Related Manuals for Caple VAP3IN1/SS
Summary of Contents for Caple VAP3IN1/SS
- Page 1 Instruction manual for 3IN1 steaming water tap Model code: VAP3IN1/SS, VAPQ3IN1/SS Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk...
-
Page 2: Safety Instructions
- By clients in hotels, motels and other residential type environments. To avoid all risk, if the plug or power cable is damaged, it must only be replaced by a Caple appointed engineer. Do not wash children, hair or any pets in a sink within reach of this 3IN1 steaming water tap. - Page 3 This appliance is designed solely to dispense hot and cold water, also to dispense near boiling water. Other types of use are not permitted and may prove dangerous. Caple will not be held liable for any damage caused by the incorrect use of the appliance.
-
Page 4: Ce Declarations Of Conformity
Important Caple cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that Caple reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. The guarantee may become void in... -
Page 5: Accessories Supplied
household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local council, your household waste disposal service or the retailer where you purchased the product. - Page 6 When installing the dispenser, you should allow 10 to 15 cm of space around it for ventilation. You must never use a spare part which is not recommended by Caple. The temperature adjustment knob/switch controls the water temperature, not the water flow, please take care when turning not to force the knob.
-
Page 7: Installation Steps
Installation The power outlet must be correctly earthed and also be able to be isolated by a switch. Use a separate circuit for the boiler, which is also correctly earthed. The tap can be installed into the sink or the worktop using a 35mm hole. Install the water boiler vertically, it must not be placed on its side. - Page 8 Screw the two flexible hoses into the base of the tap, the red hose connects the hot water and the blue hose connects the cold water. Screw in the push fit ‘quick connector’ with the supplied o’ring into the metal tube at the base of the tap.
- Page 9 Connect the transparent silicone tube to the tap using the hose clamp to secure it in place. Connect the other side of this silicone tube to the hot water outlet in the middle of the water tank and again use the hose clamp to secure it in place. Turn on the standard cold/hot water supply by using the right hand handle on the tap to test the cold water (blue colour indicator) and hot water (red colour indicator).
-
Page 10: Operation
light behind the temperature control knob will illuminate blue once it has reached 98°C. Use the left hand safety lever to start the flow of steaming water. NOTE it may take a few seconds for the water to begin to flow as it makes the way up the tube (the time will vary depending on the length of the tube). - Page 11 NOTE hot water and steam can periodically be released from the tap when it is not in use. This is normal and is due to the high operational temperature and the boiling water in the tank. Steam is given off which rises up through the tubes and spout. Lowering the temperature of the boiler slightly can reduce this effect.
-
Page 12: Care And Maintenance
Care and maintenance IMPORTANT you must not perform any care or maintenance on this product without first switching off the power supply and disconnecting the boiler from the mains. Cleaning This product can be cleaned by simply using warm water with a small amount of mild detergent added. -
Page 13: Troubleshooting
If you have a problem which cannot be resolved by using the troubleshooting table please contact Caple Service, either by telephone on 0117 938 7420 or by email service@caple.co.uk. - Page 14 Please quote the model and serial number when contacting Caple service. The serial number can be found on the rating plate positioned on the back of the boiler. Serial number_____________________________ Purchase date_____________________________ Boiler technical specification Rated Voltage: 220V Rated Frequency:...
- Page 16 Caple Fourth Way Avonmouth Bristol BS11 8DW t: 0117 938 1900 e: service@caple.co.uk www.caple.co.uk V2 - 01/2017...
Need help?
Do you have a question about the VAP3IN1/SS and is the answer not in the manual?
Questions and answers