-dowel. The connection diagram of the installation is on g.2.
Cable shoes is recommended in the wiring installation.
The re detector is placed on the base ( g.1,pos.1).
,
It is rotated clockwise until reaching the guiding grooves ( g.1,pos.2). It is rotated until rest ( g.3.1).
.
The slots of the base and the body should match ( g.3.2).
Locking of the re detector ( g.4). Before installation, the key (pos.3) is detached from the base and the rib (pos.1) of
the locking click (pos.2) is cut out. Removing of a re detector locked to the base. Insert the key into the slot (pos.4)
push in as in the same time the re detector is rotated anticlockwise. Remove the key and continue to rotate the
re detector in the same direction until it is released from the base.
TESTING
The re detector is tested after installation as a part of the site's re alarm system or with the following maintenance
procedure:
1. The conventional line of the re detector is power supplied from the Fire Control panel's zone or from auxiliary power
supply unit;
2. One minute after the re detector has been power supplied, then it is triggered with heat tester. It should enter to re
alarm condition within 40 sec.
3. In order to reset the FD8020S re detector, then the conventional line must be power down for at least 2 sec. or a reset
command should be handled from the Fire Control Panel;
,
,
CONVENTIONAL FIXED TEMPERATURE
HEAT DETECTOR
FD8020S
TYPE
INSTRUCTION MANUAL 08-8020S-04-21
24 V DC
10 V DC
30 V DC
80µA/22.5V DC
8mA/10V DC; 25mA/30V DC
2 S (complies with EN54-5:2017 + A1:2018)
circle with diameter 10m (complies with EN54-14)
up to 8m (complies with EN54-14)
for RI 31
IP 43 (not veri ed by UL)
minus 10°C - plus 50°C
(93±3)% at 40°C
Ø100mm, h=47mm
0.100kg
two-wire, a single-core or
multi-core insulated wire
(0.8-1.5)mm
Manufacturer: UniPOS Ltd., 47 San Stefano Street, Pleven 5800, Bulgaria, http://www.unipos-bg.com
2821
S36102