Related Manuals for Baldwin Boxall BVRD2M4
Summary of Contents for Baldwin Boxall BVRD2M4
- Page 1 BVRD2M4 Installation Instructions Manual name: BVRD2M4 Mini Router Issue: 6 ECR: 3149 Date of issue: November 2016 www.acornfiresecurity.com...
- Page 2 BVRD2M4 Installation Instructions © November 2016 Baldwin Boxall Communications Limited This equipment has been designed and manufactured to conform to the following EC Standards: EMC: EN55103-1 Environment Classification: E1, EMC: EN55103-2 Environment Classification: E5, Safety: EN60065 Failure to use the equipment in the manner described in the product literature will invalidate the conformity.
-
Page 3: Table Of Contents
Four Single Monitored Zones ____________________________9 Four Dual Circuit Zones_______________________________ 10 Three Zones with Reserve Amp _________________________ 11 BVRDNET Network__________________________________ 12 Firmware Configuration Introduction________________________________________ 13 BVRD USB Config Software ____________________________ 13 Mute Fault Sounder Option_____________________________ 14 BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... - Page 4 BVRD2M4 Installation Instructions BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com...
-
Page 5: Amendment Record
Baldwin Boxall Communications Limited. The possession of this manual and the use of the information is, therefore, restricted only to those persons duly authorised by Baldwin Boxall Communications Limited. Do not reproduce, transcribe, store in a retrieval system or translate into any language, any part of this manual without the prior permission of Baldwin Boxall Communications Limited. -
Page 6: Safety Information
Notes are statements that are useful to the user in the context of a particular section of the manual, e.g. : Do not speak into the microphone until the "Speak Now" LED is illuminated. OMMENTS BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... - Page 7 There is also an “All Call” fail safe embedded Evacuate message that can be broadcast in the unlikely event of DSP failure. The BVRD2M4 is fully monitored and includes a real time clock that is used for date stamping the stored fault / event log.
-
Page 8: Front Panel Indicators & Controls
1.1 F & RONT ANEL NDICATORS ONTROLS Figure 1.1 — BVRD2M4 Front Panel Ident Description LINE / AMP 1 - 4 :will illuminate if a Line or Amp fault is detected PSU 1&2: will illuminate if either PSU is disconnected ... -
Page 9: Rear Panel Connections
Common Fault Output (1 x volt free relay changeover contact for Common Fault) e) Input 1 Hardwire Access The BVRD2M4 requires two seperate 24V DC supplies. 24V DC Supply A fault will be announced if either of the supplies is not connected. -
Page 10: Side Panel Controls
BVRD2M4 Installation Instructions 1.3 S ANEL ONTROLS Figure 1.3 — BVRD2M4 Side Panel Controls BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 11: Bvrd2M4 Specifications
Messages Flash PROM Storage Medium Flash PROM (non volatile) Maximum Message Length 57 Seconds Frequency Response -3dB @ 50Hz and 18KHz Signal to Noise Ratio Better than 65dB Power Requirement 22V to 35V @ 500mA max BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 12: Audio Output Specifications
2 x RS485 half duplex ports for communicating to control microphones, fire detection systems, network control, fault reporting etc. 1 x front panel mounted USB port to configure the system, obtain fault and activity logs, upload messages etc. BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 13: Installation Examples
2 Installation Examples 2.1 O VERVIEW The BVRD2M4 has been designed to enable simple and easy configuration for small systems of 4 zones or less. The outputs can be configured as follows: a. Up to 4 single zone monitored outputs, b. -
Page 14: Termination Pcb Options
: Control Output 1 is reserved for the "VA Active" Indicator. Control Outputs 6, 7, and 8 are automatically reserved for Changeover control if an Output is configured to have a "Reserve" amplifier in configuration. BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 15: Four Single Monitored Zones
BVRD2M4 Installation Instructions 2.3 F INGLE ONITORED ONES Figure 2.2 — Connection Details for Four Single Zones BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 16: Four Dual Circuit Zones
BVRD2M4 Installation Instructions 2.4 F IRCUIT ONES Figure 2.3 — Connection Details for Four Dual Zones BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 17: Three Zones With Reserve Amp
BVRD2M4 Installation Instructions 2.5 T HREE ONES WITH ESERVE Figure 2.4 — Connection Details for Three Zones with Reserve Amp BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 18: Bvrdnet Network
BVRD2M4 Installation Instructions 2.6 BVRDNET N ETWORK If a BVRDNET Network card is installed in the BVRD2M4 please refer to the BVRDNET Installation Manual for relevant information. BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com... -
Page 19: Firmware Configuration
PC / Laptop running “Vigil EVAS BVRD2M Configuration Software”. : It is possible to make configuration changes to any BVRD2M4 units on a network via the front panel of any unit on the network. 3.2 BVRD USB C... -
Page 20: Mute Fault Sounder Option
Press and hold the “Lamp Test” and “Fault Reset” buttons, c. Reconnect power and hold the buttons for 3 seconds. To enable the Sounder remove power, hold the Reset button and reconnect power. BVRD2M4 Mini Router issue 6 www.acornfiresecurity.com...
Need help?
Do you have a question about the BVRD2M4 and is the answer not in the manual?
Questions and answers