Subscribe to Our Youtube Channel
Related Manuals for Zenner EDC
Summary of Contents for Zenner EDC
-
Page 1: Table Of Contents
Configuration EDC Module Configuration manual EDC via ZENNER Device Manager Basic App Table of Contents 1. General information 1.2. Safety instructions 2. Materials required 3 Configuration possibilities EDC 3.1 Set device time 3.2 Set serial number meter 3.3 Set Medium 3.4 Set key date... -
Page 2: General Information
1. General information Be sure to read the operating instructions for the EDC module and for the ZENNER Device Manager Basic app before starting the configuration. This will protect you and prevent damage. Check the contents of the packaging for completeness before installation. Installation and commissioning may only be carried out by qualified personnel. -
Page 3: Materials Required
BTLE RADIO OPTO ZR 3 Configuration possibilities EDC You can view the device information under the Configuration menu item (see ZENNER Device Manager Basic instructions). Select your receiver device. Select "Default" as the device and click on "READ OUT". After successful readout, you will receive the device information of the device read out. Positions marked with a pencil symbol on the left-hand side can be configur3.1 Set device time:... - Page 4 Sends a join request to the LoRaWAN® network. This event indicates that the meter has detected a pipe burst. For EDC modules with M-Bus and pulse: "Pipe Burst" is detected when the flow rate exceeds a certain value (> 30% of Q3) for a Burst period of 30 minutes.
-
Page 5: Set Device Time
3.1 Set device time This function allows you to overwrite the device time of the EDC with that of the mobile device. To do this, proceed as follows: To do this, place the opto head in the designated position on ... -
Page 6: Set Medium
a symbol on the screen. 3.4 Set key date This function allows you to adjust the EDC key date. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. -
Page 7: Set Nominal Flow
3.5 Set nominal flow This function allows you to adjust nominal flow in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. Press the "READ OUT" button in the Configuration area of the ... -
Page 8: Set Communication Scenario
3.7 Set communication scenario This function allows you to adjust communication scenario in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. Press the "READ OUT" button in the Configuration area of the ... -
Page 9: Set Adr
3.10 Send Join Request With this function, you have the option to prompt the EDC to send a "Join Request." Proceed as follows: Place the optical head on the designated spot on the EDC. ... -
Page 10: Smart Functions - Configuration Of Burst
3.11 Smart functions - configuration of burst This function allows you to adjust the smart function “Burst” in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. -
Page 11: Smart Functions - Configuration Of Backflow
3.13 Smart functions - configuration of backflow This function allows you to adjust the smart function “Backflow” in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. -
Page 12: Smart Functions - Configuration Of Blockage
3.16 Smart functions - configuration of leakage This function allows you to adjust the smart function “Leakage” in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on ... -
Page 13: Smart Functions - Configuration Of Reset Leakage
3.17 Smart functions - configuration of reset leakage This function allows you to adjust the smart function “Leakage reset” in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on ... -
Page 14: Smart Functions - Configuration Of Smart Functions
3.19 Smart functions - configuration of smart functions This function allows you to adjust the smart functions in the EDC. To do this, proceed as follows: To do this, place the opto head in the designated position on the EDC. -
Page 15: Clear All Warnings
The successful completion of the command will be indicated by a symbol on the screen. Seite 15 ZENNER International GmbH & Co. KG Heinrich-Barth-Str. 29 | 66115 Saarbrücken Amtsgericht Saarbrücken Geschäftsführer: Telefon +49 681 9 96 76-30 HRA 9741 | HRB 15326... -
Page 16: Example
4. Example with EDC-C wMB 321 V2 WP/WS DN150-300 100L and WPD DN 150 water meter. Set the following parameters to combine the EDC module with the meter: Serial number of the meter You will find the serial number on the meter. Enter the last 8 digits of the serial number.
Need help?
Do you have a question about the EDC and is the answer not in the manual?
Questions and answers