UniPOS FD8060 Instruction Manual

ПОЖАРОИЗВЕСТИТЕЛ ТОЧКОВ
ОПТИЧНО-ДИМЕН И ТОПЛИНЕН
тип
ПАСПОРТ
, -
.
, .
.
( .1) ,
( .5).
( .3) 360°
-
- ;
-
- ;
-
–
.
.
.
" "
" "
" "
" " ( RI/KL)
8000 (
.
.2.
( .1,
( .1, .2). (
( .3.2).
( .4).
( .2).
.
.
:
1.
2. ,
, .
3.
- 2s
" "
1.
2.
3.*
* .
. ( .1,
,
. ,
,
" ".
36 .
-
.
-
Manufacturer: UniPOS Ltd., 47 San Stefano Street, Pleven 5800, Bulgaria, http://www.unipos-bg.com
FD8060
2821
06-8060-04-21
.
.
( .4) ( .9).
:
1s.
24V DC
10V DC
30V DC
130 µA/22.5V DC
8mA/10V DC; 25mA/30V DC
A 2 R ( N 54-5:2017 + A1:2018)
EN 54-7:2018
40s
2s
40s
EN54-14
EN54-14
RI 31
IP 43 ( UL)
10°C 50°C
(93±3)% 40°C
Ø100mm, h=52mm
0,100kg
(0.8-2.5) mm
).
.
.1)
.3.1).
( .3)
( .4) ,
.
,
24V DC/0,1A.
" "
,
.
40s.
:
-
-
- 6
( .1, .6)
.7) ( .1, .8).
.
"
, -
,
,
, . -
, .
S36102
GENERAL DESCRIPTION
The re detector is designed for early warning of a re condition responding to xed threshold smoke concentration
or rate of rise temperature or xed temperature threshold detected in the protected premises.
The principle of functioning of the optical part is based on scattered light re ected from smoke particles entering the
optic chamber. The principle of functioning of the heat part is based on the ohmic resistance alteration in the thermistor
as a result of the ambience temperature change. The smoke sensitivity and the temperature category are factory preset.
The re detector is microprocessor controlled with implemented algorithm for self-compensation of the chamber
contamination. FD8060 is tted on bases 8000.
The re detector ( g.1) consists of a printed circuit board, an optic chamber (pos.4), and a thermistor (pos.9).
They are xed in a plastic cabinet (pos.5).
Both LED indicators (pos.3) allow range of visibility 360° and provide information for the status:
-Standby mode – the LEDs are o ;
-Alarm condition – the LEDs are on;
-Contaminated chamber — the LEDs ash on a period of 1 sec.
TECHNICAL DATA
Nominal operating voltage
Minimum operating voltage
Maximum operating voltage
Current consumption in Standby mode
Current consumption in Alarm Condition
Temperature category
Smoke sensitivity
Time to enter Standby mode after power supply is on
Reset time
Time to enter Standby mode after reset
Protected area
Height of mounting
Output in Alarm condition (RI/KL terminal)
Degree of protection
Operational temperature range
Relative humidity resistance
( .1)
Dimensions, base included
Weight, base included
Type of connecting cable
Cross section of the connecting wires
TECHNICAL DATA
The re detector operates with bases type 8000. They are delivered separately and are installed on ceiling through
relevant screw with plastic-dowel. The connection diagram of the installation is on g.2.
Cable shoes is recommended in the wiring installation.
40s.
, The re detector is placed on the base ( g.1, pos.1). It is rotated clockwise until reaching the guiding grooves
( g.1,pos.2). It is rotated until rest ( g.3.1). The slots of the base and the body should match ( g.3.2).
Locking of the re detector ( g.4). Before installation, the key (pos.3) is detached from the base and the rib (pos. 1) of
the locking click (pos.2) is cut out.
Removing of a re detector locked to the base. Insert the key into the slot (pos.4) push in as in the same time the re
detector is rotated anticlockwise. Remove the key and continue to rotate the re detector in the same direction until it is
released from the base.
TESTING
". The re detector is tested after installation as a part of the site's re alarm system or with the following maintenance
,
procedure:
1. The conventional line of the re detector is power supplied from the Fire Control panel's zone or from auxiliary power
supply unit;
2. One minute after the re detector has been power supplied, then it is triggered with smoke or heat tester. It should
enter to re alarm condition within 40s;
,
3. In order to reset the FD8060 re detector, then the conventional line must be power down for at least 2 sec. or a reset
command should be handled from the Fire Control Panel;
CONVENTIONAL COMBINED DETECTOR
FD8060
TYPE
INSTRUCTION MANUAL 06-8060-04-21
24 V DC
10 V DC
30 V DC
130 µA/22.5V DC
8mA/10V DC; 25mA/30V DC
2 R (complies with EN 54-5:2017 + A1:2018)
complies with EN 54-7:2018
up to 40s
2s
up to 40s
complies with EN54-14
complies with EN54-14
for RI 31
IP43 (not veri ed by UL)
minus 10°C - plus 50°C
(93±3)% at 40°C
Ø100mm, h=52mm
0.100kg
two-wire
(0.8-2.5) mm
Manufacturer: UniPOS Ltd., 47 San Stefano Street, Pleven 5800, Bulgaria, http://www.unipos-bg.com
2821
S36102