Chapter 1 Features 1. Built in TV channel selector for TV viewing. 2. Simultaneous display of PC and TV images. 3. Connectable to PC’s analog RGB port. 4. Built in HDTV, composite video, HDMI, ATV and DTV, Audio line out, Audio optical out.
4. POWER SUPPLY Input Voltage Level: 100~240 Vac, 50/ 60 Hz Power Consumption: 175W (Max.) Power OFF: to less than 1W (Max.) (at 120 Vac) 5. SPEAKER Built in Speakers:6Ω/10W (max) X 2 way. 6. ENVIRONMENT Operating Temperature: 5℃~35℃ (Ambient) Operating Humidity: Ta= 35℃, 90%RH(Non-condensing) Operating Altitude: 0 - 14,000 ft Non-Operating: 4000 ft...
Page 6
9. Precautions Please pay attention to the followings when you use this TFT LCD module. 9-1. Mounting Precautions (1) You must mount a module using holes arranged in four cornersor four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module.
Page 7
9-2. Operating Precautions (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage: V=±200mV (Over and under shoot voltage) (2) Response time depends on the temperature. (In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer.
Page 8
9-5. Storage When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5°C and 35°C at normal humidity.
Chapter 3 On Screen Display On Screen Display (OSD) is a friendly interface providing the function adjusting in our system. Customers could operate it only by few buttons. There is the introduction of the OSD. <Side> A. LED indicator display on the front LED indicator Status Remark...
Page 10
ii. HOME operation Press button to activate the OSD. Press button to exit. iii. Channel Selection By pressing buttons, channel should be selected. At the time, channel should increase with button and decrease with button. When the “MENU” is activated, it can be navigated up by button and down by button.
Page 11
On Screen Display Operation: Main unit button LGE 2011 UI Adjustment Main Menu Channel Picture Audio Time Option Lock Input My Media CONFIDENTIAL – DO NOT COPY Page 3-3 File No. SG-0000039...
Page 12
Channel A. Auto Tuning B. Manual Tuning a. Type: TV, CATV, DTV, CADTV b. Channel c. Add / Delete d. Close C. Channel Edit a. Type: TV, CATV, DTV, CADTV b. Channel Change c. Add / Delete / Remove Favorite Picture A.
Page 13
f. Tint (R50 ~ G50) [0] g. Advanced Control g-1. Color Temperature (Cool, Medium, Warm) g-2. Fresh Contrast (Off, Low, Medium, High) g-3. Fresh Color (Off, Low, High) g-4. Noise Reduction (Off, Low, Medium, High) g-5. Gamma (Low, Medium, High) g-6.
Page 14
A. Clock (Auto, Manual) a. Year (2011 ~ 2035) b. Month (1 ~ 12) c. Date (1 ~ 31) d. Hour (12AM ~ 11PM) e. Minute (0 ~ 59) f. Time Zone (Eastern, Central, Mountain, Pacific, Alaska, Hawaii) (US model and MX model) g.
Page 15
Option A. Language a. Menu (English, Spanish, French) b. Audio (English, Spanish, French) B. Input Label a. AV (VCR, DVD, Set Top Box, Satellite, Cable Box, Game, PC, HD-DVD, Blu-Ray) b. Component (VCR, DVD, Set Top Box, Satellite, Cable Box, Game, PC, HD-DVD, Blu-Ray) c.
Page 16
Lock A. Lock System (Off, On) (default password: 0000) B. Set Password a. New b. Confirm C. Block Channel a. Type: TV, CATV, DTV, CADTV b. Channel Change c. Block, Un-block D. Movie Rating (Off, X, NC-17, R, PG-13, PG, G) E.
Page 17
Input Component RGB-PC HDMI-1 HDMI-2 HDMI-3 My Media A. Photo List a. Slideshow Mode (Single, Sequence, Shuffle) b. Repeat (Off, On) c. Sort By (Photo Date, File Date, File A-Z) d. Duration (5 ~ 32) [5] e. Slideshow Effect (Random, Dissolve, Wipe Right, Wipe Left, Wipe Up, Wipe Down, Box In, Box Out) f.
Page 18
QMenu A. Aspect Ratio (Set By Program, 4:3, 16:9, Zoom, Cinema Zoom, Just Scan) B. Backlight (0 ~ 6) C. Picture Mode (Vivid, Standard, Cinema, Sport, Game) D. Sound Mode (Standard, Music, Cinema, Sport, Game) E. Caption (Off, On) F. Multi Audio (Mono, Stereo, SAP) G.
Chapter 4 Factory preset timings This timing chart is already preset for the TFT LCD analog & digital display monitors. PC analog preset modes Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 640*350 31.468 70.09 25.17 Х 720*400 31.469 70.08 28.32 640*480 31.469 59.94 25.17...
Chapter 5 Pin Assignment 1 Video Graphics Array (VGA) connector pin assignment The TFT LCD analog display monitors use a 15 Pin Mini D-Sub connector as video input source. Description Green Blue Ground Ground R-Ground G-Ground B-Ground +5V for DDC Ground No Connection (SDA)
3 Signal Specification 3.1 F-Type TV RF connector a. Signal Level 70dBµV typical b. System: NTSC c. Frequency: 55~801MHz (NTSC) 3.2 PC connector 15 pin male D-sub connector a. Pin Assignment Refer to Section 5.1 b. Signal Level Video (R, G, B): Analog 0.7Vp-p/75Ω Sync (H, V): TTL level c.
Page 24
3.5 Component signal a. Frequency H: 15.734KHz V: 60Hz (NTSC-480i) H: 31KHz V: 60Hz (NTSC-480p) H: 45KHz V: 60Hz (NTSC-720p) H: 33KHz V: 60Hz (NTSC-1080i) H: 67.5KHz V: 60Hz (NTSC-1080P) b. Signal level Y: 1Vp-p; Pb: ±0.350Vp-p; Pr: ±0.350Vp-p c. Impedance 75Ω d.
Chapter 6 Main Board I/O Connections J1 CONNECTION [MAIN BD TO POWER BD] Description +5VSB +5VSB +5VSB +12V +12V POWER SW ON OFF BL ON OFF PWM DIM J2 CONNECTION [DOWNLOAD AND DEBUGGING] Description +3V3SB U0RX U0TX CONFIDENTIAL – DO NOT COPY Page 6-1 File No.
Page 26
J3 CONNECTION [JTAG INTERFACE] Description AV33 TVTREF#1 JTRST# JTDI JTMS JTCK Pull High AV33 JTDO N.C. JTAG DBGRQ JTAG DBGACK J14 C [Main Bd To IR/Light Sensor/LED Bd] ONNECTION Description OIRI_in 5VSB LS_SCL LS_SDA DETECT RED_LED BLUE_LED CONFIDENTIAL – DO NOT COPY Page 6-2 File No.
Chapter 7 Theory of Circuit Operation The route of D-SUB 15pin input An RGB (analog) signal is inputted the D-SUB 15pin to the MT5379U which transfers it to a digital signal by the A/D converter. Then MT5379U generates a Low Voltage Differential Signal (LVDS) for display device.
Page 32
The operation of keypad There are Buttons to control and to select the function of 55LV4400. Also, there is a LED back light to indicate the status of operation (Red → STANDBY, Blue → ON). MT5379U Ⅰ. GENERAL DESCRIPTION The MediaTeK MT5379 family consists of a DTV front-end demodulator, a backend decoder and a TV controller and offers high integration for advanced applications.
Functional Block Diagram Ⅱ.FEATURES Host CPU 1. ARM 11 2. 16K I-Cache and 16K D-Cache 3. 16K Boot ROM 4. JTAG ICE interface 5. Watch Dog timer Page 7-4 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 35
Transport Demultiplexer 1. Supports a serial or parallel transport stream input 2. Supports ATSC, DVB transport stream input 3. Supports DES/3-DES/DVB/AES/Multi-2 de-scramblers 4. Up to 8 PIDs even/odd keys for descrambling 5. Supports 32 PID filters and 32 section filters 6.
Page 36
De-mosquito engine 1. 3D de mosquito engine ME/MC engine 1. 5379 support FHD 120Hz 2. Support motion judder compensation 3. Support 24Hz/60Hz to 120Hz, 25Hz/50Hz to 100Hz in100/120Hz panel 4. Support 24Hz/60Hz, 25Hz/50Hz in 50/60Hz panel 5. Support 50Hz to 75Hz for 75Hz panel 6.
Page 37
Video Plane 1. Supports video capture and over scan 2. Flesh tone management 3. Gamma/anti-Gamma correction 4. Color Transient Improvement (CTI) 5. 2D peaking 6. Saturation/hue adjustment 7. Brightness and contrast adjustment 8. Black and White level extender 9. Adaptive Luma/Chroma management 10.
Page 38
CVBS In 1. On chip 54MHz 10-bit video ADC 2. Supports PAL (B,G,D,H,M,N,I,Nc), NTSC, NTSC-4.43 and SECAM 3. NTSC/PAL support 3D comb filter and SECAM supports 2D comb filter 4. Built-in Motion Adaptive 3D Noise Reduction 5. VBI data slicer for CC/TT decoding 6.
S/PDIF interface 1. One SPDIF input 2. One SPDIF out Digital TV (ATSC/Open-Cable) Demodulator 1. Compliant with ATSC digital television standard 2. Supports SCTE DVS-031 and ITU J.83 Annex B digital CATV standard 3. Accepts direct IF (44MHz or 43.75MHz) and low IF (5.38MHz) 4.
Page 41
Peripherals 1. Built-in (T8032) in standby module 2. SDIO interface 3. Support MII/RGMII interface (built-in Ethemet MAC) 4. Three built-in UARTs with Tx and Rx FIFO, one of them has hardware flow control and high speed data transferring 5. Four basic serial interfaces ; one is for the tuner, two is the master for general purpose, the other one extra slave serial interfaces for HDMI EDID data 6.
Page 42
2. DC Characteristics 3. Thermal Characteristics 4. DDR2 ELECTRICAL Characteristics and DC Operating Condition Page 7-12 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 43
5. DDR2 AC Operating Condiction 6. DDR3 ELECTRICAL Characteristics and DC Operating Condition 7. DDR3 AC Operating Condition Page 7-13 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 44
Flash: MX25L6445E Page 7-14 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 45
Page 7-15 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 46
Page 7-16 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 47
Page 7-17 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 48
Page 7-18 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 49
Page 7-19 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 50
Page 7-20 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 51
Page 7-21 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 52
Page 7-22 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 53
Page 7-23 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 54
Page 7-24 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 55
Page 7-25 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 56
Page 7-26 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 57
Page 7-27 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 58
Page 7-28 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 59
Page 7-29 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 60
Page 7-30 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 61
Page 7-31 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 62
Page 7-32 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 63
GDDR3: K4J10324QD-HC12 Page 7-33 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 64
Audio Amplifier: TPA3110LD2 Pin Layout and Internal Block Diagram (Top View) Page 7-34 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 65
Page 7-35 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Page 66
Page 7-36 CONFIDENTIAL – DO NOT COPY File No. SG-0000039...
Chapter 8 Waveforms D_SUB RGB mode: Pixel-clock = 138.35MHz (1920x1080@60Hz ) ; Line Pattern (one white one black) R data(FB63): G data(FB62): B data(FB61): Hsync(FB65) : Vsync(FB64) VGAL_IN (R412) [Audio Input: 1KHz / 1Vrms] VGAR_IN (R416) [Audio Input: 1KHz / 1Vrms] CONFIDENTIAL –...
Page 68
Component Chroma-23291, Timing-1080p, Pattern-100% color bar Component signal Y(FB33) Component signal Pb(FB34) CONFIDENTIAL – DO NOT COPY Page 8-2 File No. SG-0000039...
Page 69
Component1 signal Pr (FB36) Composite Chroma-23291, Timing-NTSC-M CONFIDENTIAL – DO NOT COPY Page 8-3 File No. SG-0000039...
Chapter 9 Trouble shooting MONITOR DISPLAY NOTHING (PC MODE) Start 1. Is Power board output +5VSB &+12? LED is lighted 2. Is J1 connector good? 3. Is DC to DC OK? 4. Is U1 (+5V) working ok? It is in power saving 1.
Page 71
(TV, COMPOSITE, VIDEO) IS NOT DISPLAY CORRECTLY Start 1. Check video Input signal good? 2. Check DVD player 1. Check VIDEO signal 2. Check signal between P6 (IF IN AV P6 input correct? mode) 1. Check U11 :DV33&DV10&AV33&AV12 2. Check Y2 is OK? U11 output correct? 1.
Page 72
(COMPONENT) IS NOT DISPLAY CORRECTLY Start 1. Check video Input signal good? 2. Check host’s setting 1. Check signal between P6 P6 input correct? 2. Check power 12V& 5V 1. Check signal between U14 2. Check U11 Clock (27MHZ) U11 input correct? 3.
Page 73
HDMI ) IS NOT DISPLAY CORRECTLY Start 1. Check video Input signal good? 2. Check host’s setting 1. Check U11 power 2. Check between signals U11 U11 no data out ? 3. Check U11 clock 27MHZ 1. Is TCN3 & TCN4 connected good? 2.
Page 74
TROUBLE OF DC-DC CONVERTER Start The voltage is 5VSB 1. Check power board 2. Check power cable J1 PIN1,2,3 connection J1 The voltage is +12V while power switch on 1. J1 connection good J1 PIN 8,9 2. Check power board The voltage is +5V while power U1 pin 5 6 7 8 switch on...
Page 75
TROUBLE OF DDC READING Start Support DDC1/2B 1. VGA cable ok? 2. Check signal (U35 to P13) Analog DDC OK? 3. Check U35 Voltage 4. Is compliant protocol? Support DDC1/2B 1. HDMI cable ok? 2. Check signal (U19 to P8) HDMIDDC OK? 3.
Page 76
(TV_SIDE, AUDIO) IS NOT DISPLAY CORRECTLY Start Check Audio source Input signal good? Check the player of source Check signal of Main Board Check amplifier (J15) Input correct? Check MT5379 audio out, R109, R111 Check signal correct? Check 12V of U48. Check amplifier OK? –...
A C I N L E T S T - 0 1 E K - B C C - 0 3 + V H R 3 P 4 5 0 / 1 5 0 m m LG PANEL 0460-3008-0120 W H P 2 4 0 1 8 / P 2 4 0 1 8 1 5 7 1 # 2 8 7 5 0 m m...
Page 95
POWER CORD 1800mm 125V UL/CSA 90' LF 365502420393 060360000030 BATTERY ALKALINE 1.5V AAA LR03 DMEGC consign parts LF 365502420393 060360000010 Battery Alkaline 1.5V AAA (601-LR03) ROCKET 365502420393 098003064050 REMOTE MKJ36998126 (LG) LF 365502420393 172310042030 TAP. SCREW-TP #4.0*20.0L,BLK-ZN 365502420393 172500041250 MAC SCREW-MB M4.0*12.0L,BLK-Ni,NYLOK 365502420393 192511000260 PE BAG 50*80*0.06T...
Page 96
MT5379 (PBGA) FOR FHDTV-120Hz BACK LIGHT CONTROL OPWRSB OPCTRL2 SCHEMATIC- 4 LAYERS OPWRSB OPCTRL2 +3V3SB DV33 OPWM2 HIGH = > OPEN POWER +12V ON (3,4) OPWM2 High = > BL POWER ON OPCTRL1 LOW = > POWER +12V OFF OPCTRL1 Low = >...
Page 109
0.1uF/16V 0.1uF/16V 0.1uF/16V [DISM] : LVDS Data mapping selection Pin L : LG format, H : DISM format (Default value [open] :" L") [BIT_SEL] 10bit or 8bit selection Pin L : 8bit, H :10bit (Default value [open] :"L") APPROVED BY:...
Page 111
DATE 55LV4400_LGE History 2011/05/26 1.Delete unnecessaty prats.(TR107,TR108,TR109,TR110) 2.Modify R361(100)-->2K21, R366(100) --> 1k21, for LED indicator beightness on Page 10. 3.Modify R27(10K) -->0R for PWM voltage on Page 1. 4.Add R122, R128, R255, R251, Q24, Q34 for line out mute on Page 6. 5.Add U2~U23,U25,U27,U29 for ESD test on Page 8.
Need help?
Do you have a question about the 55LV4400 LC550EUH-RDA2-8R1 and is the answer not in the manual?
Questions and answers