Advertisement
Quick Links
Advertisement
Related Manuals for XAG ACS2
Summary of Contents for XAG ACS2
- Page 1 ACS2 Control Stick Quick Start Guide Version 1.0...
- Page 3 Dear user, thank you for choosing XAG products. For safety reasons and to ensure the best experience possible, XAG recommends that you read through the Quick Start Guide and Disclaimer in this document before attempting to use the ACS2 ControlStick.
-
Page 4: List Of Items
List of Items Please carefully check if the product contains all the items listed below and your dealer if there are any missing items. USB To Type-C Micro USB To Type-C Type-C To Type-C Cable Cable Cable × 1 × 1 ×... - Page 5 Getting to Know ControlStick The main structural components of the ACS2 ControlStick are as follows: Flight Control Cable Port SIM Card Slot Panel (Type-C) Speed Control Power Button Status Indicator * Differential Positioning Cooling Smart Mode Module Port Component Spray/Spread...
- Page 6 ControlStick Overview • Inserting SIM card 1. Remove the rubber plug ① on the left side of the ControlStick. Cut corner ① 2. I n s e r t t h e S I M c a r d i n t h e of SIM card direction shown on the right.
- Page 7 • Connecting to mobile phone 1. Open your mobile phone, find the hotspot of the remote control in the Wi-Fi list and enter the corresponding password to connect. (The default hotspot name is “ACS2_XXX”, in which XXX is the serial number marked on the top of the remote control, and the default password is 20070401.) 2.
- Page 8 1. Open the Xplanet App and click 2. To view more parameters, you the icon (01) may slide down (see Figure 3) Please select ControlStick an operation Basic Information Device Type ACS2 ControlStick Power Level Volume High Communication Configuration Operating Mode Hotspot Name Password Channel...
- Page 9 Hands-on Instruction • Take-off Press and hold both Altitude Control buttons for 3 seconds, and the UAS will automatically take off and hover at 2.5 meters. Release the buttons within 3 seconds to cancel the take-off order • Land/Return 1. Land: Press and hold both Altitude Control buttons to land the UAS (see the figure above) 2.
- Page 10 • Altitude control 1. Go up: Press and hold the Up button above 2. Go down: Press and hold the Down button below • Pitch/Roll/Hover control 1. Press the Up/Down buttons to tilt the UAS up and down 2. Press the Left/Right button to tilt the UAS left and right 3.
- Page 11 • Speed control 1. Speed up: Press the + button above the V button 2. Speed down: Press the – button below the V button Notes: Press the V button to activate the highest voice broadcast speed in the current setting •...
- Page 12 A-B Point Mode 1. Defining points ① . Fly the UAS to the designated location, press the A button twice to define the location as Point A ② . Fly the UAS to the designated location, press the B button twice to define the location as Point B 2.
-
Page 13: Other Operations
3 . Changing route ① . Switch to manual mode: Press the Smart Mode button twice until a voice prompt "Manual Mode" is heard from the Con- trolStick ② . Press the A/B button to select another route 4 . Exit Press any action button or Smart Mode button to exit the A-B Point Mode Rover mode... - Page 14 1. Upgrade the ControlStick via the Xplanet App: Open the XPlanet App, click the profile photo on the upper left corner to open the menu, select "Device"-"ACS2"-"Check Updates", tick the box on the right to choose the firmware to be updated, and finally click “Upgrade Now".
- Page 15 Type-C end into the port at the upper part of the ControlStick. Upon connection, the PC will show a flash drive is inserted, and please copy the ACS2.fw file to the flash drive. ③ Unplug the cable, and then press and hold the Down button...
- Page 16 Status Description (from left to right) Power light Status Green light on Power level 60%~100% Yellow light on Power level 30%~59% Red light on Power level 5%~29% Power level lower than 5%, voice Quick flash (red) alert on, about to power off Device Connection light Status Rover mode...
-
Page 17: Technical Specifications
Technical Specifications Model: ACS2 Dimensions: 76mm×60mm×177mm Operating frequency: 2.4Ghz/5.8GHz Transmitting power: 23dbm Mobile phone operating system supported: Android Built-in battery capacity: 4500 mAh /32 Wh Ambient temperature for charging: 5 ℃ - 45 ℃ Max. signal range (no interference/obstruction): 800 m Charging voltage/current: 5V/2A, 9V/1.5A, 12V/1.5A... - Page 18 XAG may not be held liable. 4. To the maximum extent permitted by law, XAG shall not be liable for all losses caused by users' failure to use the product in accordance with this document and the “Product Manual/Operation Manual”.
- Page 19 Strong safety awareness is required to operate this product. Do not use the parts that are not provided or suggested by XAG. Please strictly follow the instructions of XAG to install and use the product.
- Page 20 Visit our website for more information @XAGofficial www.xa.com/en @XAG_official This Guide is subject to upgrade @XAG Official without prior notice.
Need help?
Do you have a question about the ACS2 and is the answer not in the manual?
Questions and answers