Related Manuals for PV-ezRack SolarRoof Pro U Support and Mycro Rail
Summary of Contents for PV-ezRack SolarRoof Pro U Support and Mycro Rail
- Page 1 U Support and Mycro Rail Code-Compliant Planning and Installation Guide V 6.0 Complying with AS/NZS 1170.2:2021 Last Updated - Nov. 2023...
-
Page 2: Table Of Contents
Installation Guide / SolarRoof Tilt Legs Introduction The installer is solely responsible for: Clenergy PV-ezRack SolarRoof Pro, U Support and Mycro Rail are widely used for PV Module mounting on tin roofs. With rail and rail-less solution, it can easily •... -
Page 3: Planning
Installation Guide / SolarRoof Tilt Legs Planning Determine the wind region of your installation site Wind Regions – Australia Wind regions are pre-defined for the whole of Australia by the Australian Standard 1170.2:2021. Comparing to 1170.2:2011, 2021 version has a lot of changes in wind regions. •... -
Page 4: Tools & Components
Installation Guide / SolarRoof Tilt Legs Tools and Components Tools Screw Driver Torque Spanner Spanner 5m Tape String & Marker Pen (for M8 Hexagon Socket Screw) Components ER-EC-ST ER-R-ECO ER-IC-ST C-U/30/46 ER-SP-ECO End Clamp ECO-Rail Splice for ECO-Rail Inter Clamp Universal Clamp CRC-R/ECO-ZBW ER-R-MC/380... -
Page 5: System Overview
Installation Guide / SolarRoof Tilt Legs System Overview With rail ② ⑤ ① ③ ④ 1. End Clamp 2. Inter Clamp 3. ECO Rail 4. U Support, 120mm 5. Mycro rail, 380mm Without rail ④ ② ③ ① 1. End Clamp 2. - Page 6 Installation Guide / SolarRoof Tilt Legs Precautions during Stainless Steel Fastener Installation Improper operation may lead to deadlock of Nuts and Bolts. The steps below should be applied to stainless steel nut and bolt assembly to reduce this risk. General installation instructions: (1) Apply force to fasteners in the direction of thread (2) Apply force uniformly, to maintain the required torque (3) Professional tools and tool belts are recommended...
-
Page 7: Installation Instruction
Installation Guide / SolarRoof Tilt Legs Installation Instructions U Support Installation According to your plan, mark the position of the U Support on the tin roof with a Marker Pen and String. Place the U Support on the marked position, as shown in the figures on the right. -
Page 8: Rail Installation
Installation Guide / SolarRoof Tilt Legs Cross Connector Clamp of ECO-Rail Installation When using Cross Connector Clamp of ECO-Rail, fix the Cross Connector Clamp of ECO-Rail on the Z module channel of U support or Mycro Rail. Fasten the bolt of the Cross Connector Clamp slightly before installing the ECO - Rail. - Page 9 Installation Guide / SolarRoof Tilt Legs Place the ECO-Rail on the U support or Mycro Rail, uplift the Rail Clamp and click it into the side channels of the ECO-Rail as shown in the right figures. Fasten the Rail Clamp within 16-20 N.m torque after the Rail is positioned properly.
- Page 10 Installation Guide / SolarRoof Tilt Legs Loosely place the next framed PV Module into the other side of the Inter Clamp and as shown in Figures on the right. Recommend torque of M8 bolt is 16~20N.m Without Rail Place the first PV Module on the U support or Mycro Rail according to your plan, and fix it in place using the End Clamps.
- Page 11 Installation Guide / SolarRoof Tilt Legs Repeat above steps to install the rest PV-Modules. U Support Mycro Rail Code-Compliant Planning and Installation Guide V 6.0 - Complying with AS/NZS 1170.2:2021...
- Page 12 Clenergy 1/10 Duerdin St Phone: +61 3 9239 8088 Clayton VIC 3168 Email: sales@clenergy.com.au Australia Web: www.clenergy.com.au @ClenergyGlobal / @ClenergyClub / ClenergyAUS @Clenergy @ClenergyClub @Clenergy_global @Clenergy A Clenergy Technologies Company...
Need help?
Do you have a question about the SolarRoof Pro U Support and Mycro Rail and is the answer not in the manual?
Questions and answers