Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Novus TXMINI-M12-MP
Summary of Contents for Novus TXMINI-M12-MP
- Page 1 TXMINI-M12-MP TRANSMITTER USER GUIDE V1.0x A...
-
Page 2: Table Of Contents
SIGNOW SOFTWARE ..................................8 6.3.1 CONNECTING THE DEVICE TO YOUR COMPUTER ....................9 6.3.2 CONFIGURATION SECTION ............................10 6.3.3 DIAGNOSTIC SECTION ...............................10 SIGNOW APP ....................................11 6.4.1 CONNECTING THE DEVICE TO YOUR SMARTPHONE ....................11 6.4.2 RUNNING THE APP ..............................11 OPERATION .........................................13 WARRANTY ........................................14 NOVUS AUTOMATION 2/14... -
Page 3: Safety Alerts
Safety recommendations must be followed to ensure personal safety and prevent damage to the device or system. If the device is used in a manner other than that specified in this manual, the device’s safety protections may not be effective. NOVUS AUTOMATION 3/14... -
Page 4: Introduction
INTRODUCTION TxMini-M12-MP Transmitter is a two-wire 4-20 mA type temperature transmitter powered by the current loop. You can use the SigNow software or app to configure it. To do this, simply connect the TxConfig-M12 Configuration Interface to the computer or smartphone being used. To configure it, the transmitter does not need to be powered. -
Page 5: Specifications
SPECIFICATIONS FEATURES TXMINI-M12-MP Sensor input Pt100: 3-wire type, 0.8 mA excitation, α = 0.00384, according to NBR 13773. IEC 60751 (ITS-90). < 2.5 s. Time between energizing and stabilizing the measurement Accuracy is only guaranteed after 15 minutes. Environment: 25 °C (77 °F) •... -
Page 6: Mechanical Installation
MECHANICAL INSTALLATION TxMini-M12-MP Transmitter is suitable for installation in pipes and in places with limited space. Vibrations, excessive humidity and temperature, electromagnetic interference, high voltage, and other interference can permanently damage the transmitter and cause errors in the measured value. -
Page 7: Electrical Installation
For correct compensation of the RTD cable resistances, they must be equal at all terminals and must not exceed 25 Ω per cable. To guarantee these conditions, it is recommended to use 3 or 4-wire cable of the same length and gauge (the cable is not supplied). NOVUS AUTOMATION 7/14... -
Page 8: Configuration
The transmitter has no electrical insulation between input and output. SIGNOW SOFTWARE SigNow software is the main tool for configuring and analyzing data from TxMini-M12-MP. To install it, simply run the SigNowSetup.exe file and proceed with the configuration. The software and its respective manual can be downloaded for free in the Download Area of our website www.novusautomation.com. -
Page 9: Connecting The Device To Your Computer
6.3.1 CONNECTING THE DEVICE TO YOUR COMPUTER Once the TxConfig-M12 has been connected to the TxMini-M12-MP, connect the transmitter to the computer's USB port and run SigNow, which will display the following screen: Figure 4 To establish a communication, click on Configuration USB:... -
Page 10: Configuration Section
6.3.3 DIAGNOSTIC SECTION By clicking on the Diagnostics tab, you can view the diagnostic data: Figure 7 You can also access the Diagnostics section by clicking on the Diagnostics tab, located on the left of the configuration screen. NOVUS AUTOMATION 10/14... -
Page 11: Signow App
SIGNOW APP The SigNow app is the ideal tool for using the TxMini-M12-MP on a daily basis. Available for Android smartphones, it is always easily accessible for monitoring or configuring the device. SigNow can be downloaded for free from Google Play Store. - Page 12 Apart from the particularities of the connection mode, the parameters and division of information are the same as in the SigNow software. More specific information about the application's buttons can be found in the SigNow manual, available on NOVUS website.
-
Page 13: Operation
The USB connection can be made even when the transmitter is connected to the process and operating, without causing errors in the measurement. Note: When checking or calibrating the transmitter, check that the Pt100 excitation current required by the calibrator is compatible with the Pt100 excitation current used in this instrument: 0.170 mA. NOVUS AUTOMATION 13/14... -
Page 14: Warranty
WARRANTY Warranty conditions are available on our website www.novusautomation.com/warranty. NOVUS AUTOMATION 14/14...
Need help?
Do you have a question about the TXMINI-M12-MP and is the answer not in the manual?
Questions and answers